LAISHA
Open Laisha

GATE Machine Design: practice questions

GATE — Agricultural Engineering (AG) · India · IITs and IISc on rotation (2027: IIT Madras)

Original practice questions written to the published syllabus · not past papers
10worked here, free
88written to this exam in this subject
13syllabus units

About GATE

GATE — Agricultural Engineering (AG) is a postgraduate admission exam run by IITs and IISc on rotation (2027: IIT Madras), for candidates in India. Computer-based, 3 hours, 100 marks (15 General Aptitude + 85 technical: 25 one-mark and 30 two-mark questions). MCQ, MSQ and NAT; negative marking on MCQ only (−1/3 for one-mark, −2/3 for two-mark); no partial credit on MSQ. On-screen virtual calculator.

Source: gate2027.iitm.ac.in.

Checked against the exam body's published information. Formats and fees change; confirm the current edition there before you book.

Machine Design in GATE

Section 2 names machine design. Numerical and NAT items recur on belt drives (tension ratio, power, centrifugal tension, V-belt wedge), spur gear strength (Lewis, tangential force, module), shear pin diameter for a given breaking torque, chain drives and shaft sizing under combined bending and torsion. Expect one or two machine design calculations each year.

Sizing the parts of farm machines so they do not fail: shafts, keys, joints, springs, bearings, drives and overload devices.

Our 88 GATE questions in this subject: 19 easy, 43 medium, 26 hard, across 13 units.

10 practice questions, worked

Choose an answer, then open the working. Each explanation says why the right answer is right and why the others are not.

These 10 were written to GATE and are not shown on any other exam's page.

Question 1 · easy

Steel with a tensile yield strength of 400 MPa is used for a part in pure shear. According to the distortion energy theory, what is its yield strength in shear?

  1. 400 MPa
  2. 200 MPa
  3. 283 MPa
  4. 231 MPa
Answer and working

D. 231 MPa

Distortion energy theory gives Ssy = Syt / sqrt(3) = 0.577 x 400 = 231 MPa. 200 MPa is the maximum shear stress theory value (0.5 Syt). 283 MPa is 400 / sqrt(2), which is not a failure theory result.

Question 2 · hard

A steel link has a stress amplitude of 100 MPa and a mean stress of 150 MPa. Its corrected endurance limit is 250 MPa, yield strength 400 MPa and ultimate strength 600 MPa. What is the factor of safety by the Goodman criterion?

  1. 1.92
  2. 1.29
  3. 1.54
  4. 2.50
Answer and working

C. 1.54

Goodman: 1/N = sigma a/Se + sigma m/Sut = 100/250 + 150/600 = 0.400 + 0.250 = 0.650, so N = 1.54. Soderberg uses Syt: 1/N = 0.400 + 0.375, N = 1.29. Gerber (parabola) gives 1.92. Se/sigma a = 2.50 ignores the mean stress.

Question 3 · hard

A steel link has a stress amplitude of 100 MPa and a mean stress of 150 MPa. Its corrected endurance limit is 250 MPa, yield strength 400 MPa and ultimate strength 600 MPa. What is the factor of safety by the Soderberg criterion?

  1. 1.54
  2. 1.60
  3. 6.67
  4. 1.29
Answer and working

D. 1.29

Soderberg: 1/N = sigma a/Se + sigma m/Syt = 100/250 + 150/400 = 0.400 + 0.375 = 0.775, so N = 1.29. Using Sut (Goodman) gives 1.54. Syt/(sigma a + sigma m) = 1.60 is only the first-cycle yield check. Multiplying the ratios instead of adding them is an algebra slip: 1/(0.400 x 0.375) = 6.67.

Question 4 · medium

A tractor PTO delivers 15 kW at 540 rpm to an implement. What torque does the PTO shaft carry?

  1. 265 N m
  2. 27.8 N m
  3. 531 N m
  4. 4.42 N m
Answer and working

A. 265 N m

T = 60 P / (2 pi n) = 60 x 15000 / (2 pi x 540) = 265 N m. Dividing power by rpm directly gives 27.8, and forgetting the factor 60 (treating n as rev/s) gives 4.42 N m. 531 N m drops the 2 from 2 pi n (60 x 15000/(pi x 540)).

Question 5 · medium

Why does a high preload improve the fatigue life of a bolt in a joint under fluctuating external load?

  1. Preload makes the bolt stiffer than the clamped members, so the bolt safely carries a larger share of the load change
  2. Preload removes the stress concentration at the thread root
  3. The stiff clamped members absorb most of the load fluctuation, so the alternating stress in the bolt is small
  4. Preload raises the endurance limit of the bolt material
Answer and working

C. The stiff clamped members absorb most of the load fluctuation, so the alternating stress in the bolt is small

With preload, only the fraction C = kb/(kb + km) of the external load change reaches the bolt while the joint stays closed, so the bolt's stress amplitude is small even though its mean stress is high. Preload does not change material properties or thread geometry, and it does not change stiffnesses.

Question 6 · hard

A shaft of 60 mm diameter is welded to a plate by a circumferential fillet weld of 6 mm leg and carries a torque of 1 kN m. What is the shear stress in the weld throat?

