LAISHA
Open Laisha

Rajasthan PSC Farm Machinery Management & Economics: practice questions

Rajasthan PSC — Assistant Agriculture Engineer (Agriculture Engineering syllabus) · India · Rajasthan Public Service Commission

Original practice questions written to the published syllabus · not past papers
10worked here, free
42written to this exam in this subject
11syllabus units

About Rajasthan PSC

Rajasthan PSC — Assistant Agriculture Engineer (Agriculture Engineering syllabus) is a government recruitment exam run by Rajasthan Public Service Commission, for candidates in India. Objective paper; the paper structure was not captured.

Source: rpsc.rajasthan.gov.in.

Checked against the exam body's published information. Formats and fees change; confirm the current edition there before you book.

Farm Machinery Management & Economics in Rajasthan PSC

Choosing, sizing, costing and replacing machines, and running a custom hiring centre that pays.

Our 42 Rajasthan PSC questions in this subject: 25 easy, 14 medium, 3 hard, across 11 units.

10 practice questions, worked

Choose an answer, then open the working. Each explanation says why the right answer is right and why the others are not.

These 10 were written to Rajasthan PSC and are not shown on any other exam's page.

Question 1 · easy

Why is the effective working width of a disc harrow in the field usually less than its rated width?

  1. Operators overlap adjacent passes to avoid leaving strips unworked
  2. Draft rises with speed so the harrow must be angled less
  3. Field efficiency is always applied to width rather than to operating time in the field
  4. The discs wear and become narrower during the season
Answer and working

A. Operators overlap adjacent passes to avoid leaving strips unworked

In practice each pass overlaps the previous one so no strip is missed; this unused width is one of the losses that field efficiency accounts for. Disc wear reduces diameter, not gang width, and draft does not change the working width.

Question 2 · easy

Timeliness cost of a field operation refers to:

  1. The wages paid for overtime during peak season
  2. The interest paid on a machine bought on credit just before the peak season
  3. Yield or quality lost by not doing the operation at its optimum time
  4. The extra fuel used when working at higher speed
Answer and working

C. Yield or quality lost by not doing the operation at its optimum time

Timeliness cost measures the crop value lost by operating early or late. Interest is a fixed cost, and fuel and wages are variable costs.

Question 3 · easy

A power tiller costs 650,000, has a life of 10 years and a salvage value of 10 % of cost. What is its annual straight-line depreciation?

  1. 71,500
  2. 58,500
  3. 52,000
  4. 65,000
Answer and working

B. 58,500

Depreciation = (P − S)/L = (650,000 − 65,000)/10 = 58,500. Ignoring salvage gives 65,000; 71,500 adds salvage instead of subtracting it. 52,000 subtracts the salvage twice ((650,000 − 130,000)/10).

Question 4 · easy

A tractor uses 6 L/h of diesel priced at 92 per litre. Lubrication is taken as 15 % of fuel cost. What is the fuel-plus-lubrication cost per hour?

  1. 82.8/h
  2. 634.8/h
  3. 6348/h
  4. 552.0/h
Answer and working

B. 634.8/h

Fuel = 6 × 92 = 552; lubrication = 0.15 × 552 = 82.8; total = 634.8 per hour. 552 omits lubrication; 82.8 is the lubrication alone. 6348/h is a factor-of-ten slip.

Question 5 · easy

Which depreciation method charges the same amount every year of the machine's life?

  1. Straight line
  2. Sinking fund
  3. Sum-of-years digits
  4. Double-declining balance
Answer and working

A. Straight line

Straight line spreads (P − S) equally over L years. Declining balance and sum-of-years digits charge more in early years; sinking fund charges more in later years.

Question 6 · medium

A custom hiring centre's tractor-implement set has annual fixed cost 240,000, planned use 800 h, and variable cost 900 per hour including operator. With a 15 % margin on full cost, what hire price per hour should it charge?

  1. 1,380/h
  2. 1,335/h
  3. 1,200/h
  4. 345/h
Answer and working

A. 1,380/h

Full cost = 240,000/800 + 900 = 1,200 per hour; price = 1,200 × 1.15 = 1,380. 1,200 has no margin; 1,335 applies the margin to variable cost only. 345/h applies the margin to the fixed part alone (300 × 1.15).

Question 7 · hard

A CHC buys a machine priced at 1,000,000 with a 40 % capital subsidy. Salvage is 100,000 after 8 years and interest is 10 %. By how much does the subsidy reduce the centre's annual depreciation plus interest on average investment?

