LAISHA
Open Laisha

GATE Engineering Thermodynamics: practice questions

GATE — Agricultural Engineering (AG) · India · IITs and IISc on rotation (2027: IIT Madras)

Original practice questions written to the published syllabus · not past papers
10worked here, free
36written to this exam in this subject
7syllabus units

About GATE

GATE — Agricultural Engineering (AG) is a postgraduate admission exam run by IITs and IISc on rotation (2027: IIT Madras), for candidates in India. Computer-based, 3 hours, 100 marks (15 General Aptitude + 85 technical: 25 one-mark and 30 two-mark questions). MCQ, MSQ and NAT; negative marking on MCQ only (−1/3 for one-mark, −2/3 for two-mark); no partial credit on MSQ. On-screen virtual calculator.

Source: gate2027.iitm.ac.in.

Checked against the exam body's published information. Formats and fees change; confirm the current edition there before you book.

Engineering Thermodynamics in GATE

Thermodynamic principles of IC engines under Farm Power: Otto and Diesel efficiency, compression and cut-off ratio, MEP, and isentropic compression temperatures, usually as numerical-answer questions. Processing sections draw on psychrometry (humidity ratio, dryer air balances, evaporative cooling) and refrigeration (COP, TR, refrigerant flow). Answers must be computed to the stated precision, so carry kelvin and kJ consistently.

Energy, work, heat and the cycles behind engines, refrigerators and dryers.

Our 36 GATE questions in this subject: 9 easy, 18 medium, 9 hard, across 7 units.

10 practice questions, worked

Choose an answer, then open the working. Each explanation says why the right answer is right and why the others are not.

These 10 were written to GATE and are not shown on any other exam's page.

Question 1 · hard

Air at 300 K and 100 kPa is compressed reversibly and adiabatically in a diesel engine cylinder with a compression ratio of 16 (γ = 1.4). The temperature at the end of compression is about

  1. 4800 K
  2. 2174 K
  3. 662 K
  4. 909 K
Answer and working

D. 909 K

For an isentropic process T2/T1 = (V1/V2)^(γ−1) = 16^0.4, so T2 = 300 × 3.031 = 909 K. 4800 K multiplies by the volume ratio itself, 2174 K uses exponent 1/γ, and 662 K uses the pressure-ratio exponent (γ−1)/γ with a volume ratio.

Question 2 · hard

Air at 300 K is compressed adiabatically through a pressure ratio of 6 in a compressor with an isentropic efficiency of 85 % (γ = 1.4). The actual delivery temperature is about

  1. 470 K
  2. 501 K
  3. 536 K
  4. 723 K
Answer and working

C. 536 K

T2s = 300 × 6^(0.4/1.4) = 500.6 K. ηC = (T2s − T1)/(T2 − T1), so T2 = 300 + 200.6/0.85 = 536 K. 470 K multiplies the ideal rise by 0.85 (giving less than isentropic, impossible), 501 K is the isentropic temperature, and 723 K uses a volume-ratio exponent and divides the whole temperature by η.

Question 3 · easy

The air-standard efficiency of an Otto cycle with a compression ratio of 8 (γ = 1.4) is

  1. 87.5 %
  2. 43.5 %
  3. 56.5 %
  4. 64.6 %
Answer and working

C. 56.5 %

η = 1 − 8^(−0.4) = 1 − 0.4353 = 56.5 %. 87.5 % uses 1 − 1/r without the exponent, 43.5 % is the term 1/r^(γ−1) itself, and 64.6 % uses exponent 0.5 instead of γ − 1 = 0.4.

Question 4 · medium

A tractor diesel engine is modelled as an air-standard Diesel cycle with compression ratio 16 and cut-off ratio 2 (γ = 1.4). Its efficiency is about

  1. 67.0 %
  2. 61.4 %
  3. 45.9 %
  4. 34.0 %
Answer and working

B. 61.4 %

η = 1 − (1/r^(γ−1)) × (rc^γ − 1)/(γ(rc − 1)) = 1 − 0.3299 × 1.1707 = 61.4 %. 67.0 % is the Otto efficiency at r = 16 (no cut-off penalty), 45.9 % drops γ from the denominator, and 34.0 % replaces the bracket with rc.

Question 5 · easy

In the Diesel cycle the cut-off ratio is defined as

  1. the total cylinder volume divided by the clearance volume
  2. the peak pressure divided by the pressure at the end of compression
  3. the swept volume divided by the volume at the end of heat addition
  4. the volume at the end of heat addition divided by the volume at its start
Answer and working

D. the volume at the end of heat addition divided by the volume at its start

Cut-off ratio rc = V3/V2, the expansion during constant-pressure heat addition. Total volume over clearance volume is the compression ratio, the pressure ratio describes the constant-volume part of a dual cycle, and the last ratio has no standard name.

Question 6 · hard

At a fixed compression ratio, what happens to the air-standard Diesel-cycle efficiency as the load (and so the cut-off ratio) increases?

  1. It increases, because more heat is added at the peak pressure of the cycle
  2. It stays constant, because efficiency depends on compression ratio only
  3. It decreases, because heat is added over a longer part of the expansion stroke
  4. It first rises and then falls, peaking at a cut-off ratio of about two
Answer and working

C. It decreases, because heat is added over a longer part of the expansion stroke

The factor (rc^γ − 1)/(γ(rc − 1)) grows with rc, so efficiency falls as cut-off ratio rises; heat added later in the stroke is converted less effectively. Dependence on r alone holds only for the Otto cycle, and there is no maximum at rc = 2.

