LAISHA
Open Laisha

Tamil Nadu PSC Fluid Mechanics & Open Channel Hydraulics: practice questions

Tamil Nadu PSC — Agricultural Engineering (Code 164, degree standard) · India · Tamil Nadu Public Service Commission

Original practice questions written to the published syllabus · not past papers
10worked here, free
44written to this exam in this subject
17syllabus units

About Tamil Nadu PSC

Tamil Nadu PSC — Agricultural Engineering (Code 164, degree standard) is a government recruitment exam run by Tamil Nadu Public Service Commission, for candidates in India. Degree-standard subject paper (for posts such as Assistant Engineer (Agri)).

Source: tnpsc.gov.in.

Checked against the exam body's published information. Formats and fees change; confirm the current edition there before you book.

Fluid Mechanics & Open Channel Hydraulics in Tamil Nadu PSC

Fluids at rest and in motion, pipe flow and open channels: the base of irrigation, drainage, pumping and conservation structures.

Our 44 Tamil Nadu PSC questions in this subject: 26 easy, 16 medium, 2 hard, across 17 units.

10 practice questions, worked

Choose an answer, then open the working. Each explanation says why the right answer is right and why the others are not.

These 10 were written to Tamil Nadu PSC and are not shown on any other exam's page.

Question 1 · easy

In the Hazen-Williams equation, what does a higher value of the coefficient C indicate?

  1. A larger pipe diameter
  2. A smoother pipe with lower friction loss
  3. A more viscous liquid
  4. A rougher pipe with higher friction loss
Answer and working

B. A smoother pipe with lower friction loss

C sits in the denominator of the head-loss form, h_f ∝ 1/C^1.852, so a larger C means less loss, i.e. a smoother pipe. Plastic pipe has high C (around 140–150); old tuberculated iron much lower. C does not represent diameter or fluid properties; the equation is for water only.

Question 2 · easy

Replacing a sharp-edged pipe entrance from a tank with a well-rounded bell-mouth entrance changes the entrance loss coefficient roughly:

  1. From about 0.05 to about 0.5
  2. It does not change; entrance losses depend only on velocity
  3. From about 1.0 to about 0.5
  4. From about 0.5 to about 0.05 or less
Answer and working

D. From about 0.5 to about 0.05 or less

A sharp (square-edged) entrance causes a vena contracta and re-expansion, K ≈ 0.5. Rounding the edge suppresses separation, reducing K to about 0.05 or less. A projecting (re-entrant) pipe is worse, around 0.8–1.0.

Question 3 · medium

A pipeline consists of 400 m of 200 mm pipe followed by 300 m of 150 mm pipe. Neglecting minor losses and taking the same friction factor throughout, what length of 200 mm pipe is hydraulically equivalent?

  1. 1111 m
  2. 700 m
  3. 933 m
  4. 1664 m
Answer and working

D. 1664 m

Dupuit: L/D⁵ = ΣLᵢ/Dᵢ⁵, so L = 400 + 300 × (0.2/0.15)⁵ = 400 + 300 × 4.21 = 1664 m. Simply adding lengths (700 m) ignores the much higher loss in the smaller pipe; using D² or D³ understates it. 933 m scales by D² and 1111 m by D³.

Question 4 · easy

For pipes connected in series, which quantity is the same in every pipe?

  1. The friction head loss
  2. The mean velocity
  3. The Reynolds number
  4. The discharge
Answer and working

D. The discharge

In series the same flow passes through each pipe in turn and the losses add. In parallel the head loss is the same in each branch and the flows add. Velocity and Re change with diameter.

Question 5 · medium

A broad-crested weir 3 m long carries water under a head of 0.5 m above the crest (neglect approach velocity, take C_d = 1). What is the maximum discharge?

  1. 1.95 m³/s
  2. 1.81 m³/s
  3. 0.904 m³/s
  4. 3.32 m³/s
Answer and working

B. 1.81 m³/s

Flow passes through critical depth on the crest, h = 2H/3, giving Q = 1.705 C_d L H^1.5 = 1.705 × 3 × 0.5^1.5 = 1.81 m³/s. The sharp-crested constant 1.84 gives 1.95 m³/s; taking the depth on the crest as H itself gives 3.32 m³/s. 0.904 m³/s uses H^2.5 instead of H^1.5.

Question 6 · easy

Using the Chezy equation with C = 50 m^0.5/s, what is the mean velocity in a channel with hydraulic radius 0.8 m and bed slope 0.0004?

  1. 0.894 m/s
  2. 0.0179 m/s
  3. 0.0160 m/s
  4. 0.862 m/s
Answer and working

A. 0.894 m/s

V = C√(RS) = 50 × √(0.8 × 0.0004) = 50 × 0.0179 = 0.894 m/s. Mixing in Manning's R^(2/3) gives 0.862 m/s. 0.0160 m/s multiplies C × R × S and forgets the square root.

Question 7 · hard

An earthen trapezoidal canal has bed width 4 m, side slopes 2 horizontal to 1 vertical, bed slope 0.0003 and Manning's n = 0.022. What discharge does it carry at a uniform depth of 1.5 m?

