LAISHA
Open Laisha

Tamil Nadu PSC Irrigation Engineering (Soil-Water-Plant, Conveyance, Surface Methods): practice questions

Tamil Nadu PSC — Agricultural Engineering (Code 164, degree standard) · India · Tamil Nadu Public Service Commission

Original practice questions written to the published syllabus · not past papers
10worked here, free
50written to this exam in this subject
14syllabus units

About Tamil Nadu PSC

Tamil Nadu PSC — Agricultural Engineering (Code 164, degree standard) is a government recruitment exam run by Tamil Nadu Public Service Commission, for candidates in India. Degree-standard subject paper (for posts such as Assistant Engineer (Agri)).

Source: tnpsc.gov.in.

Checked against the exam body's published information. Formats and fees change; confirm the current edition there before you book.

Irrigation Engineering (Soil-Water-Plant, Conveyance, Surface Methods) in Tamil Nadu PSC

How much water a crop needs, when to give it, how to measure and convey it, and how to design surface irrigation.

Our 50 Tamil Nadu PSC questions in this subject: 28 easy, 21 medium, 1 hard, across 14 units.

10 practice questions, worked

Choose an answer, then open the working. Each explanation says why the right answer is right and why the others are not.

These 10 were written to Tamil Nadu PSC and are not shown on any other exam's page.

Question 1 · easy

Which set describes the FAO-56 hypothetical reference crop?

  1. Grass 0.12 m tall, surface resistance 0 s/m, albedo 0.05
  2. Grass 0.12 m tall, resistance 70 s/m, albedo 0.23
  3. Alfalfa 0.5 m tall, surface resistance 45 s/m, albedo 0.23
  4. Open water surface, no surface resistance, albedo 0.08
Answer and working

B. Grass 0.12 m tall, resistance 70 s/m, albedo 0.23

FAO-56 defines the reference as hypothetical grass, 0.12 m tall, rs = 70 s/m, albedo 0.23. The alfalfa option describes a tall reference (ASCE), and the others describe open water or an unrealistic surface.

Question 2 · medium

Before irrigation a soil holds 18 % water by mass; field capacity is 28 % by mass, bulk density 1.4 g/cm³ and root depth 60 cm. If application efficiency is 70 %, what gross depth should be applied?

  1. 85.7 mm
  2. 58.8 mm
  3. 84 mm
  4. 120 mm
Answer and working

D. 120 mm

Net depth = (0.28 − 0.18) × 1.4 × 600 mm = 84 mm; gross = 84/0.70 = 120 mm. 84 mm is the net depth; 85.7 mm forgets bulk density; 58.8 mm multiplies by efficiency.

Question 3 · easy

The mean diameter of bed sediment is 0.36 mm. What is Lacey's silt factor?

  1. 0.63
  2. 1.06
  3. 0.80
  4. 2.93
Answer and working

B. 1.06

f = 1.76 √d = 1.76 × √0.36 = 1.76 × 0.6 = 1.06 (d in mm). 0.63 forgets the square root; 2.93 divides; 0.80 takes the root of the product.

Question 4 · medium

Apart from reducing seepage, which is a direct hydraulic benefit of lining a canal?

  1. Higher roughness slows water and reduces erosion
  2. Lining increases the time of travel so more water infiltrates along the way
  3. A smaller section carries the same flow
  4. Lining raises the water table in the command
Answer and working

C. A smaller section carries the same flow

A smooth lining lowers n and permits higher velocities, so a smaller section carries the same flow. Lining reduces, not raises, waterlogging, and increased infiltration is the opposite of its purpose.

Question 5 · easy

A graded border is best described as:

  1. Small channels between crop rows
  2. A closed pipe with outlets at each plant
  3. A long strip bounded by dikes, sloping along its length with no cross slope
  4. A level area enclosed by dikes on all sides and filled rapidly to a set depth
Answer and working

C. A long strip bounded by dikes, sloping along its length with no cross slope

Borders are strips with a longitudinal slope and zero cross slope so the sheet of water spreads evenly across. The level enclosed area is a basin, row channels are furrows, and the pipe describes drip.

Question 6 · medium

With the same available stream size, how should basin size change from a clay to a sandy loam?

  1. Basins should be larger on the sandy loam
  2. Basins should be the same area but deeper on the sandy loam
  3. Smaller on the sandy loam
  4. Basin size does not depend on soil
Answer and working

C. Smaller on the sandy loam

On high-intake soil water infiltrates quickly, so a small basin is needed to cover it before too much soaks in near the inlet. Fine soils allow larger basins for the same stream.

Question 7 · easy

A canal diverts 1.0 m³/s at the head; 0.70 m³/s reaches the fields, and 0.49 m³/s is stored in the root zone. What is the field application efficiency?

