LAISHA
Open Laisha

ASRB NET Farm Machinery & Equipment I — Tillage, Sowing, Planting, Fertiliser: practice questions

ASRB NET — Farm Machinery & Power / Land & Water Management Engineering / Agricultural Structures & Process Engineering · India · Agricultural Scientists Recruitment Board (ICAR)

Original practice questions written to the published syllabus · not past papers
10worked here, free
34written to this exam in this subject
13syllabus units

About ASRB NET

ASRB NET — Farm Machinery & Power / Land & Water Management Engineering / Agricultural Structures & Process Engineering is a specialist certification exam run by Agricultural Scientists Recruitment Board (ICAR), for candidates in India. NET: 150 MCQs, 150 marks, 2 hours, −1/3 per wrong answer, English/Hindi, PG level. Combined NET/ARS/SMS/STO recruitment runs prelims, mains and interview.

Official site: pw.live.

We have not been able to confirm these details against the exam body's own specification, so fees, dates and pass marks are left out on purpose. Check the current format, eligibility, fees and dates on the official site.

Farm Machinery & Equipment I — Tillage, Sowing, Planting, Fertiliser in ASRB NET

PG-level recall and reasoning across tillage and sowing machines, conservation tillage machinery, testing indices and machinery management.

Machines that prepare the seedbed and put seed and fertiliser in the ground, and how to calibrate and cost them.

Our 34 ASRB NET questions in this subject: 0 easy, 21 medium, 13 hard, across 13 units.

10 practice questions, worked

Choose an answer, then open the working. Each explanation says why the right answer is right and why the others are not.

These 10 were written to ASRB NET and are not shown on any other exam's page.

Question 1 · medium

Which set of three principles defines conservation agriculture as promoted by FAO?

  1. Deep ploughing, residue burning and monocropping of high-yielding varieties
  2. Zero tillage, herbicide use, irrigation
  3. Contour bunding, terracing, strip cropping
  4. Minimum soil disturbance, permanent soil cover, crop diversification
Answer and working

D. Minimum soil disturbance, permanent soil cover, crop diversification

FAO defines conservation agriculture by minimum mechanical soil disturbance, permanent organic soil cover and species diversification. Herbicides are often used in practice but are not a defining principle; bunding and terracing are soil conservation structures.

Question 2 · medium

What is a known soil-structure drawback of repeated rotary tillage at the same depth?

  1. Complete inversion of residue
  2. Formation of back furrows
  3. Over-pulverisation and a smeared compact layer at blade depth
  4. Increase in soil organic matter
Answer and working

C. Over-pulverisation and a smeared compact layer at blade depth

Rotary blades cut and throw soil finely, and repeated passes can break down aggregates and smear a pan at the blade tip depth, especially in wet soils. Rotary tillers mix rather than invert residue.

Question 3 · hard

In Reece's universal earthmoving equation for a blade, the term for the weight of soil moved varies with depth d as

  1. d
  2. d²
  3. d³
  4. it does not depend on depth
Answer and working

B. d²

The gravitational term is γ g d² Nγ w, proportional to depth squared, whereas cohesion, adhesion and surcharge terms are proportional to depth. This is why draft rises faster than linearly with depth in non-cohesive soils.

Question 4 · hard

A trailed plough is hitched so that, in plan view, the line of pull does not pass through its centre of resistance because the tractor tread is wider than the cut. What is the result?

  1. A side draft that the landside or furrow wheel must carry, adding friction and wear
  2. The plough runs deeper with lower draft, because the offset pull increases the suction
  3. Draft control is disabled
  4. No effect, because only the vertical plane matters
Answer and working

A. A side draft that the landside or furrow wheel must carry, adding friction and wear

When the line of pull misses the centre of resistance in plan, a lateral component (side draft) arises and is resisted by the landside or furrow wheel, raising friction and draft. Hitch adjustment seeks to minimise it.

Question 5 · hard

The critical width-to-depth ratio of about 1.27 for a stable furrow slice comes from requiring

  1. the centre of gravity of the leaning slice to lie over its lower edge on the previous slice
  2. the slice to be cut at the soil's angle of internal friction, so it shears cleanly along its base
  3. the unit draft to be at a minimum
  4. the mouldboard to be helicoidal
Answer and working

A. the centre of gravity of the leaning slice to lie over its lower edge on the previous slice

With the lean angle given by sinδ = a/b and the centre of gravity required over the base, (a/b)⁴ + (a/b)² ≤ 1, so a/b ≤ 0.786 and b/a ≥ 1.272. It is a geometric stability condition, not a strength or draft criterion.