  1. 8.54 m³/s
  2. 14.8 m³/s
  3. 0.141 m³/s
  4. 8.16 m³/s
Answer and working

D. 8.16 m³/s

A = (b + zy)y = (4 + 3) × 1.5 = 10.5 m²; P = b + 2y√(1 + z²) = 4 + 3√5 = 10.7 m; R = 0.981 m. Q = (A/n)R^(2/3)S^(1/2) = (10.5/0.022) × 0.987 × 0.0173 = 8.16 m³/s. Taking the sloping side length as zy instead of y√(1 + z²) gives 8.54 m³/s; using the top width in the area gives 14.8 m³/s. 0.141 m³/s uses S instead of √S.

Question 8 · medium

A wide rectangular channel carries a discharge of 3 m³/s per metre of width. What is the critical depth, and the minimum specific energy?

  1. y_c = 0.972 m; E_min = 1.46 m
  2. y_c = 0.958 m; E_min = 1.44 m
  3. y_c = 0.972 m; E_min = 0.972 m
  4. y_c = 0.674 m; E_min = 1.01 m
Answer and working

A. y_c = 0.972 m; E_min = 1.46 m

y_c = (q²/g)^(1/3) = (9/9.81)^(1/3) = 0.972 m. At critical depth the velocity head is y_c/2, so E_min = 1.5 y_c = 1.46 m. Forgetting to square q gives 0.674 m; a square root instead of cube root gives 0.958 m.

Question 9 · easy

Water flows at 3 m/s with a depth of 0.5 m in a rectangular channel. What is the Froude number and the flow regime?

  1. 0.612; subcritical
  2. 1.35; subcritical
  3. 1.35; supercritical
  4. 0.958; subcritical
Answer and working

C. 1.35; supercritical

Fr = V/√(gy) = 3/√(9.81 × 0.5) = 1.35. Fr > 1 means supercritical (rapid) flow; surface waves cannot travel upstream. Using √(2gy), the jet-velocity form, gives 0.958 and the wrong regime.

Question 10 · medium

A hydraulic jump forms in a horizontal rectangular channel. The depth before the jump is 0.4 m and the upstream Froude number is 5. What is the sequent depth after the jump?

  1. 2.64 m
  2. 3.04 m
  3. 2.00 m
  4. 1.08 m
Answer and working

A. 2.64 m

y₂/y₁ = ½[√(1 + 8Fr₁²) − 1] = ½[√201 − 1] = 6.59. y₂ = 0.4 × 6.59 = 2.64 m. Forgetting to square Fr₁ gives 1.08 m. 3.04 m uses + 1 instead of − 1 in the bracket; 2.00 m multiplies y₁ by Fr₁.

A study plan for Fluid Mechanics & Open Channel Hydraulics in Tamil Nadu PSC

This plan follows where our questions actually fall, so the time goes where the marks are likely to be. It is our reading of the syllabus, not the exam body's weighting.

  1. First, the heavy units (52% of the 44 questions): Weirs and notches (7, 16%); Bernoulli's equation: venturimeter, orifice meter and pitot tube (4, 9%); Dimensional analysis and similitude (3, 7%); Forces on submerged surfaces and buoyancy (3, 7%); Minor losses (3, 7%); Orifices, mouthpieces and tank emptying (3, 7%).

    Read the manual chapters for these first and do every worked question you can find on them.

  2. Then the middle band: Specific energy and critical depth (3, 7%); Uniform flow in open channels: Manning and Chezy (3, 7%); Darcy-Weisbach equation and Moody diagram (2, 5%); Hydrostatics and manometry (2, 5%); Laminar and turbulent flow in pipes (2, 5%); Most economical channel section (2, 5%).

    Aim for one sitting per unit, then mixed questions across them.

  3. Then the lighter units: Pipes in series and parallel (2, 5%); Properties of fluids (2, 5%); Continuity equation (1, 2%); Hazen-Williams equation (1, 2%); Hydraulic jump (1, 2%).

    Learn the definitions, classifications and standard numbers; these units are more often recalled than worked.

  4. Leave time for the hard ones: Uniform flow in open channels: Manning and Chezy (1 hard of 3), Weirs and notches (1 hard of 7).

    Come back to these after a first pass, untimed, and read every explanation, including for the options you rejected.

  5. Bank the easy marks: Hydrostatics and manometry (2 easy of 2); Laminar and turbulent flow in pipes (2 easy of 2).

    Do these early in revision so they are fast on the day.

  6. Finish timed. Sit the subject as a timed set without notes, mark it, and send each wrong answer back to its unit above.

Last updated · How Laisha writes and checks its pages · Report a mistake

Ask Laisha about this

Opens Laisha's chat with your question ready to send. Sign in or start free.

Unlock every question — Tamil Nadu PSC Fluid Mechanics & Open Channel Hydraulics

US$10 a month · one price worldwide · cancel any time

  • Every practice question in this subject, with full working
  • Timed exam papers and progress by unit
  • Ask Laisha to explain any answer — up to 1,000 questions a month
Free or Smarter
FreeSmarter
Grow guides, pest pages, articlesRead allRead all
Ask Laisha5 a dayUp to 1,000 a month
Exam practiceThe sample on each pageEvery question, timed papers
Crop calendar and pest alerts—For your own fields
Calculators and tools—All
Uploads and reports—100 a month, real files
10 days free for every new account, no card.