GATE — Agricultural Engineering (AG) · India · IITs and IISc on rotation (2027: IIT Madras)
Original practice questions written to the published syllabus · not past papersGATE — Agricultural Engineering (AG) is a postgraduate admission exam run by IITs and IISc on rotation (2027: IIT Madras), for candidates in India. Computer-based, 3 hours, 100 marks (15 General Aptitude + 85 technical: 25 one-mark and 30 two-mark questions). MCQ, MSQ and NAT; negative marking on MCQ only (−1/3 for one-mark, −2/3 for two-mark); no partial credit on MSQ. On-screen virtual calculator.
Source: gate2027.iitm.ac.in.
Checked against the exam body's published information. Formats and fees change; confirm the current edition there before you book.
Numerical answer and MCQ items on seed-drill, planter and fertiliser-drill calibration (one of the most often repeated topics), rotary-tiller bite length, mouldboard plough draft and power, offset disc harrow force balance, field capacity, and machinery cost by straight-line, declining-balance and sum-of-years-digits depreciation with break-even custom hire.
Machines that prepare the seedbed and put seed and fertiliser in the ground, and how to calibrate and cost them.
Our 44 GATE questions in this subject: 8 easy, 29 medium, 7 hard, across 14 units.
Choose an answer, then open the working. Each explanation says why the right answer is right and why the others are not.
These 10 were written to GATE and are not shown on any other exam's page.
A mounted mouldboard plough keeps rising out of work in firm soil even with the hydraulic set deep. Which fault is the most likely mechanical cause?
C. Worn shares that have lost their vertical suction
Worn share points lose the downward suction that pulls the bottom in, and the plough floats out. A small change in speed does not make a plough float out; polished mouldboards help scouring, and horizontal suction affects width, not depth.
Chisel shanks set too far apart for their working depth will most likely
C. leave ridges of untilled soil between the shanks
The loosened zones from adjacent shanks must meet below the surface. If spacing is too large for the depth, untilled ridges remain between shanks.
A tractor with a 2.0 m wheelbase exerts a horizontal drawbar pull of 12 kN at a drawbar height of 0.5 m. What weight is transferred from the front to the rear axle (simple static approximation)?
B. 3.0 kN
Taking moments about the rear wheel contact: ΔW = P·h/L = 12 × 0.5 / 2.0 = 3.0 kN. Inverting the ratio gives 48 kN; multiplying P by h alone gives 6.0 kN·m, a moment, not a force; using (L − h) as the arm gives 9.0 kN.
In a horizontal-plate planter, what is the function of the spring-loaded cut-off?
D. Remove excess seeds so each cell carries one seed
The cut-off wipes surplus seeds from the cell; the knock-out or ejector pushes the seed from the cell into the tube.
A planter's ground wheel is 50 cm in diameter and drives a 12-cell plate at 0.5 plate turns per wheel turn. Ignoring skid, what is seed spacing?
D. 26.18 cm
Spacing = πD/(i·N) = π × 0.5/(0.5 × 12) = 0.2618 m = 26.18 cm. Multiplying by i gives 6.54 cm; ignoring the drive ratio gives 13.09 cm; leaving out π (using D as the travel per turn) gives 8.33 cm.
Which opener is best suited to sowing through heavy surface residue?
A. Double-disc opener
Discs cut through residue instead of dragging it; tined, hoe and shoe openers bunch residue and block.
Why must adjacent passes of a spinning-disc broadcaster overlap?
D. The spread pattern tapers toward the edges, so overlap evens out the total
A single-pass pattern is heaviest in the centre and thins at the edges; spacing passes at the correct bout width overlaps the tails to give even coverage.
How many turns of a 1.2 m diameter drive wheel are needed to simulate 1/25 ha with an 11-row drill at 20 cm spacing, taking effective travel per turn as πD(1 − 0.05)?
D. 50.8
Width = 11 × 0.2 = 2.2 m. Travel per turn = π × 1.2 × 0.95 = 3.581 m. Area per turn = 7.879 m². N = 400/7.879 = 50.8 turns. Ignoring skid gives 48.2; using one row gives 558. 101.5 uses the 1.2 m as a radius (π × 0.6 × 0.95).
A farm must sow 40 ha within 10 days of 8 working hours each, at 5 km/h and 80 % field efficiency. What minimum effective width is needed?
C. 1.25 m
Hours = 80. Required EFC = 40/80 = 0.5 ha/h. w = 10 × 0.5/(5 × 0.8) = 1.25 m. Omitting the factor 10 gives 0.125 m; ignoring efficiency gives 1.00 m.
Owning a zero-till drill costs 60 000 per year fixed plus 900 per hectare variable. Custom hire costs 2400 per hectare. Above what annual area is owning cheaper?
D. 40 ha
Break-even area = FC/(custom rate − VC) = 60 000/(2400 − 900) = 40 ha. Ignoring variable cost gives 25 ha; adding VC to the hire rate gives 18.2 ha. 66.7 ha divides by the variable cost alone (60 000/900).
This plan follows where our questions actually fall, so the time goes where the marks are likely to be. It is our reading of the syllabus, not the exam body's weighting.
Read the manual chapters for these first and do every worked question you can find on them.
Aim for one sitting per unit, then mixed questions across them.
Learn the definitions, classifications and standard numbers; these units are more often recalled than worked.
Come back to these after a first pass, untimed, and read every explanation, including for the options you rejected.
Do these early in revision so they are fast on the day.
Last updated · How Laisha writes and checks its pages · Report a mistake
US$10 a month · one price worldwide · cancel any time
| Free | Smarter | |
|---|---|---|
| Grow guides, pest pages, articles | Read all | Read all |
| Ask Laisha | 5 a day | Up to 1,000 a month |
| Exam practice | The sample on each page | Every question, timed papers |
| Crop calendar and pest alerts | — | For your own fields |
| Calculators and tools | — | All |
| Uploads and reports | — | 100 a month, real files |
An AI operating system for agriculture: free guides, manuals and tools written for every country.