Tamil Nadu PSC — Agricultural Engineering (Code 164, degree standard) · India · Tamil Nadu Public Service Commission
Original practice questions written to the published syllabus · not past papersTamil Nadu PSC — Agricultural Engineering (Code 164, degree standard) is a government recruitment exam run by Tamil Nadu Public Service Commission, for candidates in India. Degree-standard subject paper (for posts such as Assistant Engineer (Agri)).
Source: tnpsc.gov.in.
Checked against the exam body's published information. Formats and fees change; confirm the current edition there before you book.
Designing and evaluating sprinkler and drip systems, from emitter hydraulics to pump selection.
Our 45 Tamil Nadu PSC questions in this subject: 31 easy, 12 medium, 2 hard, across 14 units.
Choose an answer, then open the working. Each explanation says why the right answer is right and why the others are not.
These 10 were written to Tamil Nadu PSC and are not shown on any other exam's page.
A sprinkler catch pattern shows almost no water near the sprinkler and a heavy ring near the edge of the wetted circle, with large drops. What is the most likely cause?
D. Operating pressure too low for the nozzle
Low pressure does not break up the jet, so large drops travel to the outer part of the circle, giving the 'doughnut' pattern. Excess pressure does the opposite: fine drops, mist, drift and extra water near the sprinkler.
A net depth of 60 mm is to be applied by a portable lateral with application efficiency 75 % at an application rate of 8 mm/h. What is the set time?
A. 10.0 h
Gross depth = 60 / 0.75 = 80 mm; set time = 80 / 8 = 10.0 h. Dividing the net depth by the rate gives 7.5 h and multiplying by efficiency gives 5.62 h, both of which under-irrigate; 13.3 h divides by efficiency twice.
How is sprinkler spacing normally adjusted as the design wind speed at a site increases?
D. Spacing is reduced as a fraction of wetted diameter, especially across the wind
Wind distorts and shortens the wetted pattern upwind and across the wind, so overlap must increase: spacing is set at a smaller fraction of the wetted diameter, often closest across the wind. Lowering pressure produces larger drops but does not restore overlap.
Christiansen's uniformity coefficient is based on which statistic of catch-can depths?
A. The mean absolute deviation from the mean
CU = 100 [1 − Σ|xi − x̄| / (n x̄)] uses absolute deviations. The standard deviation is used by the Wilcox–Swailes coefficient and by statistical uniformity; the lowest quarter is used by distribution uniformity.
A PVC mainline of 125 mm internal diameter carries 20 L/s. What is the flow velocity, and is it within a common 1.5 m/s working limit for plastic mains?
B. 1.63 m/s; slightly above the limit
V = Q/A = 0.020 / (π/4 × 0.125²) = 0.020 / 0.01227 = 1.63 m/s, just over 1.5 m/s, so the next larger size should be checked on annual cost and surge. Using πD² instead of πD²/4 for area gives 0.41 m/s.
Drip laterals are most commonly made of which material?
B. Polyethylene
Laterals are flexible polyethylene tubing (commonly LLDPE/LDPE blends) because it is cheap, flexible, resistant to fertilisers and allows emitters to be inserted or moulded in. Aluminium is used for portable sprinkler laterals; PVC is common for buried mains.
A crop needs 60 kg N/ha in 12 equal fertigations on 2.5 ha, supplied as urea (46 % N). How much urea is needed per fertigation?
D. 27.2 kg
N per fertigation = 60/12 × 2.5 = 12.5 kg; urea = 12.5/0.46 = 27.2 kg. 12.5 kg is N, not urea; 326 kg is the season's total; 10.9 kg is per hectare only.
What does the economic pipe size minimise?
D. The sum of annualised pipe cost and annual pumping energy cost
Larger pipes cost more but save energy by reducing friction. The economic size is the one with the least total annual cost; minimising pipe cost alone leads to high energy bills, and minimising friction alone leads to oversized pipes.
A micro-irrigation system costs 150 000 and yields a net annual benefit of 50 000. What is the simple payback period?
C. 3 years
Simple payback = capital / annual net benefit = 150 000 / 50 000 = 3 years. 0.33 is the inverse ratio. Simple payback ignores the time value of money, which NPV and IRR include. 2 years deducts one year's benefit from the capital first ((150 000 − 50 000)/50 000); 4 years adds it instead ((150 000 + 50 000)/50 000).
A farmer asks the government engineer what share of drip system cost a national subsidy scheme will pay. What is the correct professional response?
C. Check the current guidelines: rates, ceilings and conditions change and vary by farmer category and region
Subsidy schemes (often with higher rates for small and marginal farmers) set rates, area ceilings and component-certification conditions that change over time and between states or countries; the engineer should quote the current guideline.
This plan follows where our questions actually fall, so the time goes where the marks are likely to be. It is our reading of the syllabus, not the exam body's weighting.
Read the manual chapters for these first and do every worked question you can find on them.
Aim for one sitting per unit, then mixed questions across them.
Learn the definitions, classifications and standard numbers; these units are more often recalled than worked.
Come back to these after a first pass, untimed, and read every explanation, including for the options you rejected.
Do these early in revision so they are fast on the day.
Last updated · How Laisha writes and checks its pages · Report a mistake
US$10 a month · one price worldwide · cancel any time
| Free | Smarter | |
|---|---|---|
| Grow guides, pest pages, articles | Read all | Read all |
| Ask Laisha | 5 a day | Up to 1,000 a month |
| Exam practice | The sample on each page | Every question, timed papers |
| Crop calendar and pest alerts | — | For your own fields |
| Calculators and tools | — | All |
| Uploads and reports | — | 100 a month, real files |
An AI operating system for agriculture: free guides, manuals and tools written for every country.