Question 6 · medium

Ploughing much deeper than a mouldboard bottom is designed for, at the same width, usually causes

  1. better burial of residue
  2. poor inversion because the width-to-depth ratio falls too low
  3. lower unit draft
  4. wider furrow slices
Answer and working

B. poor inversion because the width-to-depth ratio falls too low

Deeper cutting at fixed width lowers b/a toward or below the stable limit, so slices stand on edge or fall back, burying residue poorly.

Question 7 · hard

In Kachman and Smith's planter indices, 'precision' is

  1. the percentage of singles
  2. the percentage of misses
  3. the coefficient of variation of spacings classified as singles
  4. the mean spacing divided by theoretical spacing, expressed as a percentage
Answer and working

C. the coefficient of variation of spacings classified as singles

Precision is the CV of spacings within the singles region (between 0.5X and 1.5X). The percentage of singles is the quality-of-feed index.

Question 8 · hard

Why do older, taller rice seedlings give poor results in a mat-type transplanter?

  1. They float because they are lighter, so the fork cannot push them into the puddled soil
  2. They increase row spacing
  3. They jam or are damaged by the picking fork and roots of old mats tear unevenly
  4. They reduce the lateral shift
Answer and working

C. They jam or are damaged by the picking fork and roots of old mats tear unevenly

Machines are designed around young seedlings of a given height; taller, older seedlings bend, tangle and are damaged, and thicker root mats tear irregularly, giving uneven seedlings per hill.

Question 9 · medium

Granules of different sizes in a blended fertiliser spread by a spinning disc tend to

  1. spread identically
  2. stick together and form cakes
  3. dissolve during spreading
  4. segregate, because larger, denser granules are thrown farther
Answer and working

D. segregate, because larger, denser granules are thrown farther

Throw distance depends on granule size, density and shape, so components of a blend land in different places and nutrients form stripes.

Question 10 · hard

In several European countries, trailing-shoe or injection methods are required for slurry application mainly to

  1. increase the spread width
  2. reduce the tractor's draft requirement
  3. reduce ammonia emission
  4. allow broadcasting over crops
Answer and working

C. reduce ammonia emission

Placing slurry in bands on or in the soil reduces the exposed surface area and ammonia volatilisation compared with splash-plate spreading.

A study plan for Farm Machinery & Equipment I — Tillage, Sowing, Planting, Fertiliser in ASRB NET

This plan follows where our questions actually fall, so the time goes where the marks are likely to be. It is our reading of the syllabus, not the exam body's weighting.

  1. First, the heavy units (47% of the 34 questions): Seed-metering mechanisms: fluted roller, cup, plate and pneumatic (4, 12%); Chisel plough and subsoiler (3, 9%); Disc plough (3, 9%); Forces on tillage tools, draft and hitching (3, 9%); Furrow openers (3, 9%).

    Read the manual chapters for these first and do every worked question you can find on them.

  2. Then the middle band: Harrows, cultivators and rotavators (3, 9%); Objectives and types of tillage (3, 9%); Paddy and vegetable transplanters (3, 9%); Cost analysis of implements (2, 6%); Fertiliser distributors (2, 6%).

    Aim for one sitting per unit, then mixed questions across them.

  3. Then the lighter units: Furrow geometry (2, 6%); Mouldboard plough (2, 6%); Seed drills and planters (1, 3%).

    Learn the definitions, classifications and standard numbers; these units are more often recalled than worked.

  4. Leave time for the hard ones: Chisel plough and subsoiler (2 hard of 3), Forces on tillage tools, draft and hitching (2 hard of 3), Cost analysis of implements (1 hard of 2).

    Come back to these after a first pass, untimed, and read every explanation, including for the options you rejected.

  5. Finish timed. Sit the subject as a timed set without notes, mark it, and send each wrong answer back to its unit above.

Last updated · How Laisha writes and checks its pages · Report a mistake

Ask Laisha about this

Opens Laisha's chat with your question ready to send. Sign in or start free.

Unlock every question — ASRB NET Farm Machinery & Equipment I — Tillage, Sowing, Planting, Fertiliser

US$10 a month · one price worldwide · cancel any time

  • Every practice question in this subject, with full working
  • Timed exam papers and progress by unit
  • Ask Laisha to explain any answer — up to 1,000 questions a month
Free or Smarter
FreeSmarter
Grow guides, pest pages, articlesRead allRead all
Ask Laisha5 a dayUp to 1,000 a month
Exam practiceThe sample on each pageEvery question, timed papers
Crop calendar and pest alerts—For your own fields
Calculators and tools—All
Uploads and reports—100 a month, real files
10 days free for every new account, no card.