LAISHA
Open Laisha

ICAR AIEEA-PG Machine Design: practice questions

ICAR AIEEA-PG — Agricultural Engineering & Technology (Major Subject Group 10) · India · National Testing Agency for ICAR

Original practice questions written to the published syllabus · not past papers
10worked here, free
87written to this exam in this subject
13syllabus units

About ICAR AIEEA-PG

ICAR AIEEA-PG — Agricultural Engineering & Technology (Major Subject Group 10) is a postgraduate admission exam run by National Testing Agency for ICAR, for candidates in India. Computer-based, 120 minutes, 120 MCQs, +4 / −1, English only (2026 bulletin). One paper for the whole subject group.

Source: icar.org.in.

Checked against the exam body's published information. Formats and fees change; confirm the current edition there before you book.

Machine Design in ICAR AIEEA-PG

Units III and IV (theory of machines, strength of materials) and Unit V (farm machinery): definitions, theories of failure, stress concentration, key and coupling types, bearing life, spring formulas and short calculations.

Sizing the parts of farm machines so they do not fail: shafts, keys, joints, springs, bearings, drives and overload devices.

Our 87 ICAR AIEEA-PG questions in this subject: 39 easy, 38 medium, 10 hard, across 13 units.

10 practice questions, worked

Choose an answer, then open the working. Each explanation says why the right answer is right and why the others are not.

These 10 were written to ICAR AIEEA-PG and are not shown on any other exam's page.

Question 1 · easy

A shaft is specified in AISI/SAE 1045 steel. What does the designation tell the designer?

  1. It is a free-cutting steel with 4.5 per cent sulphur
  2. It is a plain carbon steel with about 0.45 per cent carbon
  3. It is an alloy steel with 10 per cent nickel and 0.45 per cent chromium
  4. It has a tensile strength of about 1045 MPa
Answer and working

B. It is a plain carbon steel with about 0.45 per cent carbon

In the AISI/SAE four-digit system, the first two digits (10) mean plain carbon steel and the last two give carbon content in hundredths of a per cent (45, so about 0.45 per cent). The number is not a strength, and sulphurised free-cutting grades are in the 11xx series.

Question 2 · easy

A ductile steel part with a sharp groove carries only a steady load. How is stress concentration normally treated in its design?

  1. It is applied as Kf, because Kf is usually larger than Kt
  2. It is always applied in full, as Kt times the nominal stress, because a ductile part fails at the notch peak
  3. It is usually neglected
  4. It is applied to the modulus of elasticity rather than the stress
Answer and working

C. It is usually neglected

Under static load a ductile material yields locally at the notch and the load spreads to the surrounding material, so the peak stress does not cause failure; stress concentration is normally ignored. It must be applied for brittle materials and for all materials under fatigue loading. Kf is never larger than Kt. The reason is that local yielding at the notch redistributes the stress.

Question 3 · medium

Which material behaviour is correct for fatigue design?

  1. Steels usually show an endurance limit, while aluminium alloys have no true endurance limit
  2. No metal has an endurance limit; all fail eventually at any stress
  3. An endurance limit exists only under compressive stress
  4. Aluminium alloys have an endurance limit of about half their ultimate strength, just as wrought steels do
Answer and working

A. Steels usually show an endurance limit, while aluminium alloys have no true endurance limit

The S-N curve of steel flattens beyond roughly 10^6 to 10^7 cycles, giving an endurance limit. Aluminium and most non-ferrous alloys keep falling, so a fatigue strength at a stated life (for example 5 x 10^8 cycles) is used. The 0.5 Sut estimate applies to wrought steel.

Question 4 · hard

A 12 mm x 12 mm square key fixes a pulley to a 48 mm shaft transmitting 400 N m. Allowable stresses for the key are 60 MPa in shear and 100 MPa in crushing. What minimum key length is required?

  1. 27.8 mm
  2. 13.9 mm
  3. 55.6 mm
  4. 23.1 mm
Answer and working

A. 27.8 mm

Shear: T = tau w l d/2, so l = 2T/(tau w d) = 2 x 400000/(60 x 12 x 48) = 23.1 mm. Crushing: T = sigma c (h/2) l d/2, so l = 4T/(sigma c h d) = 4 x 400000/(100 x 12 x 48) = 27.8 mm. The key must satisfy both, so l = 27.8 mm. 23.1 mm checks shear only. 13.9 mm drops one of the halves (2T/(sigma c h d)); 55.6 mm enters the 24 mm radius in place of d.

Question 5 · medium

A knuckle joint carries an axial tensile load of 50 kN. The allowable shear stress in the pin is 60 MPa. What is the minimum pin diameter?

  1. 20.4 mm
  2. 32.6 mm
  3. 23.0 mm
  4. 16.3 mm
Answer and working

C. 23.0 mm

The knuckle pin is in double shear: P = 2 (pi/4) d^2 tau, so d = sqrt(2P/(pi tau)) = sqrt(2 x 50000/(pi x 60)) = 23.0 mm. Treating it as single shear gives 32.6 mm; dropping the 2 from sqrt(2P/(pi tau)) gives 16.3 mm; taking the pin area as d^2 gives 20.4 mm. The pin must also be checked for bending and bearing.

Question 6 · easy

Why is a cotter given a small taper?

