LAISHA
Open Laisha

GATE Farm Machinery Management & Economics: practice questions

GATE — Agricultural Engineering (AG) · India · IITs and IISc on rotation (2027: IIT Madras)

Original practice questions written to the published syllabus · not past papers
10worked here, free
34written to this exam in this subject
10syllabus units

About GATE

GATE — Agricultural Engineering (AG) is a postgraduate admission exam run by IITs and IISc on rotation (2027: IIT Madras), for candidates in India. Computer-based, 3 hours, 100 marks (15 General Aptitude + 85 technical: 25 one-mark and 30 two-mark questions). MCQ, MSQ and NAT; negative marking on MCQ only (−1/3 for one-mark, −2/3 for two-mark); no partial credit on MSQ. On-screen virtual calculator.

Source: gate2027.iitm.ac.in.

Checked against the exam body's published information. Formats and fees change; confirm the current edition there before you book.

Farm Machinery Management & Economics in GATE

Numerical answer items on theoretical and effective field capacity, field efficiency, cost of operation per hour, depreciation by straight line, declining balance and sum-of-years digits, and break-even area or hours for owning against custom hire.

Choosing, sizing, costing and replacing machines, and running a custom hiring centre that pays.

Our 34 GATE questions in this subject: 2 easy, 23 medium, 9 hard, across 10 units.

10 practice questions, worked

Choose an answer, then open the working. Each explanation says why the right answer is right and why the others are not.

These 10 were written to GATE and are not shown on any other exam's page.

Question 1 · medium

A mower with 2.1 m cutting width works at 7 km/h and mows a 5 ha field in 4 h of total field time. What is its field efficiency?

  1. 85.0 %
  2. 117.6 %
  3. 15.0 %
  4. 8.5 %
Answer and working

A. 85.0 %

Theoretical capacity = 7 × 2.1 / 10 = 1.47 ha/h; effective capacity = 5 / 4 = 1.25 ha/h; efficiency = 1.25 / 1.47 = 85.0 %. Inverting the ratio gives 117.6 %, impossible because efficiency cannot exceed 100 %. 15.0 % is the lost fraction, 1 − 0.85; 8.5 % forgets the divisor 10 in the theoretical capacity (1.25/14.7).

Question 2 · medium

For the same power tiller (price 650,000, salvage 65,000) with interest at 12 %, what is the annual interest charge on average investment?

  1. 78,000
  2. 70,200
  3. 42,900
  4. 35,100
Answer and working

C. 42,900

Average investment = (P + S)/2 = (650,000 + 65,000)/2 = 357,500; interest = 357,500 × 0.12 = 42,900. Charging on full price gives 78,000; using (P − S)/2 gives 35,100. 70,200 charges interest on P − S (585,000 × 0.12).

Question 3 · medium

A machine costing 1,000,000 with a 10-year life is depreciated by the double-declining-balance method. What is its book value at the end of year 3?

  1. 488,000
  2. 512,000
  3. 640,000
  4. 400,000
Answer and working

B. 512,000

Book value = P(1 − r)³ = 1,000,000 × 0.8³ = 512,000. 488,000 is the accumulated depreciation, not the book value; 400,000 wrongly subtracts 20 % of the original price three times. 640,000 is the book value at the end of year 2 (1,000,000 × 0.8²).

Question 4 · hard

A thresher costs 400,000, has salvage 40,000 after 8 years, and the sinking fund earns 8 %. What annual deposit is required under the sinking-fund method?

  1. 37,606
  2. 33,845
  3. 45,000
  4. 62,645
Answer and working

B. 33,845

Deposit = (P − S) × i / [(1 + i)^L − 1] = 360,000 × 0.08 / (1.08⁸ − 1) = 360,000 × 0.08 / 0.8509 = 33,845. Straight line gives 45,000; using the capital recovery factor gives 62,645, which includes interest on the investment rather than accumulating a fund; ignoring salvage gives 37,606.

