LAISHA
Open Laisha

ICAR AIEEA-PG Engineering Thermodynamics: practice questions

ICAR AIEEA-PG — Agricultural Engineering & Technology (Major Subject Group 10) · India · National Testing Agency for ICAR

Original practice questions written to the published syllabus · not past papers
10worked here, free
96written to this exam in this subject
9syllabus units

About ICAR AIEEA-PG

ICAR AIEEA-PG — Agricultural Engineering & Technology (Major Subject Group 10) is a postgraduate admission exam run by National Testing Agency for ICAR, for candidates in India. Computer-based, 120 minutes, 120 MCQs, +4 / −1, English only (2026 bulletin). One paper for the whole subject group.

Source: icar.org.in.

Checked against the exam body's published information. Formats and fees change; confirm the current edition there before you book.

Engineering Thermodynamics in ICAR AIEEA-PG

Unit III sets single-answer MCQs across the whole subject: definitions (intensive/extensive, quasi-static, path functions), statements of the zeroth, first and second laws, Carnot efficiency and COP, polytropic-process relations, steam-table terms (dryness fraction, critical point, Mollier chart), air-standard efficiency formulas and comparisons, VCR components and the tonne of refrigeration, and psychrometric definitions. Negative marking rewards exact definitions and quick one-step calculations.

Energy, work, heat and the cycles behind engines, refrigerators and dryers.

Our 96 ICAR AIEEA-PG questions in this subject: 34 easy, 41 medium, 21 hard, across 9 units.

10 practice questions, worked

Choose an answer, then open the working. Each explanation says why the right answer is right and why the others are not.

These 10 were written to ICAR AIEEA-PG and are not shown on any other exam's page.

Question 1 · easy

Which description fits a closed system (control mass)?

  1. Energy may cross its boundary as heat or work, but no mass crosses it
  2. Neither mass nor energy in any form is allowed to cross its boundary
  3. Mass may flow across its boundary, but heat and work transfers cannot
  4. Mass and energy both cross its boundary freely, as in a running pump
Answer and working

A. Energy may cross its boundary as heat or work, but no mass crosses it

A closed system has a fixed mass; heat and work can still cross its boundary. Allowing neither mass nor energy describes an isolated system, and mass flowing across the boundary (as in a pump) makes it an open system or control volume.

Question 2 · easy

The zeroth law of thermodynamics provides the basis for

  1. the conservation of energy in every process
  2. measuring temperature with a thermometer
  3. the direction in which heat flows unaided
  4. the absolute zero of the entropy scale
Answer and working

B. measuring temperature with a thermometer

The zeroth law says two bodies each in thermal equilibrium with a third are in equilibrium with each other; the thermometer is that third body, so the law makes temperature measurement meaningful. Energy conservation is the first law, the direction of heat flow is the second law, and the entropy reference is the third law.

Question 3 · easy

A closed system receives 150 kJ of heat and does 60 kJ of work on its surroundings. The change in its internal energy is

  1. +210 kJ
  2. −90 kJ
  3. +90 kJ
  4. +60 kJ
Answer and working

C. +90 kJ

ΔU = Q − W = 150 − 60 = +90 kJ (heat in positive, work by the system positive). +210 kJ adds the work instead of subtracting it, −90 kJ reverses both signs, and +60 kJ confuses work with energy change.

Question 4 · easy

Enthalpy is defined as

  1. H = U − PV
  2. H = Q − W
  3. H = U + TS
  4. H = U + PV
Answer and working

D. H = U + PV

Enthalpy is H = U + PV, the combination that appears in constant-pressure and flow processes. U − PV has no standard meaning, Q − W is the change in U from the first law, and U + TS is not a standard function (the Helmholtz function is U − TS).

Question 5 · medium

Steam enters an adiabatic nozzle at negligible velocity and its enthalpy falls by 200 kJ/kg. The exit velocity is about

  1. 447 m/s
  2. 20.0 m/s
  3. 632 m/s
  4. 14.1 m/s
Answer and working

C. 632 m/s

V2 = √(2Δh) with Δh in J/kg: √(2 × 200 000) = 632 m/s. 447 m/s drops the factor 2, 20.0 m/s forgets to convert kJ to J, and 14.1 m/s makes both mistakes.

Question 6 · easy

For a reversible process, the area under the process curve on a T–s diagram represents

  1. the work done during the process
  2. the change in enthalpy in the process
  3. the change in internal energy
  4. the heat transferred during the process
Answer and working

D. the heat transferred during the process

For a reversible process δQ = T ds, so ∫T ds is the heat. Work is the area under a P–v curve; enthalpy and internal energy changes are not, in general, areas under a T–s line.

