LAISHA
Open Laisha

ICAR AIEEA-PG Farm Machinery Testing, Evaluation & Standards: practice questions

ICAR AIEEA-PG — Agricultural Engineering & Technology (Major Subject Group 10) · India · National Testing Agency for ICAR

Original practice questions written to the published syllabus · not past papers
10worked here, free
38written to this exam in this subject
12syllabus units

About ICAR AIEEA-PG

ICAR AIEEA-PG — Agricultural Engineering & Technology (Major Subject Group 10) is a postgraduate admission exam run by National Testing Agency for ICAR, for candidates in India. Computer-based, 120 minutes, 120 MCQs, +4 / −1, English only (2026 bulletin). One paper for the whole subject group.

Source: icar.org.in.

Checked against the exam body's published information. Formats and fees change; confirm the current edition there before you book.

Farm Machinery Testing, Evaluation & Standards in ICAR AIEEA-PG

Unit V test codes and procedure: types of test (commercial, batch, confidential), names of OECD codes and what each covers, which test measures what, dynamometer types, ROPS purpose; mostly recall with short calculations.

How tractors and implements are tested against codes, and how to read a test report.

Our 38 ICAR AIEEA-PG questions in this subject: 15 easy, 23 medium, 0 hard, across 12 units.

10 practice questions, worked

Choose an answer, then open the working. Each explanation says why the right answer is right and why the others are not.

These 10 were written to ICAR AIEEA-PG and are not shown on any other exam's page.

Question 1 · easy

The OECD Standard Code that covers the performance testing of agricultural tractors — PTO, hydraulic and drawbar power and fuel consumption — is

  1. Code 2
  2. Code 4
  3. Code 5
  4. Code 10
Answer and working

A. Code 2

Code 2 is the performance code. Code 4 is the static ROPS test for standard tractors, Code 5 is noise at the driver's position, and Code 10 covers falling object protective structures.

Question 2 · medium

The main reason the OECD tractor codes were set up was to

  1. fix a world price for tractors so that importers cannot undercut makers
  2. replace all national road-safety rules for tractors with one OECD law
  3. license tractor operators through a single international driving test
  4. make a test report from one member country recognised in the others
Answer and working

D. make a test report from one member country recognised in the others

The codes, begun in 1959, give a common test method so that a report approved under the scheme is accepted by all participating countries, easing trade. They do not set prices, do not replace national road law, and do not license operators.

Question 3 · medium

During a PTO test the dynamometer records a torque of 220 N·m at a PTO speed of 540 rev/min. The PTO power is

  1. 746.4 kW
  2. 12.44 kW
  3. 23.04 kW
  4. 1.98 kW
Answer and working

B. 12.44 kW

P = 2πNT/60 = 2π × 540 × 220 / 60 = 12441 W = 12.44 kW. Leaving out the /60 gives 746.4 kW; using 1000 rev/min gives 23.04 kW; leaving out 2π gives 1.98 kW.

Question 4 · medium

In a tractor PTO performance test, the maximum torque and the speed at which it occurs are found from

  1. part-load runs at a fixed governor setting with load reduced in steps
  2. full-governor runs with load raised beyond rated speed, down the lug curve
  3. a no-load run at high idle, reading the torque as the governor cuts in
  4. a single run at the standard PTO speed, holding that speed for one hour
Answer and working

B. full-governor runs with load raised beyond rated speed, down the lug curve

With the governor control at full, raising the load past the rated point makes the engine slow down and the torque rise to its maximum; those runs trace the lug curve. Part-load runs give fuel use at partial loads, high idle carries almost no torque, and a run at standard PTO speed gives power at that speed only.

Question 5 · medium

During the tractor hydraulic power test, the maximum pressure that can be reached in the external circuit is set by

  1. the volumetric efficiency of the gear pump
  2. the diameter of the external hose couplers
  3. the pressure relief valve setting
  4. the temperature of the oil in the reservoir
Answer and working

C. the pressure relief valve setting

The relief valve opens at its set pressure and limits the circuit pressure; the report states that setting. Pump efficiency affects delivery, coupler size affects pressure drop at high flow, and oil temperature affects viscosity and leakage, but none of these fixes the maximum pressure.

Question 6 · medium

Two independent noise sources each produce 86 dB(A) at the operator's ear. The combined level is

  1. 172 dB(A)
  2. 86 dB(A)
  3. 92 dB(A)
  4. 89 dB(A)
Answer and working

D. 89 dB(A)

L = 10 log₁₀(2 × 10^8.6) = 86 + 10 log₁₀ 2 = 89.0 dB(A). Decibels are not added arithmetically (172); a second equal source does add energy, so 86 is wrong; +6 dB applies to doubling sound pressure from coherent sources, not to two independent sources.

