ICAR AIEEA-PG — Agricultural Engineering & Technology (Major Subject Group 10) · India · National Testing Agency for ICAR
Original practice questions written to the published syllabus · not past papersICAR AIEEA-PG — Agricultural Engineering & Technology (Major Subject Group 10) is a postgraduate admission exam run by National Testing Agency for ICAR, for candidates in India. Computer-based, 120 minutes, 120 MCQs, +4 / −1, English only (2026 bulletin). One paper for the whole subject group.
Source: icar.org.in.
Checked against the exam body's published information. Formats and fees change; confirm the current edition there before you book.
Recall of implement parts and functions (plough bottoms, suction, disc and tilt angles, metering devices, openers), classification of tillage, transplanter features, and short calculations of field capacity, seed rate and cost.
Machines that prepare the seedbed and put seed and fertiliser in the ground, and how to calibrate and cost them.
Our 50 ICAR AIEEA-PG questions in this subject: 9 easy, 40 medium, 1 hard, across 15 units.
Choose an answer, then open the working. Each explanation says why the right answer is right and why the others are not.
These 10 were written to ICAR AIEEA-PG and are not shown on any other exam's page.
Which mouldboard shape lays a sod furrow slice over with the least breaking?
C. Helicoidal (sod or breaker) mouldboard
A long, gently twisted helicoidal mouldboard turns the slice over slowly with little pulverising, suiting sod. A cylindrical, steep mouldboard breaks and pulverises the slice; slatted boards reduce contact in sticky soils.
The disc angle of a disc plough is the angle between
B. the plane of the disc edge and the direction of travel, in the horizontal plane
Disc angle is measured horizontally from the direction of travel; tilt angle is measured between the disc plane and the vertical. Confusing the two is the usual error.
A chisel plough differs from a mouldboard plough mainly in that it
C. shatters and loosens soil without inverting it
Chisel shanks loosen and shatter soil and leave residue on the surface, which is why they suit conservation tillage. Mouldboards invert; rotary tillers need PTO drive.
Subsoiling a hardpan is most effective when the soil at working depth is
A. dry enough to shatter
Dry, brittle subsoil fractures and loosens around the tine. Wet subsoil deforms plastically, so the tine cuts a slot and smears the walls with little loosening.
Why are zero-till drills built with heavier frames and stronger openers than drills for a tilled seedbed?
C. They must cut residue and penetrate untilled, firmer soil
Untilled soil is stronger and covered with residue, so openers need more down-force and robust construction.
Why do pneumatic (vacuum) meters handle ungraded seed better than cell plates?
C. Seeds are held on holes by suction, so seed size need not match a cell
Suction holds a seed on each hole regardless of small variations in shape, and a singulator removes doubles, so exact grading matters less than for a fixed cell.
In a central-hopper air seeder, how is seed divided among many rows?
D. A single meter feeds an air stream that a distribution head splits into hoses
Air seeders meter centrally and blow seed to a distribution head that divides it among the row hoses, allowing very wide machines.
Most mechanical rice transplanters require seedlings raised as
B. a mat nursery
The picking fork cuts blocks from a mat, so seedlings must be grown densely on a thin soil layer forming a mat. The roots interlock so the mat holds together when the fork cuts it.
At 30 mm exposed flute length a fluted-roller drill delivers 120 kg/ha. Assuming delivery proportional to exposed length, what length gives 100 kg/ha?
A. 25 mm
Length ∝ rate: 30 × 100/120 = 25 mm. Inverting the ratio gives 36 mm, which would increase the rate. The proportional assumption fails at short exposures, so recheck by calibration. 5 mm is the reduction (30 × 20/120), not the new length; 10 mm subtracts the 20 kg/ha change as if it were millimetres.
Using interest on average investment, what is the annual interest charge on an implement costing 400 000 with salvage value 40 000 at 10 % interest?
A. 22,000
Average investment = (400 000 + 40 000)/2 = 220 000; interest = 220 000 × 0.10 = 22,000. Charging on full price gives 40,000; using (P − S)/2 gives 18,000. 44,000 adds P and S without halving.
This plan follows where our questions actually fall, so the time goes where the marks are likely to be. It is our reading of the syllabus, not the exam body's weighting.
Read the manual chapters for these first and do every worked question you can find on them.
Aim for one sitting per unit, then mixed questions across them.
Learn the definitions, classifications and standard numbers; these units are more often recalled than worked.
Come back to these after a first pass, untimed, and read every explanation, including for the options you rejected.
Do these early in revision so they are fast on the day.
Last updated · How Laisha writes and checks its pages · Report a mistake
US$10 a month · one price worldwide · cancel any time
| Free | Smarter | |
|---|---|---|
| Grow guides, pest pages, articles | Read all | Read all |
| Ask Laisha | 5 a day | Up to 1,000 a month |
| Exam practice | The sample on each page | Every question, timed papers |
| Crop calendar and pest alerts | — | For your own fields |
| Calculators and tools | — | All |
| Uploads and reports | — | 100 a month, real files |
An AI operating system for agriculture: free guides, manuals and tools written for every country.