LAISHA
Open Laisha

ICAR AICE-JRF/SRF Food & Dairy Engineering: practice questions

ICAR AICE-JRF/SRF (PhD) — Agricultural Engineering subjects 38–43 · India · National Testing Agency for ICAR

Original practice questions written to the published syllabus · not past papers
10worked here, free
59written to this exam in this subject
13syllabus units

About ICAR AICE-JRF/SRF

ICAR AICE-JRF/SRF (PhD) — Agricultural Engineering subjects 38–43 is a PhD, fellowship and lectureship exam run by National Testing Agency for ICAR, for candidates in India. LAN-based computer test, 2 hours, 120 MCQs: 20 Part A (general knowledge and reasoning), 50 Part B (core group), 50 Part C (specialisation); four options.

Source: icar.org.in.

Checked against the exam body's published information. Formats and fees change; confirm the current edition there before you book.

Food & Dairy Engineering in ICAR AICE-JRF/SRF

Subject 38 units on dairy and food engineering, evaporation and drying, thermal engineering and process equipment design go to PG depth: fouling mechanisms, ε-NTU, UHT direct versus indirect heating, multiple-effect feed arrangements, MVR and TVR, spray-drier balances and powder properties, homogeniser valve theory, disc-stack Σ theory, membrane flux decline and diafiltration, Plank's assumptions and hygienic design standards.

Unit operations of food and milk plants: balances, fluid flow, heat exchange, thermal processing, evaporation, separation, freezing and hygienic design.

Our 59 ICAR AICE-JRF/SRF questions in this subject: 0 easy, 39 medium, 20 hard, across 13 units.

10 practice questions, worked

Choose an answer, then open the working. Each explanation says why the right answer is right and why the others are not.

These 10 were written to ICAR AICE-JRF/SRF and are not shown on any other exam's page.

Question 1 · medium

Fouling of plate heat exchangers when milk is heated above about 70 °C is caused mainly by

  1. Lactose caramelisation
  2. Denatured β-lactoglobulin depositing with calcium phosphate
  3. Casein micelle dissociation in the cold regeneration sections
  4. Fat crystallisation
Answer and working

B. Denatured β-lactoglobulin depositing with calcium phosphate

β-lactoglobulin unfolds and aggregates above about 70 °C and deposits with calcium phosphate, whose solubility falls as temperature rises. Lactose browning is a minor factor; fat crystallises on cold, not hot, surfaces.

Question 2 · medium

D is 5 min at 110 °C and 0.5 min at 120 °C. The z value is

  1. 4.3 °C
  2. 2.2 °C
  3. 1 °C
  4. 10 °C
Answer and working

D. 10 °C

z = (T₂ − T₁)/log(D₁/D₂) = 10/log(10) = 10 °C. 4.3 °C uses the natural log (10/2.303); 1 °C divides by the ratio 10 instead of its log; 2.2 °C divides by the difference in D (10/4.5).

Question 3 · medium

Mechanical vapour recompression (MVR) differs from thermal vapour recompression (TVR) in that MVR

  1. Cannot be used on milk
  2. Uses an electrically driven compressor or fan instead of a steam jet ejector
  3. Operates without a condenser or vacuum
  4. Uses high-pressure motive steam from the boiler to entrain and compress the vapour
Answer and working

B. Uses an electrically driven compressor or fan instead of a steam jet ejector

TVR compresses part of the vapour with a steam ejector; MVR compresses vapour mechanically, giving very high equivalent economies and shifting energy use from steam to electricity.

Question 4 · hard

Heating 10,052 kg/h of dry air (H = 0.010) from 20 to 200 °C, with humid heat 1.005 + 1.88 H kJ/kg K, requires about

  1. 572 kW
  2. 1.85 × 10⁶ kW
  3. 505 kW
  4. 515 kW
Answer and working

D. 515 kW

c_s = 1.005 + 0.0188 = 1.024 kJ/kg K; Q = 10,052 × 1.024 × 180/3600 = 514.6 kW. Ignoring moisture in the air gives 505 kW; forgetting the /3600 gives 1.85 × 10⁶, a figure in kJ/h; 572 kW uses the final 200 °C instead of the 180 K rise.

Question 5 · medium

Compared with spray-dried milk powder, roller (drum) dried milk powder typically has

  1. Lower solubility and more heat-induced flavour and colour
  2. Higher solubility and a whiter colour, because heating is gentler
  3. No Maillard browning
  4. A lower bulk density and better wettability
Answer and working

A. Lower solubility and more heat-induced flavour and colour

Film on the hot drum reaches temperatures close to the drum surface, causing protein denaturation and browning. The caramelised flavour is valued in some chocolate, but solubility is lower.

Question 6 · hard

In a high-pressure valve homogeniser under industrial conditions, globule disruption is generally attributed mainly to

  1. Electrostatic repulsion
  2. Turbulent eddies in and just beyond the valve gap
  3. Enzymic action of lipase
  4. Gravity settling in the valve
Answer and working

B. Turbulent eddies in and just beyond the valve gap

Turbulence, cavitation and shear are all proposed; for typical industrial pressures and gaps, inertial forces in turbulent eddies are generally considered dominant.