Question 7 · medium

In an ideal vapour-compression cycle, the enthalpies are 395 kJ/kg at evaporator exit, 425 kJ/kg at compressor exit and 250 kJ/kg at condenser exit. The COP is

  1. 5.83
  2. 0.207
  3. 8.33
  4. 4.83
Answer and working

D. 4.83

Refrigerating effect = 395 − 250 = 145 kJ/kg; compressor work = 425 − 395 = 30 kJ/kg; COP = 145/30 = 4.83. 5.83 is the heat-pump COP (condenser heat 175/30), 0.207 is the inverse, and 8.33 uses the condenser-exit enthalpy as the refrigerating effect.

Question 8 · medium

A cold store needs 10 TR of refrigeration (1 TR = 3.517 kW). The refrigerating effect of the cycle is 145 kJ/kg. The refrigerant mass flow rate is about

  1. 14.6 kg/s
  2. 0.069 kg/s
  3. 0.243 kg/s
  4. 1.17 kg/s
Answer and working

C. 0.243 kg/s

ṁ = Q̇/RE = 35.17/145 = 0.243 kg/s. 14.6 is the flow per minute labelled per second, 0.069 divides TR by kJ/kg without converting to kW, and 1.17 divides by a compressor work of 30 kJ/kg instead of the refrigerating effect.

Question 9 · easy

The dew-point temperature of moist air is

  1. the temperature shown by a thermometer with a wetted wick in a stream of moving air
  2. the temperature reached when the air is saturated adiabatically by water at that temperature
  3. the temperature at which the air becomes saturated when cooled at constant humidity ratio
  4. the temperature at which the relative humidity of the air falls to exactly fifty percent
Answer and working

C. the temperature at which the air becomes saturated when cooled at constant humidity ratio

Dew point is the saturation temperature at the actual vapour pressure: cool the air at constant W until condensation begins. The wetted-wick reading is the wet-bulb temperature, adiabatic saturation defines the adiabatic-saturation temperature, and 50 % RH has no special name.

Question 10 · medium

Why are psychrometric properties such as humidity ratio and enthalpy expressed per kilogram of dry air rather than per kilogram of moist air?

  1. Dry air has a far higher specific heat than water vapour in the usual range
  2. The mass of dry air stays constant through heating, cooling, humidifying and drying
  3. The mass of water vapour in air is too small to be measured with any accuracy
  4. Dalton's law applies only to dry air and cannot be used for the moist mixture
Answer and working

B. The mass of dry air stays constant through heating, cooling, humidifying and drying

In most air-handling processes water is added or removed but the dry-air flow is unchanged, so it is the natural basis. Water vapour's cp (about 1.88) is higher than dry air's, vapour mass is readily measured, and Dalton's law applies to the whole mixture.

A study plan for Engineering Thermodynamics in GATE

This plan follows where our questions actually fall, so the time goes where the marks are likely to be. It is our reading of the syllabus, not the exam body's weighting.

  1. First, the heavy units (72% of the 36 questions): Air-standard cycles: Otto, Diesel, dual and Brayton (10, 28%); Introduction to psychrometry (10, 28%); Vapour-compression cycle basics (6, 17%).

    Read the manual chapters for these first and do every worked question you can find on them.

  2. Then the middle band: Properties of steam, steam tables and the Mollier chart (3, 8%); Steady-flow energy equation (3, 8%); Ideal gas processes (2, 6%).

    Aim for one sitting per unit, then mixed questions across them.

  3. Then the lighter units: Second law, entropy and the Carnot cycle (2, 6%).

    Learn the definitions, classifications and standard numbers; these units are more often recalled than worked.

  4. Leave time for the hard ones: Properties of steam, steam tables and the Mollier chart (2 hard of 3), Ideal gas processes (1 hard of 2), Second law, entropy and the Carnot cycle (1 hard of 2).

    Come back to these after a first pass, untimed, and read every explanation, including for the options you rejected.

  5. Bank the easy marks: Vapour-compression cycle basics (2 easy of 6); Steady-flow energy equation (1 easy of 3).

    Do these early in revision so they are fast on the day.

  6. Finish timed. Sit the subject as a timed set without notes, mark it, and send each wrong answer back to its unit above.

Last updated · How Laisha writes and checks its pages · Report a mistake

Ask Laisha about this

Opens Laisha's chat with your question ready to send. Sign in or start free.

Unlock every question — GATE Engineering Thermodynamics

US$10 a month · one price worldwide · cancel any time

  • Every practice question in this subject, with full working
  • Timed exam papers and progress by unit
  • Ask Laisha to explain any answer — up to 1,000 questions a month
Free or Smarter
FreeSmarter
Grow guides, pest pages, articlesRead allRead all
Ask Laisha5 a dayUp to 1,000 a month
Exam practiceThe sample on each pageEvery question, timed papers
Crop calendar and pest alerts—For your own fields
Calculators and tools—All
Uploads and reports—100 a month, real files
10 days free for every new account, no card.