LAISHA
Open Laisha

ASRB NET Theory of Machines: practice questions

ASRB NET — Farm Machinery & Power / Land & Water Management Engineering / Agricultural Structures & Process Engineering · India · Agricultural Scientists Recruitment Board (ICAR)

Original practice questions written to the published syllabus · not past papers
10worked here, free
38written to this exam in this subject
11syllabus units

About ASRB NET

ASRB NET — Farm Machinery & Power / Land & Water Management Engineering / Agricultural Structures & Process Engineering is a specialist certification exam run by Agricultural Scientists Recruitment Board (ICAR), for candidates in India. NET: 150 MCQs, 150 marks, 2 hours, −1/3 per wrong answer, English/Hindi, PG level. Combined NET/ARS/SMS/STO recruitment runs prelims, mains and interview.

Official site: pw.live.

We have not been able to confirm these details against the exam body's own specification, so fees, dates and pass marks are left out on purpose. Check the current format, eligibility, fees and dates on the official site.

Theory of Machines in ASRB NET

Applied kinematics and dynamics of farm machines: tractor power train (clutch, gearbox, differential, final drive), balancing and vibration of rotating implements, dynamometers for tractor testing.

How mechanisms move and transmit power: linkages, cams, gears, belts, flywheels, governors, balancing and vibration.

Our 38 ASRB NET questions in this subject: 8 easy, 12 medium, 18 hard, across 11 units.

10 practice questions, worked

Choose an answer, then open the working. Each explanation says why the right answer is right and why the others are not.

These 10 were written to ASRB NET and are not shown on any other exam's page.

Question 1 · hard

A cam turning at 300 rpm lifts a follower 40 mm with cycloidal motion during 120° of cam rotation. What is the maximum acceleration of the follower?

  1. 44.4 m/s²
  2. 9.0 m/s²
  3. 56.5 m/s²
  4. 36.0 m/s²
Answer and working

C. 56.5 m/s²

For cycloidal motion a max = 2πhω²/θo² = 2π x 0.04 x 987.0/4.3865 = 56.5 m/s², reached at one quarter and three quarters of the lift, with zero acceleration at the ends. Dropping the 2π gives 9.0; 44.4 and 36.0 m/s² are the SHM and uniform-acceleration peaks.

Question 2 · easy

Why are double-helical (herringbone) gears used instead of single helical gears in some heavy drives?

  1. They give a larger speed ratio in one stage than a worm drive
  2. They allow shafts at right angles to be connected
  3. They eliminate the need for lubrication
  4. The opposite helices cancel the axial thrust that a single helical gear produces
Answer and working

D. The opposite helices cancel the axial thrust that a single helical gear produces

A single helical gear produces an axial force proportional to the tangential load and tan of the helix angle, which the bearings must carry. Two opposite helices cancel it. Right-angle intersecting shafts use bevel gears; large single-stage ratios use worms.

Question 3 · easy

One rear wheel of a vehicle with an open bevel differential is held stationary, while the differential cage turns at 150 rpm. What is the speed of the other wheel's half-shaft?

  1. 150 rpm
  2. 300 rpm
  3. 75 rpm
  4. 0 rpm
Answer and working

B. 300 rpm

N_left + N_right = 2N_cage gives 0 + N = 300 rpm: the free side turns at twice the cage speed. This is why a tractor with one wheel on a firm patch and one spinning in mud still makes no progress without a differential lock. 150 rpm assumes the free wheel runs at cage speed; 75 rpm halves it.

Question 4 · easy

When should a tractor operator disengage the differential lock?

  1. Before turning, because a locked axle resists turning and can cause loss of steering control
  2. Only when travelling in reverse, because the lock can shear the axle if driven backwards under load
  3. Before ploughing in wet soil, because the lock increases wheel slip when the ground is soft
  4. Whenever the PTO is engaged
Answer and working

A. Before turning, because a locked axle resists turning and can cause loss of steering control

The lock makes both rear wheels turn at the same speed, which is useful for traction in straight-line work on slippery ground but fights the different wheel paths on a turn. Operators' manuals therefore require it to be released before turning and when travelling at speed.

Question 5 · medium

A thresher drum has a residual unbalance equivalent to a 50 g mass at 250 mm radius. What rotating force does this unbalance exert on the bearings at 900 rpm?

  1. 10125 N
  2. 2.81 N
  3. 111 N
  4. 11.3 N
Answer and working

C. 111 N

F = mω²r = 0.05 x 94.25² x 0.25 = 111 N. Using rpm for ω gives 10125 N; using rev/s gives 2.81 N. The force rises with the square of speed, which is why a drum that is acceptable at low speed shakes badly at working speed. 11.3 N divides the correct force by g.

Question 6 · hard

A rigid fan rotor running at 3000 rpm is to be balanced to grade G6.3 under the ISO rotor-balancing standard, where the grade number is the permissible eccentricity times angular speed in mm/s. What is the permissible eccentricity of its centre of mass?

  1. 20.1 μm
  2. 126 μm
  3. 2.1 μm
  4. 6.3 μm
Answer and working

A. 20.1 μm

e x ω = 6.3 mm/s with ω = 314.2 rad/s, so e = 6.3/314.2 mm = 0.0201 mm = 20.1 μm. Using rev/s instead of rad/s gives 126 μm; using rpm gives 2.1 μm. Multiplying e by the rotor mass gives the permissible residual unbalance.

