LAISHA
Open Laisha

ASRB NET Farm Machinery Testing, Evaluation & Standards: practice questions

ASRB NET — Farm Machinery & Power / Land & Water Management Engineering / Agricultural Structures & Process Engineering · India · Agricultural Scientists Recruitment Board (ICAR)

Original practice questions written to the published syllabus · not past papers
10worked here, free
33written to this exam in this subject
12syllabus units

About ASRB NET

ASRB NET — Farm Machinery & Power / Land & Water Management Engineering / Agricultural Structures & Process Engineering is a specialist certification exam run by Agricultural Scientists Recruitment Board (ICAR), for candidates in India. NET: 150 MCQs, 150 marks, 2 hours, −1/3 per wrong answer, English/Hindi, PG level. Combined NET/ARS/SMS/STO recruitment runs prelims, mains and interview.

Official site: pw.live.

We have not been able to confirm these details against the exam body's own specification, so fees, dates and pass marks are left out on purpose. Check the current format, eligibility, fees and dates on the official site.

Farm Machinery Testing, Evaluation & Standards in ASRB NET

Lecturer-level understanding of testing standards (OECD, ISO, BIS), instrumentation and calibration, laboratory accreditation, and reasoning about why a test is done a certain way.

How tractors and implements are tested against codes, and how to read a test report.

Our 33 ASRB NET questions in this subject: 3 easy, 16 medium, 14 hard, across 12 units.

10 practice questions, worked

Choose an answer, then open the working. Each explanation says why the right answer is right and why the others are not.

These 10 were written to ASRB NET and are not shown on any other exam's page.

Question 1 · medium

Which statement correctly contrasts the OECD tractor performance code (Code 2) with the OECD rollover protective structure codes?

  1. Code 2 reports measured values without a pass mark; the ROPS codes apply acceptance criteria
  2. Code 2 sets a minimum PTO power for each class, while the ROPS codes only report deflections
  3. Both apply pass marks, and Code 2 requires SFC below one fixed limit for every tractor size
  4. Neither applies criteria; ROPS deflections are just reported for the buyer to judge as wished
Answer and working

A. Code 2 reports measured values without a pass mark; the ROPS codes apply acceptance criteria

The performance code measures and reports; it does not fail a tractor for low power or high fuel use. The protective-structure codes are acceptance codes: the structure must keep the clearance zone intact and must not break, so a structure can fail.

Question 2 · easy

OECD Code 5 for agricultural and forestry tractors deals with

  1. static strength testing of rollover structures
  2. measurement of A-weighted noise at the driver's seated position
  3. performance at the PTO, drawbar and hydraulics
  4. falling object protective structures on the cab
Answer and working

B. measurement of A-weighted noise at the driver's seated position

Code 5 is the noise code. Static ROPS testing is Code 4, performance is Code 2, and falling object protection is Code 10.

Question 3 · medium

A forestry tractor fitted with a front loader will work under trees and stacks of logs. The OECD code under which its cab roof protection against falling objects is tested is

  1. Code 8, protective structures on track-laying tractors
  2. Code 3, dynamic testing of rollover structures
  3. Code 2, performance at PTO, drawbar and hydraulics
  4. Code 10, falling object protective structures on the cab
Answer and working

D. Code 10, falling object protective structures on the cab

Protection against falling objects is the FOPS code, Code 10. Code 8 is for track-layers' rollover protection, Code 3 is the dynamic ROPS test, and Code 2 is the performance code; none of these tests a roof against falling objects.

Question 4 · medium

A falling object protective structure (FOPS) is tested by

  1. pushing the structure sideways with a ram until it reaches a set energy
  2. swinging a pendulum block into the rear of the structure from a set height
  3. dropping a standard object onto the roof from a height giving set energy
  4. overturning the tractor on a test slope with a dummy belted in the seat
Answer and working

C. dropping a standard object onto the roof from a height giving set energy

A FOPS protects against objects falling from above, so the test drops an object onto the roof and checks it does not enter the protected zone. Sideways ram loading and pendulum impacts are ROPS tests; full overturns are not the test method.

Question 5 · hard

An eddy-current dynamometer produces its braking torque by

  1. water churned between rotor vanes and stator pockets inside a sealed casing
  2. dry friction between a band and a drum that is cooled by a water spray
  3. eddy currents induced by a coil's magnetic field as the toothed rotor turns
  4. an electric generator feeding power back into the mains through an inverter
Answer and working

C. eddy currents induced by a coil's magnetic field as the toothed rotor turns

A coil sets a magnetic field; as the rotor turns the flux changes, and the induced eddy currents (in the rotor or, in common water-cooled designs, in the stator loss plates) oppose the motion, producing torque and heat that is carried away by cooling water. Water churning is the hydraulic dynamometer, a band on a drum is a friction brake, and regenerating to the mains is an electric (AC) dynamometer.

Question 6 · medium

The volume median diameter (VMD, Dv0.5) of a spray is the droplet diameter

  1. below which half of all the droplets fall by number
  2. of the single largest droplet measured in the spray
  3. below which droplets make up half the total spray volume
  4. that occurs most often in the measured size spectrum
Answer and working

C. below which droplets make up half the total spray volume

VMD splits the spray volume into two equal halves. The diameter splitting the droplet count is the number median diameter; the largest droplet and the most frequent size (mode) are different statistics. The VMD/NMD ratio indicates the spread of sizes.