  1. So that driving it in draws the parts tightly together and friction holds it in place
  2. To allow the rods to rotate relative to each other
  3. To make it act as a spring under load, so the joint can absorb shock from the two rods
  4. So that it can carry bending moments
Answer and working

A. So that driving it in draws the parts tightly together and friction holds it in place

The taper converts the driving force into an axial pull that tightens the joint, and a small taper keeps the cotter from loosening under friction. It does not make the joint carry bending or permit rotation; a knuckle joint does the latter.

Question 7 · medium

A helical spring with 10 active coils, wire diameter 6 mm and mean coil diameter 48 mm carries 500 N. Take G = 80 GPa. What is its deflection?

  1. 60.8 mm
  2. 42.7 mm
  3. 51.2 mm
  4. 21.3 mm
Answer and working

B. 42.7 mm

delta = 8 P D^3 N/(G d^4) = 8 x 500 x 48^3 x 10/(80000 x 6^4) = 42.7 mm. Using 12 total coils (active plus two end coils) instead of 10 active coils gives 51.2 mm; the end coils do not deflect. Using the outer coil diameter (54 mm) gives 60.8 mm, and using 4 instead of 8 in the formula halves the answer to 21.3 mm.

Question 8 · easy

Why is the spring index (D/d) of helical springs usually kept between about 4 and 12?

  1. An index above 12 always makes the Wahl factor greater than 2
  2. The index affects only the colour of the heat treatment
  3. Below 4 the spring has no stiffness at all, and above 12 its stiffness becomes infinite, so it cannot deflect under load
  4. Low indices are hard to coil and have high curvature stress; high indices tend to buckle and tangle
Answer and working

D. Low indices are hard to coil and have high curvature stress; high indices tend to buckle and tangle

A small index means sharply curved wire: difficult to coil and a large Wahl correction. A large index gives a floppy spring prone to buckling and tangling in handling. Stiffness varies continuously with the index, and the Wahl factor approaches 1 as the index grows.

Question 9 · easy

For 20-degree full-depth involute teeth the Lewis form factor (module basis) is approximately Y = 0.484 - 2.87/z. What is Y for a 20-tooth pinion?

  1. 0.108
  2. 0.627
  3. 0.197
  4. 0.340
Answer and working

D. 0.340

Y = 0.484 - 2.87/20 = 0.484 - 0.1435 = 0.340. 0.108 is the circular-pitch form y (Y = pi y). 0.627 adds the terms; 0.197 misplaces the decimal (2.87/10 = 0.287).

Question 10 · easy

A strain gauge on the surface of a steel drawbar, aligned with a uniaxial stress, reads 400 microstrain. Take E = 200 GPa. What is the stress?

  1. 80000 MPa
  2. 0.08 MPa
  3. 500 MPa
  4. 80 MPa
Answer and working

D. 80 MPa

sigma = E epsilon = 200000 MPa x 400 x 10^-6 = 80 MPa. 80000 MPa keeps E in GPa and drops the micro prefix (200 x 400); 0.08 MPa uses E in GPa (200 x 400 x 10^-6); 500 MPa divides E by the reading (200000/400).

A study plan for Machine Design in ICAR AIEEA-PG

This plan follows where our questions actually fall, so the time goes where the marks are likely to be. It is our reading of the syllabus, not the exam body's weighting.

  1. First, the heavy units (52% of the 87 questions): Belt and chain drives (11, 13%); Keys and couplings (9, 10%); The design process, materials and factor of safety (9, 10%); Springs (8, 9%); Spur gear design (Lewis and Buckingham) (8, 9%).

    Read the manual chapters for these first and do every worked question you can find on them.

  2. Then the middle band: Shafts under combined bending and torsion (7, 8%); Stress concentration and fatigue (Goodman and Soderberg) (7, 8%); Knuckle and cotter joints (6, 7%); Rolling and sliding bearings and bearing life (6, 7%); Welded joints (6, 7%).

    Aim for one sitting per unit, then mixed questions across them.

  3. Then the lighter units: Overload safety devices: shear bolts and slip clutches (5, 6%); Measurement of force, torque and strain on machine elements (3, 3%); Bolted joints (2, 2%).

    Learn the definitions, classifications and standard numbers; these units are more often recalled than worked.

  4. Leave time for the hard ones: Keys and couplings (3 hard of 9), Shafts under combined bending and torsion (2 hard of 7), Overload safety devices: shear bolts and slip clutches (1 hard of 5).

    Come back to these after a first pass, untimed, and read every explanation, including for the options you rejected.

  5. Bank the easy marks: The design process, materials and factor of safety (6 easy of 9); Measurement of force, torque and strain on machine elements (2 easy of 3).

    Do these early in revision so they are fast on the day.

  6. Finish timed. Sit the subject as a timed set without notes, mark it, and send each wrong answer back to its unit above.

Last updated · How Laisha writes and checks its pages · Report a mistake

Ask Laisha about this

Opens Laisha's chat with your question ready to send. Sign in or start free.

Unlock every question — ICAR AIEEA-PG Machine Design

US$10 a month · one price worldwide · cancel any time

  • Every practice question in this subject, with full working
  • Timed exam papers and progress by unit
  • Ask Laisha to explain any answer — up to 1,000 questions a month
Free or Smarter
FreeSmarter
Grow guides, pest pages, articlesRead allRead all
Ask Laisha5 a dayUp to 1,000 a month
Exam practiceThe sample on each pageEvery question, timed papers
Crop calendar and pest alerts—For your own fields
Calculators and tools—All
Uploads and reports—100 a month, real files
10 days free for every new account, no card.