ICAR AICE-JRF/SRF (PhD) — Agricultural Engineering subjects 38–43 · India · National Testing Agency for ICAR
Original practice questions written to the published syllabus · not past papersICAR AICE-JRF/SRF (PhD) — Agricultural Engineering subjects 38–43 is a PhD, fellowship and lectureship exam run by National Testing Agency for ICAR, for candidates in India. LAN-based computer test, 2 hours, 120 MCQs: 20 Part A (general knowledge and reasoning), 50 Part B (core group), 50 Part C (specialisation); four options.
Source: icar.org.in.
Checked against the exam body's published information. Formats and fees change; confirm the current edition there before you book.
Unit 6 soil dynamics in tillage and traction at PG depth: Mohr-Coulomb and soil-metal friction, soil failure and critical depth, Reece's equation, Bekker and Janosi-Hanamoto models, mobility numbers, compaction models.
How soil resists tools and supports wheels: draft, slip, tractive efficiency, weight transfer and stability.
Our 53 ICAR AICE-JRF/SRF questions in this subject: 2 easy, 26 medium, 25 hard, across 13 units.
Choose an answer, then open the working. Each explanation says why the right answer is right and why the others are not.
These 10 were written to ICAR AICE-JRF/SRF and are not shown on any other exam's page.
Which field instrument measures both the pressure-sinkage relationship and the shear stress-displacement relationship of a soil for vehicle mobility work?
B. Bevameter
The bevameter combines a sinkage plate test (Bekker's kc, kφ, n) with a shear ring test (c, φ, K). The cone penetrometer gives a single composite cone index; the Proctor and Casagrande devices are laboratory tests for compaction and consistency.
Why does the draft of most tillage tools rise with travel speed?
B. Soil moved by the tool must be accelerated, adding an inertial force that grows with speed
The inertial term, proportional to the mass rate of soil moved times its velocity change, rises roughly with speed squared. This is why the ASABE draft equation includes an S² term for implements like the mouldboard plough.
A tractor carries 20 kN on its drive wheels on dry sand (c = 0, φ = 30°). What is the maximum thrust the soil can provide?
D. 11.55 kN
H = A·c + W tan φ; with c = 0, H = 20 × tan 30° = 11.55 kN. Contact area does not matter in dry sand. Using sin φ gives 10.00 kN. 34.64 kN divides by tan φ; 17.32 kN uses cos φ.
In Bekker's pressure-sinkage equation p = (kc/b + kφ)zⁿ, b is
D. the smaller dimension of the contact area
Bekker used the smaller dimension of the loading area; kc is the cohesive modulus and kφ the frictional modulus of deformation. For a tyre, b is the contact width.
A tyre operates at net traction ratio 0.4, motion resistance ratio 0.08 and slip 10 %. What is its tractive efficiency?
C. 75.0 %
TE = (1 − s) × NTR/(NTR + MRR) = 0.90 × 0.4/0.48 = 75.0 %. GTR = NTR + MRR; subtracting MRR instead gives an efficiency above the true value. 83.3 % omits the (1 − s) term; 112.5 % comes from subtracting MRR (0.4/0.32); 8.3 % multiplies by s instead of (1 − s).
A longer track contact length, at the same load and width, develops a given thrust at lower slip because
D. shear displacement accumulates along the contact length, mobilising soil shear strength sooner
Shear displacement j at a point grows with its distance from the front of the contact (j = s·x). A long contact mobilises more of the soil's shear strength at a given slip, so thrust builds at lower slip.
A penetrometer using the 130 mm² cone records 260 N at 10 cm depth. A colleague mistakenly uses the 323 mm² base area. By what factor does the colleague underestimate the cone index?
A. 2.48
Correct CI = 260/130×10⁻⁶ = 2.0 MPa; with the wrong area 260/323×10⁻⁶ = 0.805 MPa. Ratio = 323/130 = 2.48. CI scales with 1/area, not with the square or square root. 0.40 inverts the ratio; 6.17 squares it; 1.58 takes its square root.
A tractor (track 1.4 m, CG height 0.8 m, CG on the centreline) turns on level ground on a 5 m radius. Above what speed will it begin to overturn outwards?
D. 23.6 km/h
Overturn when v²/(g r) = (t/2)/h → v = √(g r t/(2h)) = √(9.81 × 5 × 1.4/(2 × 0.8)) = 6.55 m/s = 23.6 km/h. Using full track in place of half gives 33.4 km/h; quoting m/s as km/h is a unit slip. 154.5 km/h forgets the square root (42.9 × 3.6).
On a 2WD tractor pulling a load on level ground in steady motion, the horizontal force balance gives
C. rear wheel net thrust = drawbar pull + front wheel rolling resistance
The rear tyres must overcome both the implement and the front wheels' rolling resistance. Gross thrust is larger still, since it also covers the rear wheels' own motion resistance.
In a three-point linkage, what is the virtual hitch point?
C. The point where the lines of the upper and lower links, extended, intersect in side view
The linkage acts as if the implement were hitched at the instantaneous centre where the extended link lines meet; its position determines how the implement's forces are transferred to the tractor.
This plan follows where our questions actually fall, so the time goes where the marks are likely to be. It is our reading of the syllabus, not the exam body's weighting.
Read the manual chapters for these first and do every worked question you can find on them.
Aim for one sitting per unit, then mixed questions across them.
Learn the definitions, classifications and standard numbers; these units are more often recalled than worked.
Come back to these after a first pass, untimed, and read every explanation, including for the options you rejected.
Do these early in revision so they are fast on the day.
Last updated · How Laisha writes and checks its pages · Report a mistake
US$10 a month · one price worldwide · cancel any time
| Free | Smarter | |
|---|---|---|
| Grow guides, pest pages, articles | Read all | Read all |
| Ask Laisha | 5 a day | Up to 1,000 a month |
| Exam practice | The sample on each page | Every question, timed papers |
| Crop calendar and pest alerts | — | For your own fields |
| Calculators and tools | — | All |
| Uploads and reports | — | 100 a month, real files |
An AI operating system for agriculture: free guides, manuals and tools written for every country.