  1. 41.7 MPa
  2. 20.8 MPa
  3. 29.5 MPa
  4. 23.6 MPa
Answer and working

A. 41.7 MPa

Throat t = 0.707 x 6 = 4.24 mm. For a thin ring of throat t at radius d/2, J = pi t d^3/4 and tau = T (d/2)/J = 2T/(pi t d^2) = 2 x 10^6/(pi x 4.24 x 60^2) = 41.7 MPa. Using the leg size gives 29.5 MPa; dropping the 2 in 2T/(pi t d^2) gives 20.8 MPa; 16T/(pi d^3) = 23.6 MPa is the stress in the solid shaft, not the weld.

Question 7 · hard

A roller chain of 15.875 mm pitch connects sprockets of 17 and 51 teeth at a centre distance of 635 mm. The centre distance can be adjusted slightly, and the chain length is to be rounded up as recommended for roller chains. What chain length, in links, should be used?

  1. 116 links
  2. 76 links
  3. 115 links
  4. 150 links
Answer and working

A. 116 links

Ln = 2C/p + (z1 + z2)/2 + ((z2 - z1)/(2 pi))^2 p/C = 80.0 + 34 + 0.73 = 114.73, rounded up to the next even number, 116, to avoid an offset link. Rounding up to 115 links, an odd number, would need an offset (cranked) link, which is weaker; forgetting to halve (z1 + z2) gives 148.73, rounded up to 150 links, and using C/p instead of 2C/p gives 74.73, rounded up to 76.

Question 8 · easy

A spur gear has 40 teeth and a pitch circle diameter of 160 mm. What is its module, and what is the usual textbook choice of face width?

  1. 4 mm; about 4 mm
  2. 40 mm; about 400 mm
  3. 0.25 mm; about 2.5 mm
  4. 4 mm; about 40 mm
Answer and working

D. 4 mm; about 40 mm

m = d/z = 160/40 = 4 mm. Face width is usually taken as about 10 m (range about 9.5 m to 12.5 m), so about 40 mm. 0.25 is z/d, the inverse.

Question 9 · medium

A single active strain gauge (quarter bridge) with gauge factor 2.0 is excited at 5 V. The part strains by 1000 microstrain. What is the approximate bridge output?

  1. 10 mV
  2. 5 mV
  3. 2.5 mV
  4. 1.25 mV
Answer and working

C. 2.5 mV

Quarter bridge: Vo = V GF epsilon/4 = 5 x 2.0 x 0.001/4 = 0.0025 V = 2.5 mV. A full bridge of four active gauges gives about 10 mV, a half bridge 5 mV. 1.25 mV omits the gauge factor.

Question 10 · hard

Four active strain gauges in a full Wheatstone bridge, each with gauge factor 2.0, measure a strain of 1000 microstrain (two gauges in tension, two in compression, arranged so their outputs add). The excitation is 5 V. What is the approximate output?

  1. 40 mV
  2. 5 mV
  3. 10 mV
  4. 2.5 mV
Answer and working

C. 10 mV

For a full bridge with four equal active arms of alternating sign, Vo = V GF epsilon = 5 x 2.0 x 0.001 = 10 mV, four times a quarter bridge (2.5 mV). 40 mV multiplies the full-bridge value by 4 again.

A study plan for Machine Design in GATE

This plan follows where our questions actually fall, so the time goes where the marks are likely to be. It is our reading of the syllabus, not the exam body's weighting.

  1. First, the heavy units (49% of the 88 questions): Belt and chain drives (11, 13%); Stress concentration and fatigue (Goodman and Soderberg) (9, 10%); Shafts under combined bending and torsion (8, 9%); Spur gear design (Lewis and Buckingham) (8, 9%); Rolling and sliding bearings and bearing life (7, 8%).

    Read the manual chapters for these first and do every worked question you can find on them.

  2. Then the middle band: The design process, materials and factor of safety (7, 8%); Bolted joints (6, 7%); Measurement of force, torque and strain on machine elements (6, 7%); Overload safety devices: shear bolts and slip clutches (6, 7%); Springs (6, 7%).

    Aim for one sitting per unit, then mixed questions across them.

  3. Then the lighter units: Keys and couplings (5, 6%); Knuckle and cotter joints (5, 6%); Welded joints (4, 5%).

    Learn the definitions, classifications and standard numbers; these units are more often recalled than worked.

  4. Leave time for the hard ones: Keys and couplings (3 hard of 5), Bolted joints (3 hard of 6), Spur gear design (Lewis and Buckingham) (3 hard of 8).

    Come back to these after a first pass, untimed, and read every explanation, including for the options you rejected.

  5. Bank the easy marks: The design process, materials and factor of safety (4 easy of 7); Keys and couplings (2 easy of 5).

    Do these early in revision so they are fast on the day.

  6. Finish timed. Sit the subject as a timed set without notes, mark it, and send each wrong answer back to its unit above.

Last updated · How Laisha writes and checks its pages · Report a mistake

Ask Laisha about this

Opens Laisha's chat with your question ready to send. Sign in or start free.

Unlock every question — GATE Machine Design

US$10 a month · one price worldwide · cancel any time

  • Every practice question in this subject, with full working
  • Timed exam papers and progress by unit
  • Ask Laisha to explain any answer — up to 1,000 questions a month
Free or Smarter
FreeSmarter
Grow guides, pest pages, articlesRead allRead all
Ask Laisha5 a dayUp to 1,000 a month
Exam practiceThe sample on each pageEvery question, timed papers
Crop calendar and pest alerts—For your own fields
Calculators and tools—All
Uploads and reports—100 a month, real files
10 days free for every new account, no card.