Question 7 · medium

A solute is at 5.0 % in the feed and 0.2 % in the permeate. The observed rejection is

  1. 0.96
  2. 25
  3. 0.04
  4. 24
Answer and working

A. 0.96

R = 1 − C_p/C_f = 1 − 0.2/5.0 = 0.96. 0.04 is the passage (C_p/C_f). 25 is the concentration ratio C_f/C_p; 24 divides by the permeate instead of the feed ((5.0 − 0.2)/0.2).

Question 8 · hard

Using Plank's equation, a 5 cm thick slab (ρ = 1000 kg/m³, λ = 266.6 kJ/kg, T_f = −1.5 °C, frozen k = 1.5 W/m K) frozen in air at −30 °C takes 2.7 h with h = 30 W/m² K. Doubling the surface heat transfer coefficient from 30 to 60 W/m² K (all else equal) gives a freezing time of about

  1. 2.7 h
  2. 1.35 h
  3. 0.54 h
  4. 1.6 h
Answer and working

D. 1.6 h

Surface term halves: 0.5 × 0.05/60 = 4.17e-4; internal term unchanged at 2.08e-4; sum = 6.25e-4; t = 9,354,000 × 6.25e-4 = 5850 s = 1.6 h. It does not halve (1.35 h) because the internal conduction term is unchanged. 2.7 h assumes h has no effect; 0.54 h keeps only the internal conduction term.

Question 9 · hard

Using Plank's equation, a 5 cm thick slab (ρ = 1000 kg/m³, λ = 266.6 kJ/kg, T_f = −1.5 °C, frozen k = 1.5 W/m K) frozen in air at −30 °C with h = 30 W/m² K takes 2.7 h. Doubling the thickness to 10 cm, all else unchanged, gives a freezing time of about

  1. 10.8 h
  2. 6.5 h
  3. 5.4 h
  4. 4.9 h
Answer and working

B. 6.5 h

Pa/h doubles (1.67e-3) and Ra²/k quadruples (8.33e-4); sum 2.5e-3; t = 9,354,000 × 2.5e-3 = 23,390 s = 6.5 h. It lies between doubling (5.4 h) and quadrupling (10.8 h). 4.9 h doubles only the surface term and leaves the internal term unchanged.

Question 10 · hard

A dairy wants to lower its CIP caustic temperature to save energy. According to Sinner's principle, which change best keeps cleaning performance?

  1. Replace the final rinse with a shorter pre-rinse
  2. Extend circulation time and/or raise detergent concentration, then verify by ATP swabs and inspection
  3. Skip the acid step
  4. Lower the flow velocity to save pump energy as well, since slower flow gives longer contact with the soil
Answer and working

B. Extend circulation time and/or raise detergent concentration, then verify by ATP swabs and inspection

Lowering one factor (temperature) must be compensated by others (time, chemical, mechanical action), and any change must be validated. Lowering velocity cuts mechanical action further; skipping steps leaves soil or mineral.

A study plan for Food & Dairy Engineering in ICAR AICE-JRF/SRF

This plan follows where our questions actually fall, so the time goes where the marks are likely to be. It is our reading of the syllabus, not the exam body's weighting.

  1. First, the heavy units (47% of the 59 questions): Centrifugation and cream separation (6, 10%); Spray and drum drying (6, 10%); Thermal processing kinetics: D, z and F values (6, 10%); Cleaning-in-place and sanitary design (5, 8%); Evaporation: single and multiple effect (5, 8%).

    Read the manual chapters for these first and do every worked question you can find on them.

  2. Then the middle band: Filtration and membrane processes: MF, UF, NF and RO (5, 8%); Pasteurisation: HTST and LTLT (5, 8%); UHT processing and sterilisation (5, 8%); Freezing and Plank's equation (4, 7%); Homogenisation (4, 7%).

    Aim for one sitting per unit, then mixed questions across them.

  3. Then the lighter units: Heat exchangers: plate, tubular and scraped-surface (3, 5%); Material and energy balances (3, 5%); Fluid flow in food plants: pumps, pipes and rheology (2, 3%).

    Learn the definitions, classifications and standard numbers; these units are more often recalled than worked.

  4. Leave time for the hard ones: Spray and drum drying (3 hard of 6), Thermal processing kinetics: D, z and F values (3 hard of 6), Freezing and Plank's equation (2 hard of 4).

    Come back to these after a first pass, untimed, and read every explanation, including for the options you rejected.

  5. Finish timed. Sit the subject as a timed set without notes, mark it, and send each wrong answer back to its unit above.

Last updated · How Laisha writes and checks its pages · Report a mistake

Ask Laisha about this

Opens Laisha's chat with your question ready to send. Sign in or start free.

Unlock every question — ICAR AICE-JRF/SRF Food & Dairy Engineering

US$10 a month · one price worldwide · cancel any time

  • Every practice question in this subject, with full working
  • Timed exam papers and progress by unit
  • Ask Laisha to explain any answer — up to 1,000 questions a month
Free or Smarter
FreeSmarter
Grow guides, pest pages, articlesRead allRead all
Ask Laisha5 a dayUp to 1,000 a month
Exam practiceThe sample on each pageEvery question, timed papers
Crop calendar and pest alerts—For your own fields
Calculators and tools—All
Uploads and reports—100 a month, real files
10 days free for every new account, no card.