India · Tamil Nadu Public Service Commission
Tamil Nadu PSC — Agricultural Engineering (Code 164, degree standard) is a government recruitment exam run by Tamil Nadu Public Service Commission, for candidates in India.
Degree-standard subject paper (for posts such as Assistant Engineer (Agri)).
Units I–V were read; later units on farm power, machinery and processing were not fully captured.
Our reading of the syllabus, from the questions we have written to this exam; the exam body's own weighting, where published, is under Format above.
Start here: read these subjects' manuals first and work their questions until the reasoning is automatic.
One pass per subject, then mixed sets across them.
Definitions, classifications and standard figures; quick to revise, easy marks to lose.
Leave untimed time for these and read every explanation, including for the options you rejected.
Official source: tnpsc.gov.in
Original questions written to this exam's published syllabus and pattern. Not past papers.
1. A distributary has a culturable command area of 20,000 ha. The intensity of irrigation in the peak season is 60 % and the duty at its head is 1,500 ha/cumec. What discharge must it carry?
B. 8.0 m³/s
Irrigated area = 0.60 × 20,000 = 12,000 ha; Q = 12,000 / 1,500 = 8.0 m³/s. 13.3 ignores intensity; 0.8 is a decimal slip; 4.8 applies intensity twice.
Irrigation Engineering (Soil-Water-Plant, Conveyance, Surface Methods) · Command area development
2. Why do most watershed programmes require beneficiaries to contribute part of the cost of works on private land?
C. It tests genuine demand and builds a fund and a sense of ownership for maintenance after the project
Contribution in cash or labour signals that farmers want the work, and the collected money commonly goes into a watershed development fund for later maintenance. Programmes set lower rates for small and marginal and disadvantaged farmers precisely so the poor are not excluded.
Watershed Planning & Management · Participatory watershed planning
3. On a 20% slope the soil is deep enough to allow at most 0.5 m of cut at the inner edge of a level bench (vertical risers, balanced cut and fill). The widest bench that can be built without cutting below this depth is:
A. 5.0 m
For a balanced level bench, the cut at the inner edge is VI/2. Cut ≤ 0.5 m gives VI ≤ 1.0 m. W = 100 VI/S = 100 × 1.0/20 = 5.0 m. Treating 0.5 m as the VI gives 2.5 m, an unnecessarily narrow bench. 0.2 m multiplies VI by S/100 instead of dividing.
Soil & Water Conservation Engineering · Bench and broad-base terraces
4. On a land capability map, a mapping unit labelled 'IIIe' means:
A. cultivable land with severe limitations, erosion hazard being the dominant one
Class III is arable but has severe limitations that reduce the choice of crops or need special conservation practices; the subclass e shows that erosion hazard is the dominant limitation. Moderate limitations define class II, and w would denote wetness.
Watershed Planning & Management · Land capability classification
5. What does the economic pipe size minimise?
D. The sum of annualised pipe cost and annual pumping energy cost
Larger pipes cost more but save energy by reducing friction. The economic size is the one with the least total annual cost; minimising pipe cost alone leads to high energy bills, and minimising friction alone leads to oversized pipes.
Sprinkler & Micro-Irrigation Systems · Economics of pressurised irrigation
6. What is the measurement book used for in public works?
C. Recording measurements of work done and materials received, as the basis for payments
The measurement book is the original record of quantities measured by the engineer; running and final bills are prepared from it, and auditors check against it. Payroll, specifications and test registers are separate records.
Building Materials, Theory of Structures & Construction · Specifications and contracts
7. A graded border is best described as:
C. A long strip bounded by dikes, sloping along its length with no cross slope
Borders are strips with a longitudinal slope and zero cross slope so the sheet of water spreads evenly across. The level enclosed area is a basin, row channels are furrows, and the pipe describes drip.
Irrigation Engineering (Soil-Water-Plant, Conveyance, Surface Methods) · Border irrigation
8. A channel with bed width 4 m and side slopes 1.5:1 (H:V) has centre depths of 1.0, 1.6 and 2.2 m at chainages 30 m apart, ground level across. What is the volume of cut by the trapezoidal (average end area) formula?
D. 630.6 m³
Areas: 5.50, 10.24, 16.06 m². V = d[(A1 + A3)/2 + A2] = 30[(5.50 + 16.06)/2 + 10.24] = 630.6 m³. The prismoidal value is 625.2 m³; ignoring the middle section gives 646.8 m³. 954.0 m³ adds all three areas without halving the end sections.
Surveying & Levelling · Earthwork volume computation
Last updated · How Laisha writes and checks its pages · Report a mistake
US$10 a month · one price worldwide · cancel any time
| Free | Smarter | |
|---|---|---|
| Grow guides, pest pages, articles | Read all | Read all |
| Ask Laisha | 5 a day | Up to 1,000 a month |
| Exam practice | The sample on each page | Every question, timed papers |
| Crop calendar and pest alerts | — | For your own fields |
| Calculators and tools | — | All |
| Uploads and reports | — | 100 a month, real files |
An AI operating system for agriculture: free guides, manuals and tools written for every country.