Rajasthan PSC — Assistant Agriculture Engineer (Agriculture Engineering syllabus) · India · Rajasthan Public Service Commission
Original practice questions written to the published syllabus · not past papersRajasthan PSC — Assistant Agriculture Engineer (Agriculture Engineering syllabus) is a government recruitment exam run by Rajasthan Public Service Commission, for candidates in India. Objective paper; the paper structure was not captured.
Source: rpsc.rajasthan.gov.in.
Checked against the exam body's published information. Formats and fees change; confirm the current edition there before you book.
Designing and evaluating sprinkler and drip systems, from emitter hydraulics to pump selection.
Our 35 Rajasthan PSC questions in this subject: 28 easy, 7 medium, 0 hard, across 14 units.
Choose an answer, then open the working. Each explanation says why the right answer is right and why the others are not.
These 10 were written to Rajasthan PSC and are not shown on any other exam's page.
In which sprinkler is the head stepped round by a spring-loaded arm that the jet knocks aside and that then strikes the sprinkler body?
D. Impact sprinkler
The impact sprinkler is driven by the jet deflecting a spring-loaded arm; the returning arm strikes the body and advances it. A gear-driven rotor uses a small water turbine and gears, a spray head has no rotating jet, and a bubbler is a micro-irrigation device for tree basins.
Which sprinkler system layout needs the least labour during the season but has the highest pipe cost per hectare?
A. Solid-set system
Solid-set and permanent systems have a lateral at every position, so nothing is moved during the season; the cost is the large quantity of pipe. Hand-move and semi-portable systems reuse a few laterals and trade pipe cost for labour. Permanent systems behave the same way.
Sprinklers discharging 0.5 L/s each are spaced 12 m along the lateral and 18 m between laterals. What is the average application rate?
D. 8.33 mm/h
I = 3600 q / (Sl × Sm) = 3600 × 0.5 / (12 × 18) = 8.33 mm/h (1 L over 1 m² is 1 mm). Using 1000 instead of 3600 (treating L/s as m³/h) gives 2.31; adding the spacings instead of multiplying gives 60; using 12 m × 12 m gives 12.5.
A level sprinkler lateral has design average pressure head 30 m, friction loss 6 m and riser height 1 m. What pressure head is needed at the lateral inlet?
A. 35.5 m
Hinlet = Ha + ¾ hf + Hr = 30 + 4.5 + 1 = 35.5 m. Adding the full friction loss gives 37 m (the average pressure occurs where about three-quarters of the loss has been used, not at the end); omitting the riser gives 34.5 m. 34.0 m uses half the friction loss instead of three-quarters (30 + 3 + 1).
What is the F factor for a pipe that delivers its entire flow through a single outlet at the far end?
D. 1.0
With one outlet at the end, the full flow travels the full length, so the loss equals the ordinary pipe loss and F = 1 (Christiansen's formula gives 0.351 + 0.5 + 0.154 ≈ 1.0 for N = 1). 0.35 is the many-outlet limit, not the single-outlet case; 0 would mean no friction loss at all.
What is the main function of an anti-drain (non-leakage) emitter?
A. Stops laterals draining
Anti-drain emitters close below a set pressure, keeping laterals full between short pulses and preventing low emitters from over-watering as the line drains. Constant discharge is the function of pressure compensation, a different feature.
An emitter exponent x = 1.0 indicates which flow regime?
A. Fully laminar flow
Laminar flow through a long, fine passage makes discharge proportional to head (x = 1). Fully turbulent orifice flow gives x = 0.5, vortex emitters about 0.4, and pressure-compensating emitters approach zero.
What minimum flushing velocity at the end of drip laterals does ASABE EP405 recommend?
D. About 0.3 m/s
EP405 recommends flushing at not less than about 0.3 m/s (about 1 ft/s) to carry sediment out. 1.5 m/s is a common velocity limit for mains, not a flushing criterion. About 0.03 m/s and about 3 m/s are factor-of-ten slips.
For a drip lateral with a very large number of emitters and friction computed by the Blasius form (m = 1.75), Christiansen's F approaches about:
A. 0.36
F → 1/(m + 1) = 1/2.75 = 0.364. 0.33 is the Darcy (m = 2) limit; 1.0 is for a single outlet at the end. 0.50 is the limit for m = 1, not 1.75.
Why are solenoid valves on irrigation zones usually normally closed?
D. So that the valve shuts and irrigation stops if power or the control signal fails
Normally closed valves fail safe: loss of power closes them, preventing uncontrolled irrigation and flooding.
This plan follows where our questions actually fall, so the time goes where the marks are likely to be. It is our reading of the syllabus, not the exam body's weighting.
Read the manual chapters for these first and do every worked question you can find on them.
Aim for one sitting per unit, then mixed questions across them.
Learn the definitions, classifications and standard numbers; these units are more often recalled than worked.
Do these early in revision so they are fast on the day.
Last updated · How Laisha writes and checks its pages · Report a mistake
US$10 a month · one price worldwide · cancel any time
| Free | Smarter | |
|---|---|---|
| Grow guides, pest pages, articles | Read all | Read all |
| Ask Laisha | 5 a day | Up to 1,000 a month |
| Exam practice | The sample on each page | Every question, timed papers |
| Crop calendar and pest alerts | — | For your own fields |
| Calculators and tools | — | All |
| Uploads and reports | — | 100 a month, real files |
An AI operating system for agriculture: free guides, manuals and tools written for every country.