Question 7 · easy

The ISO standard that sets out inspection of agricultural sprayers already in use (leaks, gauges, nozzle output, boom stability) is

  1. ISO 5682
  2. ISO 5008
  3. ISO 5700
  4. ISO 16122
Answer and working

D. ISO 16122

ISO 16122 covers inspection of sprayers in use. ISO 5682 gives laboratory test methods for spray equipment, ISO 5008 measures whole-body vibration, and ISO 5700 is the static ROPS test.

Question 8 · hard

Tractor A was tested ballasted on a concrete track under the OECD code. Tractor B, of similar PTO power, was tested unballasted on a soil track under a national code. A's maximum drawbar pull is much higher. The correct conclusion is that

  1. the pulls cannot be compared, since surface, ballast and code all differ between them
  2. A has the better transmission, because drawbar pull measures gearbox quality
  3. B has the more efficient engine, because a soil track needs less fuel per kWh
  4. A will pull more in any field, because concrete results always rank correctly
Answer and working

A. the pulls cannot be compared, since surface, ballast and code all differ between them

Maximum pull is limited by traction, which depends on the surface and the load on the driving wheels; A's ballast and concrete track both raise it. With code, surface and ballast all different, the difference tells nothing about the tractors themselves. Drawbar pull is not a measure of gearbox quality or engine efficiency.

Question 9 · medium

In a tractor test report, a high torque backup at the PTO indicates that the tractor

  1. will use less fuel per kWh at every load than one with a low backup
  2. has a higher maximum engine speed and so a faster top road speed
  3. lugs through a brief overload with no gear change
  4. has a larger hydraulic lift force through the full range of the hitch
Answer and working

C. lugs through a brief overload with no gear change

Torque backup is the rise in torque as the engine slows below rated speed under load; a high value lets the engine lug through a hard patch rather than stall. It does not determine SFC at every load, top speed or lift force.

Question 10 · hard

A test report gives the maximum drawbar power of a tractor on a concrete track as 80 per cent of its maximum PTO power. A researcher wants to estimate drawbar power in tilled soil. The most defensible approach is to

  1. use the 80 per cent track ratio unchanged, since it is set by the transmission alone
  2. raise the ratio above 80 per cent, since soft soil lets the tyres grip with less slip
  3. use the ratio of engine to PTO power, since drawbar losses match transmission losses
  4. apply a lower, soil-specific ratio from traction theory or field data
Answer and working

D. apply a lower, soil-specific ratio from traction theory or field data

On a hard track rolling resistance and slip are small; in tilled soil both rise, so the drawbar-to-PTO ratio falls. Estimating field drawbar power needs a soil-specific ratio from traction prediction or measured field data. The track ratio is not set by the transmission alone, soft soil increases slip, and drawbar losses include tyre and soil losses, not only gear losses.

A study plan for Farm Machinery Testing, Evaluation & Standards in ASRB NET

This plan follows where our questions actually fall, so the time goes where the marks are likely to be. It is our reading of the syllabus, not the exam body's weighting.

  1. First, the heavy units (48% of the 33 questions): Test codes: OECD, BIS, PAES/PNS, ASABE and ISO (6, 18%); Interpreting test reports (4, 12%); Drawbar performance test (3, 9%); Hydraulic lift test (3, 9%).

    Read the manual chapters for these first and do every worked question you can find on them.

  2. Then the middle band: Noise at the operator's ear (3, 9%); ROPS and FOPS tests (3, 9%); Types of tests: commercial, batch, confidential and prototype (3, 9%); Laboratory and field tests of tillage and sowing equipment (2, 6%).

    Aim for one sitting per unit, then mixed questions across them.

  3. Then the lighter units: Test instrumentation: dynamometers and fuel meters (2, 6%); Tests of sprayers and harvesting equipment (2, 6%); Brake and turning tests (1, 3%); PTO performance test (1, 3%).

    Learn the definitions, classifications and standard numbers; these units are more often recalled than worked.

  4. Leave time for the hard ones: Brake and turning tests (1 hard of 1), PTO performance test (1 hard of 1), Interpreting test reports (3 hard of 4).

    Come back to these after a first pass, untimed, and read every explanation, including for the options you rejected.

  5. Bank the easy marks: Tests of sprayers and harvesting equipment (1 easy of 2); Drawbar performance test (1 easy of 3).

    Do these early in revision so they are fast on the day.

  6. Finish timed. Sit the subject as a timed set without notes, mark it, and send each wrong answer back to its unit above.

Last updated · How Laisha writes and checks its pages · Report a mistake

Ask Laisha about this

Opens Laisha's chat with your question ready to send. Sign in or start free.

Unlock every question — ASRB NET Farm Machinery Testing, Evaluation & Standards

US$10 a month · one price worldwide · cancel any time

  • Every practice question in this subject, with full working
  • Timed exam papers and progress by unit
  • Ask Laisha to explain any answer — up to 1,000 questions a month
Free or Smarter
FreeSmarter
Grow guides, pest pages, articlesRead allRead all
Ask Laisha5 a dayUp to 1,000 a month
Exam practiceThe sample on each pageEvery question, timed papers
Crop calendar and pest alerts—For your own fields
Calculators and tools—All
Uploads and reports—100 a month, real files
10 days free for every new account, no card.