LAISHA
Open Laisha

ICAR AIEEA-PG Theory of Machines: practice questions

ICAR AIEEA-PG — Agricultural Engineering & Technology (Major Subject Group 10) · India · National Testing Agency for ICAR

Original practice questions written to the published syllabus · not past papers
10worked here, free
83written to this exam in this subject
12syllabus units

About ICAR AIEEA-PG

ICAR AIEEA-PG — Agricultural Engineering & Technology (Major Subject Group 10) is a postgraduate admission exam run by National Testing Agency for ICAR, for candidates in India. Computer-based, 120 minutes, 120 MCQs, +4 / −1, English only (2026 bulletin). One paper for the whole subject group.

Source: icar.org.in.

Checked against the exam body's published information. Formats and fees change; confirm the current edition there before you book.

Theory of Machines in ICAR AIEEA-PG

Unit III names theory of machines: definitions (pairs, inversions, isochronism, hunting, interference, creep), standard formulas and short calculations across all topics. Speed and accuracy on formula recall pay.

How mechanisms move and transmit power: linkages, cams, gears, belts, flywheels, governors, balancing and vibration.

Our 83 ICAR AIEEA-PG questions in this subject: 30 easy, 40 medium, 13 hard, across 12 units.

10 practice questions, worked

Choose an answer, then open the working. Each explanation says why the right answer is right and why the others are not.

These 10 were written to ICAR AIEEA-PG and are not shown on any other exam's page.

Question 1 · medium

A four-bar chain has links of 30 mm, 45 mm, 50 mm and 70 mm, and the 30 mm link is fixed. What motion is possible?

  1. Double-crank, because the shortest link is fixed
  2. No link makes a full rotation: every inversion is a triple-rocker
  3. Crank-rocker with the 45 mm link as crank
  4. Double-crank, because 30 + 70 equals 45 + 50
Answer and working

B. No link makes a full rotation: every inversion is a triple-rocker

s + l = 30 + 70 = 100 mm; p + q = 45 + 50 = 95 mm. Since 100 > 95 the chain is non-Grashof, so no link can revolve fully whichever link is fixed. Fixing the shortest link gives a double-crank only for a Grashof chain; the sums are not equal.

Question 2 · easy

How many instantaneous centres of rotation does a six-link planar mechanism have?

  1. 6
  2. 12
  3. 30
  4. 15
Answer and working

D. 15

N = n(n - 1)/2 = 6 x 5/2 = 15. Forgetting to halve (each IC is shared by a pair of links) gives 30. 12 is simply 2n.

Question 3 · medium

A slider moves outward along a slotted link at 2 m/s relative to the link while the link rotates at a constant 5 rad/s. What is the magnitude of the Coriolis component of the slider's acceleration?

  1. 20 m/s²
  2. 10 m/s²
  3. 50 m/s²
  4. 0 m/s², because the link speed is constant
Answer and working

A. 20 m/s²

Coriolis acceleration = 2ωv = 2 x 5 x 2 = 20 m/s², directed perpendicular to the slot (the sliding velocity rotated 90° in the sense of ω). Dropping the factor 2 gives 10. Constant link speed removes tangential acceleration, not the Coriolis term, which exists whenever a point slides on a rotating link.

Question 4 · hard

A pair of 20° involute spur gears of module 6 mm has a path of contact of 35 mm. What is the contact ratio?

  1. 1.98
  2. 1.86
  3. 5.43
  4. 5.83
Answer and working

A. 1.98

Contact ratio = path of contact/base pitch; base pitch = πm cos φ = π x 6 x cos 20° = 17.71 mm, so CR = 35/17.71 = 1.98. Dividing the path (not the arc) by the circular pitch πm = 18.85 mm gives 1.86; using sin φ instead of cos φ in the base pitch gives 5.43; 5.83 is 35/m.

Question 5 · easy

A flat belt drive carries 1000 N on the tight side and 400 N on the slack side. Assuming the belt obeys Hooke's law and neglecting centrifugal tension, what was the initial tension?

  1. 600 N
  2. 1400 N
  3. 1000 N
  4. 700 N
Answer and working

D. 700 N

T0 = (T1 + T2)/2 = (1000 + 400)/2 = 700 N. 600 N is the effective pull T1 - T2; 1400 N is the sum. 1000 N is simply the tight-side tension.

Question 6 · medium

A chain sprocket has 20 teeth and the chain pitch is 12.7 mm. What is the pitch-circle diameter of the sprocket?

  1. 80.85 mm
  2. 81.18 mm
  3. 41.10 mm
  4. 80.18 mm
Answer and working

B. 81.18 mm

d = p/sin(180°/T) = 12.7/sin 9° = 12.7/0.1564 = 81.18 mm. pT/π = 80.85 mm treats the pitch as an arc on a circle, but the chain wraps as a polygon, so the chord formula is correct. Using 360°/T gives 41.10 mm. 80.18 mm uses tan 9° instead of sin 9°.