Question 7 · hard

A grain cleaner running at 1500 rpm is to be mounted on undamped springs so that only 10% of its unbalanced force reaches the floor. What static deflection of the springs is needed?

  1. 3.98 mm
  2. 4.37 mm
  3. 0.40 mm
  4. 172.7 mm
Answer and working

B. 4.37 mm

Undamped TR = 1/(r² - 1) = 0.1 gives r² = 11, r = 3.317. Running frequency = 25 Hz, so fn = 25/3.317 = 7.54 Hz. δ = g/(2πfn)² = 9.81/(47.36)² = 4.37 mm. Using r² = 10 (forgetting the minus one) gives 3.98 mm; setting the natural frequency equal to the running frequency gives 0.40 mm, which would put the machine at resonance; forgetting 2π gives a deflection far too large.

Question 8 · medium

Two rotors with moments of inertia 3 kg m² (rotor A) and 1 kg m² (rotor B) are at the ends of a uniform shaft 1.2 m long. Where is the node for torsional vibration?

  1. 0.3 m from rotor A
  2. 0.9 m from rotor A
  3. 0.6 m from rotor A
  4. 0.4 m from rotor A
Answer and working

A. 0.3 m from rotor A

Both parts of the shaft must give the same frequency: l_A I_A = l_B I_B with l_A + l_B = 1.2 m. So 3 l_A = 1 x (1.2 - l_A), l_A = 1.2/4 = 0.3 m. The node lies nearer the heavier rotor. 0.9 m is the distance from rotor B, the classic swap; 0.6 m assumes the node is always at mid-length.

Question 9 · hard

A single-plate clutch with both sides effective has friction surfaces of 300 mm outer and 200 mm inner diameter, an axial force of 4 kN and μ = 0.3. What torque does it transmit if uniform pressure is assumed, as for a new clutch?

  1. 300 N m
  2. 152 N m
  3. 360 N m
  4. 304 N m
Answer and working

D. 304 N m

Uniform pressure: T = n(2/3)μW(R1³ - R2³)/(R1² - R2²) = 2 x (2/3) x 0.3 x 4000 x (0.003375 - 0.001)/(0.0225 - 0.01) = 304 N m. This is slightly more than the uniform-wear value (300 N m), which is why uniform wear is the safe design assumption. Using the outer radius only gives 360 N m. 152 N m is the one-surface value.

Question 10 · hard

A clutch plate has an outer radius of 150 mm and an inner radius of 100 mm and carries an axial force of 4 kN. Assuming uniform wear, what is the maximum pressure on the lining?

  1. 84.9 kPa
  2. 127.3 kPa
  3. 101.9 kPa
  4. 12.7 kPa
Answer and working

B. 127.3 kPa

Uniform wear: p r = C and W = 2πC(R1 - R2), so C = 4000/(2π x 0.05) = 12732 N/m. The pressure is greatest at the inner radius: p max = C/R2 = 12732/0.10 = 127.3 kPa. 84.9 kPa is the minimum (at the outer radius); 101.9 kPa is the uniform-pressure value. 12.7 kPa is a factor-of-ten slip.

A study plan for Theory of Machines in ASRB NET

This plan follows where our questions actually fall, so the time goes where the marks are likely to be. It is our reading of the syllabus, not the exam body's weighting.

  1. First, the heavy units (53% of the 38 questions): Balancing of rotating and reciprocating masses (5, 13%); Clutches (5, 13%); Differential gear (5, 13%); Governors (5, 13%).

    Read the manual chapters for these first and do every worked question you can find on them.

  2. Then the middle band: Brakes and dynamometers (4, 11%); Free and forced vibrations and critical speed (4, 11%); Cams and followers (3, 8%); Gears and gear trains: simple, compound and epicyclic (3, 8%).

    Aim for one sitting per unit, then mixed questions across them.

  3. Then the lighter units: Flywheels and turning-moment diagrams (2, 5%); Belt, rope and chain drives: tension ratio and power (1, 3%); Mechanisms, links, pairs and Grashof's law (1, 3%).

    Learn the definitions, classifications and standard numbers; these units are more often recalled than worked.

  4. Leave time for the hard ones: Mechanisms, links, pairs and Grashof's law (1 hard of 1), Balancing of rotating and reciprocating masses (3 hard of 5), Clutches (3 hard of 5).

    Come back to these after a first pass, untimed, and read every explanation, including for the options you rejected.

  5. Bank the easy marks: Differential gear (2 easy of 5); Gears and gear trains: simple, compound and epicyclic (1 easy of 3).

    Do these early in revision so they are fast on the day.

  6. Finish timed. Sit the subject as a timed set without notes, mark it, and send each wrong answer back to its unit above.

Last updated · How Laisha writes and checks its pages · Report a mistake

Ask Laisha about this

Opens Laisha's chat with your question ready to send. Sign in or start free.

Unlock every question — ASRB NET Theory of Machines

US$10 a month · one price worldwide · cancel any time

  • Every practice question in this subject, with full working
  • Timed exam papers and progress by unit
  • Ask Laisha to explain any answer — up to 1,000 questions a month
Free or Smarter
FreeSmarter
Grow guides, pest pages, articlesRead allRead all
Ask Laisha5 a dayUp to 1,000 a month
Exam practiceThe sample on each pageEvery question, timed papers
Crop calendar and pest alerts—For your own fields
Calculators and tools—All
Uploads and reports—100 a month, real files
10 days free for every new account, no card.