Question 7 · hard

A heat-pump dryer delivers heat at 60 °C while drawing heat from air at 10 °C and has a measured COP of 3.5. Its second-law (exergetic) efficiency relative to a Carnot heat pump between the same temperatures is about

  1. 62 %
  2. 53 %
  3. 292 %
  4. 15 %
Answer and working

B. 53 %

COP_HP,Carnot = TH/(TH − TL) = 333.15/50 = 6.66; η_II = 3.5/6.66 = 53 %. 62 % uses the refrigerator Carnot COP TL/(TH − TL), 292 % uses Celsius temperatures (60/50), and 15 % is the Carnot engine efficiency between the two temperatures, not a heat-pump comparison.

Question 8 · hard

On a Mollier (h–s) chart, constant-pressure lines inside the wet region are straight because

  1. enthalpy of wet steam does not depend on its dryness fraction at a given pressure
  2. entropy of wet steam does not change during boiling at a constant pressure
  3. their slope ∂h/∂s at constant pressure equals the saturation temperature, which is constant there
  4. the chart is drawn on logarithmic axes that straighten all curves in that region
Answer and working

C. their slope ∂h/∂s at constant pressure equals the saturation temperature, which is constant there

From T ds = dh − v dP, at constant pressure dh/ds = T; in the wet region T = Tsat is constant, so the lines are straight. Enthalpy and entropy both change with quality during boiling, and the Mollier chart uses linear axes.

Question 9 · hard

If the evaporator temperature of a cold store is lowered while the condensing temperature stays the same, the COP of the plant

  1. increases, because the stored produce is now held at a lower temperature
  2. decreases, because compressor work per kg rises and refrigerating effect falls
  3. remains the same, because the condenser conditions have not been changed
  4. increases, because the refrigerant density at suction becomes higher
Answer and working

B. decreases, because compressor work per kg rises and refrigerating effect falls

A lower evaporator pressure means a larger pressure ratio (more work per kg) and, usually, a smaller refrigerating effect, so COP falls — as the Carnot COP TL/(TH − TL) also shows. Suction vapour density actually falls, reducing capacity.

Question 10 · medium

Air at 30 °C has a vapour pressure of 2.0 kPa. The saturation pressure of water at 30 °C is 4.247 kPa. The relative humidity is about

  1. 2.0 %
  2. 212 %
  3. 47.1 %
  4. 46.0 %
Answer and working

C. 47.1 %

φ = pv/psat = 2.0/4.247 = 47.1 %. 2.0 % divides by barometric pressure, 212 % inverts the ratio, and 46.0 % is the degree of saturation W/Ws, which is close to but not the same as relative humidity.

A study plan for Engineering Thermodynamics in ICAR AIEEA-PG

This plan follows where our questions actually fall, so the time goes where the marks are likely to be. It is our reading of the syllabus, not the exam body's weighting.

  1. First, the heavy units (36% of the 96 questions): Second law, entropy and the Carnot cycle (13, 14%); Air-standard cycles: Otto, Diesel, dual and Brayton (11, 11%); First law of thermodynamics (11, 11%).

    Read the manual chapters for these first and do every worked question you can find on them.

  2. Then the middle band: Introduction to psychrometry (11, 11%); Properties of steam, steam tables and the Mollier chart (11, 11%); Vapour-compression cycle basics (11, 11%).

    Aim for one sitting per unit, then mixed questions across them.

  3. Then the lighter units: Ideal gas processes (10, 10%); Systems, properties and the zeroth law (10, 10%); Steady-flow energy equation (8, 8%).

    Learn the definitions, classifications and standard numbers; these units are more often recalled than worked.

  4. Leave time for the hard ones: Air-standard cycles: Otto, Diesel, dual and Brayton (4 hard of 11), Second law, entropy and the Carnot cycle (4 hard of 13), Ideal gas processes (3 hard of 10).

    Come back to these after a first pass, untimed, and read every explanation, including for the options you rejected.

  5. Bank the easy marks: Systems, properties and the zeroth law (6 easy of 10); First law of thermodynamics (6 easy of 11).

    Do these early in revision so they are fast on the day.

  6. Finish timed. Sit the subject as a timed set without notes, mark it, and send each wrong answer back to its unit above.

Last updated · How Laisha writes and checks its pages · Report a mistake

Ask Laisha about this

Opens Laisha's chat with your question ready to send. Sign in or start free.

Unlock every question — ICAR AIEEA-PG Engineering Thermodynamics

US$10 a month · one price worldwide · cancel any time

  • Every practice question in this subject, with full working
  • Timed exam papers and progress by unit
  • Ask Laisha to explain any answer — up to 1,000 questions a month
Free or Smarter
FreeSmarter
Grow guides, pest pages, articlesRead allRead all
Ask Laisha5 a dayUp to 1,000 a month
Exam practiceThe sample on each pageEvery question, timed papers
Crop calendar and pest alerts—For your own fields
Calculators and tools—All
Uploads and reports—100 a month, real files
10 days free for every new account, no card.