Question 7 · hard

Taken in order over one cycle, the areas between an engine's turning-moment curve and its mean-torque line represent +50, -20, +40, -60, +30 and -40 J. What is the maximum fluctuation of energy?

  1. 70 J
  2. 60 J
  3. 240 J
  4. 0 J
Answer and working

A. 70 J

Cumulative energy from the start of the cycle: E + 50, E + 30, E + 70, E + 10, E + 40, E. The maximum is E + 70 and the minimum is E (at the start and end), so ΔE = 70 J. 60 J is the largest single loop, a common trap; 240 J adds all areas; 0 J is only the net over the cycle.

Question 8 · easy

Which statement correctly contrasts a flywheel with a governor?

  1. A flywheel controls mean speed over many cycles; a governor smooths speed within each cycle
  2. Both control mean speed, the flywheel mechanically and the governor hydraulically through the fuel pump
  3. A flywheel limits speed fluctuation within each cycle; a governor controls mean speed as load changes
  4. A governor stores energy; a flywheel changes the fuel supply
Answer and working

C. A flywheel limits speed fluctuation within each cycle; a governor controls mean speed as load changes

A flywheel is an energy reservoir: it absorbs and releases energy during each cycle but has no effect on mean speed if the load changes permanently. A governor senses a sustained change in mean speed and adjusts the fuel supply.

Question 9 · medium

A shaft alone has a lowest transverse natural frequency of 30 Hz. With the shaft treated as massless, the rotor it carries would give 40 Hz. Using Dunkerley's formula, what is the natural frequency of the combined system?

  1. 35 Hz
  2. 24 Hz
  3. 70 Hz
  4. 50 Hz
Answer and working

B. 24 Hz

Dunkerley: 1/fn² = 1/30² + 1/40² = 0.001111 + 0.000625 = 0.001736, fn = 24 Hz. The combined frequency must be lower than either; averaging (35 Hz) or adding (70 Hz) cannot be right. 50 Hz is √(30² + 40²), the wrong combination.

Question 10 · medium

A single-plate clutch with both sides effective has friction surfaces of 300 mm outer and 200 mm inner diameter. The axial force is 4 kN and μ = 0.3. Assuming uniform wear, what torque can it transmit?

  1. 150 N m
  2. 300 N m
  3. 304 N m
  4. 600 N m
Answer and working

B. 300 N m

Uniform wear: T = nμW(R1 + R2)/2 = 2 x 0.3 x 4000 x (0.15 + 0.10)/2 = 300 N m. One surface only gives 150; the uniform-pressure value is 304 N m; using diameters as radii doubles the answer.

A study plan for Theory of Machines in ICAR AIEEA-PG

This plan follows where our questions actually fall, so the time goes where the marks are likely to be. It is our reading of the syllabus, not the exam body's weighting.

  1. First, the heavy units (49% of the 83 questions): Gears and gear trains: simple, compound and epicyclic (13, 16%); Flywheels and turning-moment diagrams (10, 12%); Free and forced vibrations and critical speed (10, 12%); Belt, rope and chain drives: tension ratio and power (8, 10%).

    Read the manual chapters for these first and do every worked question you can find on them.

  2. Then the middle band: Mechanisms, links, pairs and Grashof's law (8, 10%); Velocity and acceleration analysis (7, 8%); Cams and followers (6, 7%); Governors (6, 7%).

    Aim for one sitting per unit, then mixed questions across them.

  3. Then the lighter units: Balancing of rotating and reciprocating masses (5, 6%); Clutches (5, 6%); Brakes and dynamometers (3, 4%); Differential gear (2, 2%).

    Learn the definitions, classifications and standard numbers; these units are more often recalled than worked.

  4. Leave time for the hard ones: Brakes and dynamometers (1 hard of 3), Belt, rope and chain drives: tension ratio and power (2 hard of 8), Gears and gear trains: simple, compound and epicyclic (3 hard of 13).

    Come back to these after a first pass, untimed, and read every explanation, including for the options you rejected.

  5. Bank the easy marks: Differential gear (2 easy of 2); Brakes and dynamometers (2 easy of 3).

    Do these early in revision so they are fast on the day.

  6. Finish timed. Sit the subject as a timed set without notes, mark it, and send each wrong answer back to its unit above.

Last updated · How Laisha writes and checks its pages · Report a mistake

Ask Laisha about this

Opens Laisha's chat with your question ready to send. Sign in or start free.

Unlock every question — ICAR AIEEA-PG Theory of Machines

US$10 a month · one price worldwide · cancel any time

  • Every practice question in this subject, with full working
  • Timed exam papers and progress by unit
  • Ask Laisha to explain any answer — up to 1,000 questions a month
Free or Smarter
FreeSmarter
Grow guides, pest pages, articlesRead allRead all
Ask Laisha5 a dayUp to 1,000 a month
Exam practiceThe sample on each pageEvery question, timed papers
Crop calendar and pest alerts—For your own fields
Calculators and tools—All
Uploads and reports—100 a month, real files
10 days free for every new account, no card.