Question 7 · medium

In a hydraulic (water-brake) dynamometer used for PTO testing, the load on the engine is varied by

  1. changing the current in a coil that sets a magnetic field
  2. tightening a rope or band around a rotating brake drum
  3. changing the gear ratio between the PTO and the rotor
  4. changing the water level in the casing around the rotor
Answer and working

D. changing the water level in the casing around the rotor

A water brake absorbs power by churning water; more water means more resistance. Coil current controls an eddy-current dynamometer, a rope or band is a friction brake, and gear ratio changes do not set dynamometer load.

Question 8 · medium

In a combine harvester field test, grain lost over the straw walkers or out of the rotor discharge with the straw is classed as

  1. header loss
  2. separation loss
  3. cleaning (shoe) loss
  4. pre-harvest loss
Answer and working

B. separation loss

Free grain that the separating unit fails to recover and that leaves with the straw is separation loss. Header loss happens at the cutter bar and reel, cleaning loss leaves from the sieves with the chaff, and pre-harvest loss is on the ground before the machine arrives.

Question 9 · medium

A brochure states 50 hp engine power; the official test report for the same model gives 42 hp maximum PTO power. A buyer should conclude that

  1. the test station measured wrongly, since a brochure figure is a legal guarantee
  2. the tractor is defective and is losing 16 per cent of its power through wear
  3. the figures are taken at different points and are not directly comparable
  4. the report is out of date, since PTO power rises as the engine wears in
Answer and working

C. the figures are taken at different points and are not directly comparable

Flywheel (engine) power is measured before the transmission and PTO power after it, so PTO power is lower by the transmission losses. That gap is normal and not evidence of a fault or an error. The tolerance between declared and measured values is set by each code or rule, and should be checked against the like-for-like quantity.

Question 10 · easy

In a dynamometer, the casing is mounted on trunnion bearings and restrained by a torque arm. This arrangement allows

  1. the rotor to spin freely so the engine carries no load
  2. the water flow to be measured as it leaves the casing
  3. the engine speed to be raised above its governed limit
  4. the casing's reaction torque to be measured by a load cell
Answer and working

D. the casing's reaction torque to be measured by a load cell

Whatever torque the rotor applies to the casing (by water, magnetism or friction) tends to rotate the casing; the torque arm and load cell measure that reaction, which equals the shaft torque. The trunnions do not unload the engine, measure water flow, or affect governed speed.

A study plan for Farm Machinery Testing, Evaluation & Standards in ICAR AIEEA-PG

This plan follows where our questions actually fall, so the time goes where the marks are likely to be. It is our reading of the syllabus, not the exam body's weighting.

  1. First, the heavy units (42% of the 38 questions): PTO performance test (5, 13%); Test instrumentation: dynamometers and fuel meters (4, 11%); Tests of sprayers and harvesting equipment (4, 11%); Brake and turning tests (3, 8%).

    Read the manual chapters for these first and do every worked question you can find on them.

  2. Then the middle band: Drawbar performance test (3, 8%); Hydraulic lift test (3, 8%); Laboratory and field tests of tillage and sowing equipment (3, 8%); ROPS and FOPS tests (3, 8%).

    Aim for one sitting per unit, then mixed questions across them.

  3. Then the lighter units: Test codes: OECD, BIS, PAES/PNS, ASABE and ISO (3, 8%); Types of tests: commercial, batch, confidential and prototype (3, 8%); Interpreting test reports (2, 5%); Noise at the operator's ear (2, 5%).

    Learn the definitions, classifications and standard numbers; these units are more often recalled than worked.

  4. Bank the easy marks: Drawbar performance test (2 easy of 3); Test codes: OECD, BIS, PAES/PNS, ASABE and ISO (2 easy of 3).

    Do these early in revision so they are fast on the day.

  5. Finish timed. Sit the subject as a timed set without notes, mark it, and send each wrong answer back to its unit above.

Last updated · How Laisha writes and checks its pages · Report a mistake

Ask Laisha about this

Opens Laisha's chat with your question ready to send. Sign in or start free.

Unlock every question — ICAR AIEEA-PG Farm Machinery Testing, Evaluation & Standards

US$10 a month · one price worldwide · cancel any time

  • Every practice question in this subject, with full working
  • Timed exam papers and progress by unit
  • Ask Laisha to explain any answer — up to 1,000 questions a month
Free or Smarter
FreeSmarter
Grow guides, pest pages, articlesRead allRead all
Ask Laisha5 a dayUp to 1,000 a month
Exam practiceThe sample on each pageEvery question, timed papers
Crop calendar and pest alerts—For your own fields
Calculators and tools—All
Uploads and reports—100 a month, real files
10 days free for every new account, no card.