  1. 90,000
  2. 40,000
  3. 70,000
  4. 50,000
Answer and working

C. 70,000

Without subsidy: (1,000,000 − 100,000)/8 + (1,000,000 + 100,000)/2 × 0.10 = 167,500. With subsidy (owner's cost 600,000): (600,000 − 100,000)/8 + (600,000 + 100,000)/2 × 0.10 = 97,500. Saving = 70,000. Only the depreciation part gives 50,000; only the interest on the whole subsidy gives 40,000. 90,000 charges interest on the whole 400,000 subsidy instead of its average (50,000 + 40,000).

Question 8 · medium

After a 40 % capital subsidy, a CHC's net investment is 2,000,000 and its expected net cash inflow is 450,000 per year. What is the simple payback period?

  1. 7.41 years
  2. 4.44 years
  3. 0.225 years
  4. 2.22 years
Answer and working

B. 4.44 years

Payback = investment / annual net inflow = 2,000,000 / 450,000 = 4.44 years. Inverting gives 0.225, the simple return rate, not the payback; 7.41 years uses the gross cost before the 40 % subsidy, which the owner did not pay. 2.22 years uses half the investment, as for an average-investment return (1,000,000/450,000).

Question 9 · easy

The most common reason custom hiring centres fail financially is:

  1. Too many trained operators competing to work the same few machines
  2. Excessive tax on hire income
  3. Low annual use, as machines sit idle outside the peak season
  4. Machines wearing out too slowly
Answer and working

C. Low annual use, as machines sit idle outside the peak season

Fixed cost per hour depends on hours rented. A fleet built around one short season carries its fixed cost over too few hours; fleet choice by crop calendar, a realistic service radius and diversification address this.

Question 10 · medium

Under India's mechanisation subsidy schemes, a machine is generally eligible for subsidy only if it:

  1. Has been tested and reported on by a recognised testing institution
  2. Is imported rather than made in India
  3. Is bought through a single national dealer
  4. Has an engine above a fixed power threshold
Answer and working

A. Has been tested and reported on by a recognised testing institution

Scheme guidelines generally require test reports from recognised institutes, such as the Farm Machinery Training and Testing Institutes, to protect buyers and public money. Exact rules are in the current operational guidelines.

A study plan for Farm Machinery Management & Economics in Rajasthan PSC

This plan follows where our questions actually fall, so the time goes where the marks are likely to be. It is our reading of the syllabus, not the exam body's weighting.

  1. First, the heavy units (52% of the 42 questions): Custom hiring centre economics (7, 17%); Mechanisation policy and subsidies (6, 14%); Break-even use and custom-hire comparison (5, 12%); Theoretical and effective field capacity (4, 10%).

    Read the manual chapters for these first and do every worked question you can find on them.

  2. Then the middle band: Variable costs: repair and maintenance, fuel and labour (4, 10%); Field efficiency and timeliness (3, 7%); Fixed costs: depreciation, interest, taxes, insurance and housing (3, 7%); Machinery selection and sizing (3, 7%).

    Aim for one sitting per unit, then mixed questions across them.

  3. Then the lighter units: Tractor-implement matching (3, 7%); Depreciation methods: straight line, declining balance, sum-of-years digits (2, 5%); Replacement decisions (2, 5%).

    Learn the definitions, classifications and standard numbers; these units are more often recalled than worked.

  4. Leave time for the hard ones: Variable costs: repair and maintenance, fuel and labour (1 hard of 4), Mechanisation policy and subsidies (1 hard of 6), Custom hiring centre economics (1 hard of 7).

    Come back to these after a first pass, untimed, and read every explanation, including for the options you rejected.

  5. Bank the easy marks: Theoretical and effective field capacity (4 easy of 4); Fixed costs: depreciation, interest, taxes, insurance and housing (3 easy of 3).

    Do these early in revision so they are fast on the day.

  6. Finish timed. Sit the subject as a timed set without notes, mark it, and send each wrong answer back to its unit above.

Last updated · How Laisha writes and checks its pages · Report a mistake

Ask Laisha about this

Opens Laisha's chat with your question ready to send. Sign in or start free.

Unlock every question — Rajasthan PSC Farm Machinery Management & Economics

US$10 a month · one price worldwide · cancel any time

  • Every practice question in this subject, with full working
  • Timed exam papers and progress by unit
  • Ask Laisha to explain any answer — up to 1,000 questions a month
Free or Smarter
FreeSmarter
Grow guides, pest pages, articlesRead allRead all
Ask Laisha5 a dayUp to 1,000 a month
Exam practiceThe sample on each pageEvery question, timed papers
Crop calendar and pest alerts—For your own fields
Calculators and tools—All
Uploads and reports—100 a month, real files
10 days free for every new account, no card.