LAISHA
Open Laisha

ICAR AICE-JRF/SRF Machine Design: practice questions

ICAR AICE-JRF/SRF (PhD) — Agricultural Engineering subjects 38–43 · India · National Testing Agency for ICAR

Original practice questions written to the published syllabus · not past papers
10worked here, free
43written to this exam in this subject
13syllabus units

About ICAR AICE-JRF/SRF

ICAR AICE-JRF/SRF (PhD) — Agricultural Engineering subjects 38–43 is a PhD, fellowship and lectureship exam run by National Testing Agency for ICAR, for candidates in India. LAN-based computer test, 2 hours, 120 MCQs: 20 Part A (general knowledge and reasoning), 50 Part B (core group), 50 Part C (specialisation); four options.

Source: icar.org.in.

Checked against the exam body's published information. Formats and fees change; confirm the current edition there before you book.

Machine Design in ICAR AICE-JRF/SRF

Design of farm machine components at postgraduate depth: fatigue under variable soil loads, Goodman and Soderberg design, bearing selection, overload protection, and measurement of force, torque and strain for design data.

Sizing the parts of farm machines so they do not fail: shafts, keys, joints, springs, bearings, drives and overload devices.

Our 43 ICAR AICE-JRF/SRF questions in this subject: 1 easy, 20 medium, 22 hard, across 13 units.

10 practice questions, worked

Choose an answer, then open the working. Each explanation says why the right answer is right and why the others are not.

These 10 were written to ICAR AICE-JRF/SRF and are not shown on any other exam's page.

Question 1 · hard

At a point in a ductile part the in-plane principal stresses are 120 MPa (tension) and 40 MPa (compression); the third principal stress is zero. The yield strength is 320 MPa. What is the factor of safety by the maximum shear stress (Tresca) theory?

  1. 2.00
  2. 4.00
  3. 2.67
  4. 2.22
Answer and working

A. 2.00

Tresca: yield when sigma1 - sigma3 reaches Syt. With principal stresses 120, 0 and -40 MPa, the largest difference is 120 - (-40) = 160 MPa (maximum shear 80 MPa against Syt/2 = 160 MPa), so N = 320/160 = 2.00. Using only the largest principal stress gives 2.67 (Rankine). Von Mises, sqrt(sigma1^2 - sigma1 sigma2 + sigma2^2) = 144.2 MPa, gives 2.22. Adding the stresses algebraically (80 MPa) is not a failure theory. 4.00 divides Syt by the maximum shear stress (320/80) instead of comparing it with Syt/2.

Question 2 · hard

A solid shaft of 50 mm diameter is to be replaced by a hollow shaft of the same material with inner diameter half the outer diameter, carrying the same torque at the same maximum shear stress. What outer diameter is needed?

  1. 53.3 mm
  2. 55.0 mm
  3. 51.1 mm
  4. 50.0 mm
Answer and working

C. 51.1 mm

Equal strength: d^3 = do^3 (1 - k^4), so do = 50/(1 - 0.5^4)^(1/3) = 50/(0.9375)^(1/3) = 51.1 mm. Using (1 - k^2) gives 55.0 mm, and forgetting the cube root gives 53.3 mm. The hollow shaft weighs about 78 per cent of the solid one.

Question 3 · medium

The hitch pin of a trailed implement is a clevis-and-pin (knuckle-type) joint. In service the pin bends and wears oval. Which statement about its design is correct?

  1. Only double shear matters, because pins never fail in bending
  2. A single-shear calculation gives the correct diameter because the drawbar is one plate, and bending can be neglected in a short pin
  3. The pin must be checked for bending and bearing as well as double shear, and it should be secured so it cannot work out
  4. A loose fit is preferred because it reduces bending stress
Answer and working

C. The pin must be checked for bending and bearing as well as double shear, and it should be secured so it cannot work out

In a clevis the pin acts as a short beam between the fork prongs, so bending often governs; bearing pressure causes the oval wear seen. Double shear is also checked. Clearance increases bending and impact, and the securing clip matters because a lost pin causes run-away implements.

Question 4 · hard

A bolt is preloaded to 10 kN. The bolt stiffness is 200 kN/mm and the stiffness of the clamped parts is 800 kN/mm. An external tensile load of 6 kN is then applied to the joint. What is the bolt load?

  1. 11.2 kN
  2. 16.0 kN
  3. 10.0 kN
  4. 14.8 kN
Answer and working

A. 11.2 kN

Joint constant C = kb/(kb + km) = 200/(200+800) = 0.2. Bolt load = Fi + C P = 10 + 0.2 x 6 = 11.2 kN. Adding the whole load (16 kN) ignores the stiff members; 14.8 kN applies the member share to the bolt. The clamping force falls to 5.2 kN.

Question 5 · hard

Why are welded steel details in fatigue design codes often assessed on stress range alone, with little or no correction for mean stress?

  1. Welding leaves tensile residual stresses near yield, so the local mean stress is already high whatever the applied mean
  2. Weld metal has no endurance limit
  3. Mean stress has no effect on any metal's fatigue life
  4. Welds are always left in residual compression after cooling, so the applied mean stress can never open a crack at the weld toe
Answer and working

A. Welding leaves tensile residual stresses near yield, so the local mean stress is already high whatever the applied mean

Shrinkage of the weld as it cools locks in tensile residual stress of the order of the yield strength near the toe. The effective mean stress is therefore high regardless of the applied load, and the applied stress range governs crack growth. Mean stress does matter for unwelded parts, and welds are not left in compression.

Question 6 · medium

A belt has a maximum allowable tension of 1800 N and a mass of 0.6 kg/m. At what belt speed does it transmit maximum power?