  1. 49 %
  2. 143 %
  3. 30 %
  4. 70 %
Answer and working

D. 70 %

Application efficiency = water stored in root zone / water delivered to the field = 0.49/0.70 = 70 %. 49 % is the overall (conveyance × application) efficiency; 143 % inverts the ratio; 30 % is the conveyance loss fraction.

Question 8 · easy

Which two losses reduce field application efficiency in surface irrigation?

  1. Canal seepage and evaporation from reservoirs (conveyance losses)
  2. Surface runoff (tailwater) and deep percolation below the root zone
  3. Transpiration and photosynthesis
  4. Interception by weeds in the main canal
Answer and working

B. Surface runoff (tailwater) and deep percolation below the root zone

Application efficiency is measured from the field inlet to the root zone, so its losses are runoff and deep percolation. Canal seepage lowers conveyance efficiency; transpiration is the beneficial use.

Question 9 · medium

A distributary has a culturable command area of 20,000 ha. The intensity of irrigation in the peak season is 60 % and the duty at its head is 1,500 ha/cumec. What discharge must it carry?

  1. 4.8 m³/s
  2. 8.0 m³/s
  3. 13.3 m³/s
  4. 0.8 m³/s
Answer and working

B. 8.0 m³/s

Irrigated area = 0.60 × 20,000 = 12,000 ha; Q = 12,000 / 1,500 = 8.0 m³/s. 13.3 ignores intensity; 0.8 is a decimal slip; 4.8 applies intensity twice.

Question 10 · easy

Warabandi, practised in the Indus basin of north-west India and Pakistan, is:

  1. Continuous flow to every farm in proportion to the crop ET, adjusted each week from pan evaporation readings
  2. A fixed weekly rotation giving each farmer the full outlet flow for a time proportional to landholding
  3. Auction of canal water to the highest bidder each season
  4. Delivery of water on demand by telephone request
Answer and working

B. A fixed weekly rotation giving each farmer the full outlet flow for a time proportional to landholding

Under warabandi, each farmer on an outlet gets a fixed day and time slot each week, its length proportional to area. It is equitable and simple but not responsive to crop need. The other options describe demand, continuous or market delivery.

A study plan for Irrigation Engineering (Soil-Water-Plant, Conveyance, Surface Methods) in Tamil Nadu PSC

This plan follows where our questions actually fall, so the time goes where the marks are likely to be. It is our reading of the syllabus, not the exam body's weighting.

  1. First, the heavy units (58% of the 50 questions): Command area development (8, 16%); Design of irrigation channels (6, 12%); Canal lining (5, 10%); Irrigation scheduling (5, 10%); Water measurement: weirs, Parshall flume and orifices (5, 10%).

    Read the manual chapters for these first and do every worked question you can find on them.

  2. Then the middle band: Basin irrigation (3, 6%); Border irrigation (3, 6%); Evapotranspiration and FAO-56 Penman-Monteith (3, 6%); Irrigation efficiencies and distribution uniformity (3, 6%); Soil-water-plant relations: field capacity, wilting point and MAD (3, 6%).

    Aim for one sitting per unit, then mixed questions across them.

  3. Then the lighter units: Effective rainfall (2, 4%); Furrow irrigation (2, 4%); Crop coefficients and crop water requirement (1, 2%); Underground pipeline systems (1, 2%).

    Learn the definitions, classifications and standard numbers; these units are more often recalled than worked.

  4. Leave time for the hard ones: Irrigation scheduling (1 hard of 5).

    Come back to these after a first pass, untimed, and read every explanation, including for the options you rejected.

  5. Bank the easy marks: Irrigation efficiencies and distribution uniformity (3 easy of 3); Soil-water-plant relations: field capacity, wilting point and MAD (3 easy of 3).

    Do these early in revision so they are fast on the day.

  6. Finish timed. Sit the subject as a timed set without notes, mark it, and send each wrong answer back to its unit above.

Last updated · How Laisha writes and checks its pages · Report a mistake

Ask Laisha about this

Opens Laisha's chat with your question ready to send. Sign in or start free.

Unlock every question — Tamil Nadu PSC Irrigation Engineering (Soil-Water-Plant, Conveyance, Surface Methods)

US$10 a month · one price worldwide · cancel any time

  • Every practice question in this subject, with full working
  • Timed exam papers and progress by unit
  • Ask Laisha to explain any answer — up to 1,000 questions a month
Free or Smarter
FreeSmarter
Grow guides, pest pages, articlesRead allRead all
Ask Laisha5 a dayUp to 1,000 a month
Exam practiceThe sample on each pageEvery question, timed papers
Crop calendar and pest alerts—For your own fields
Calculators and tools—All
Uploads and reports—100 a month, real files
10 days free for every new account, no card.