  1. 54.8 m/s
  2. 1000 m/s
  3. 38.7 m/s
  4. 31.6 m/s
Answer and working

D. 31.6 m/s

Maximum power occurs when Tc = Tmax/3, i.e. m v^2 = Tmax/3, so v = sqrt(Tmax/(3m)) = sqrt(1800/(3 x 0.6)) = 31.6 m/s. sqrt(Tmax/m) = 54.8 m/s is the speed where all tension is centrifugal and no power is transmitted. 1000 m/s forgets the square root (1800/1.8); 38.7 m/s sets Tc = Tmax/2.

Question 7 · hard

A 20-tooth pinion meshes externally with a 40-tooth gear; module 4 mm, face width 40 mm, and load-stress factor K = 1.2 N/mm^2. What is Buckingham's wear strength Sw = b Q dp K?

  1. 5120 N
  2. 10240 N
  3. 3840 N
  4. 2560 N
Answer and working

A. 5120 N

Q = 2 zg/(zg + zp) = 2 x 40/60 = 1.333; dp = m zp = 80 mm. Sw = 40 x 1.333 x 80 x 1.2 = 5120 N. Using zp in the numerator of Q gives 2560 N; using the gear diameter gives 10240 N. 3840 N takes Q = 1, ignoring the ratio factor.

Question 8 · medium

A baler drive normally sees peak working torques up to 250 N m. The gearbox is damaged above 600 N m. The designer wants the shear bolt to break at 1.4 times the peak working torque. Is this setting acceptable?

  1. Yes: it breaks at 350 N m, above normal peaks and below the damaging 600 N m
  2. No: a shear bolt must break at exactly the working torque of 250 N m
  3. Yes, but only if the bolt is designed with an allowable stress of 429 MPa
  4. No: it breaks at 350 N m, which is above the gearbox limit
Answer and working

A. Yes: it breaks at 350 N m, above normal peaks and below the damaging 600 N m

Break torque = 1.4 x 250 = 350 N m. This lies above the normal peaks (no nuisance breaks) and below 600 N m (the gearbox is protected). Setting it at the working torque would break the bolt in normal use.

Question 9 · easy

Which transducer is widely used in tillage research to measure the horizontal (draft) and vertical forces on a soil-engaging tool?

  1. The extended octagonal ring transducer with strain gauges
  2. A tachogenerator
  3. A thermocouple
  4. A Bourdon tube pressure gauge
Answer and working

A. The extended octagonal ring transducer with strain gauges

The extended octagonal ring, fitted with strain gauges at nodes that respond selectively to horizontal and vertical force, separates draft and vertical load and can also give moment. A Bourdon tube measures fluid pressure, a thermocouple temperature and a tachogenerator speed.

Question 10 · hard

A knuckle joint pin is often analysed for bending by assuming a load distribution between two limiting cases. Why?

  1. Because the pin is always in single shear
  2. Because the pin carries no bending in practice
  3. Because bending is only checked for compressive loads
  4. The actual pressure distribution along the pin depends on fit and deflection, so the true bending moment lies between the uniformly distributed and the concentrated-load cases
Answer and working

D. The actual pressure distribution along the pin depends on fit and deflection, so the true bending moment lies between the uniformly distributed and the concentrated-load cases

With a clearance fit the load is concentrated near the edges of the eye and fork; with a tight fit it is spread. Textbooks take a moment between these limits, commonly a mean of the two cases, and size the pin accordingly. The pin does bend, is in double shear, and the joint carries tension.

A study plan for Machine Design in ICAR AICE-JRF/SRF

This plan follows where our questions actually fall, so the time goes where the marks are likely to be. It is our reading of the syllabus, not the exam body's weighting.

  1. First, the heavy units (58% of the 43 questions): Measurement of force, torque and strain on machine elements (7, 16%); Overload safety devices: shear bolts and slip clutches (5, 12%); Stress concentration and fatigue (Goodman and Soderberg) (5, 12%); Bolted joints (4, 9%); Rolling and sliding bearings and bearing life (4, 9%).

    Read the manual chapters for these first and do every worked question you can find on them.

  2. Then the middle band: Spur gear design (Lewis and Buckingham) (4, 9%); Welded joints (3, 7%); Belt and chain drives (2, 5%); Keys and couplings (2, 5%); Knuckle and cotter joints (2, 5%).

    Aim for one sitting per unit, then mixed questions across them.

  3. Then the lighter units: Shafts under combined bending and torsion (2, 5%); The design process, materials and factor of safety (2, 5%); Springs (1, 2%).

    Learn the definitions, classifications and standard numbers; these units are more often recalled than worked.

  4. Leave time for the hard ones: Springs (1 hard of 1), Bolted joints (3 hard of 4), Welded joints (2 hard of 3).

    Come back to these after a first pass, untimed, and read every explanation, including for the options you rejected.

  5. Bank the easy marks: Measurement of force, torque and strain on machine elements (1 easy of 7).

    Do these early in revision so they are fast on the day.

  6. Finish timed. Sit the subject as a timed set without notes, mark it, and send each wrong answer back to its unit above.

Last updated · How Laisha writes and checks its pages · Report a mistake

Ask Laisha about this

Opens Laisha's chat with your question ready to send. Sign in or start free.

Unlock every question — ICAR AICE-JRF/SRF Machine Design

US$10 a month · one price worldwide · cancel any time

  • Every practice question in this subject, with full working
  • Timed exam papers and progress by unit
  • Ask Laisha to explain any answer — up to 1,000 questions a month
Free or Smarter
FreeSmarter
Grow guides, pest pages, articlesRead allRead all
Ask Laisha5 a dayUp to 1,000 a month
Exam practiceThe sample on each pageEvery question, timed papers
Crop calendar and pest alerts—For your own fields
Calculators and tools—All
Uploads and reports—100 a month, real files
10 days free for every new account, no card.