Question 5 · medium

A combine costs 500,000, has an 8-year life and 50,000 salvage. What is its book value at the end of year 4 by sum-of-years digits?

  1. 175,000
  2. 375,000
  3. 325,000
  4. 275,000
Answer and working

A. 175,000

Fractions for years 1–4 = (8 + 7 + 6 + 5)/36 = 26/36; accumulated depreciation = 26/36 × 450,000 = 325,000; book value = 500,000 − 325,000 = 175,000. Straight line gives 275,000; ascending digits (1 + 2 + 3 + 4 = 10) give 375,000.

Question 6 · medium

A machine's resale value is 580,000 at the end of year 3 and 500,000 at the end of year 4, and its repairs in year 4 cost 110,000. Its minimum average annual cost (over 3 years) is 183,333. What is the marginal cost of keeping it for year 4 (loss in resale value during year 4 plus repairs in year 4)?

  1. 610,000
  2. 185,000
  3. 110,000
  4. 190,000
Answer and working

D. 190,000

Marginal cost = (580,000 − 500,000) + 110,000 = 190,000. It exceeds the minimum average of 183,333, confirming replacement after year 3. 110,000 is repairs only; 185,000 is the 4-year average, not the marginal cost. 610,000 adds the resale value itself to the repairs (500,000 + 110,000).

Question 7 · medium

A 3-bottom plough with 30 cm bottoms works at 15 cm depth in soil with a specific resistance of 0.8 kgf/cm², at 4.5 km/h. What drawbar power is needed?

  1. 10.59 kW
  2. 1.35 kW
  3. 47.7 kW
  4. 13.24 kW
Answer and working

D. 13.24 kW

Cross-section = 3 × 30 × 15 = 1,350 cm²; draft = 0.8 × 1,350 = 1,080 kgf = 10.59 kN. Power = 10.59 × 4.5 / 3.6 = 13.24 kW. Forgetting the 3.6 conversion gives 47.7 kW; 10.59 is the draft in kN, not power; 1.35 treats kgf as newtons, leaving out g (1,080 N × 1.25 m/s = 1.35 kW).

Question 8 · hard

A disc harrow needs 18 kW of drawbar power. With a drawbar-to-PTO ratio of 0.70 and a design load of 85 % of rated PTO power, what minimum rated PTO power should the tractor have?

  1. 25.7 kW
  2. 21.2 kW
  3. 10.7 kW
  4. 30.3 kW
Answer and working

D. 30.3 kW

PTO needed = 18/0.70 = 25.7 kW; rated = 25.7/0.85 = 30.3 kW. Leaving out the reserve gives 25.7 kW; leaving out the power ratio gives 21.2 kW. 10.7 kW multiplies by both factors instead of dividing (18 × 0.70 × 0.85).

Question 9 · medium

A tractor can deliver 15 kW at the drawbar at 6 km/h. A harrow has a draft of 3.0 kN per metre of width. What is the widest harrow it can pull at that speed?

  1. 5.0 m
  2. 30 m
  3. 0.83 m
  4. 3.0 m
Answer and working

D. 3.0 m

Available pull = power × 3.6 / speed = 15 × 3.6 / 6 = 9.0 kN; width = 9.0 / 3.0 = 3.0 m. 5.0 m divides power by draft per metre, ignoring speed. 30 m is a factor-of-ten slip; 0.83 m forgets the 3.6 conversion (15/6/3.0).

Question 10 · medium

A CHC combine set has annual fixed cost 300,000 and variable cost 1,000 per hour; it rents at 1,500 per hour. How many hours a year must it be rented to break even?

  1. 200 h
  2. 300 h
  3. 120 h
  4. 600 h
Answer and working

D. 600 h

Break-even hours = FC/(price − VC) = 300,000/500 = 600 h. Dividing by the rent alone gives 200 h, ignoring the variable cost of each hour. 300 h divides by the variable cost (300,000/1,000), and 120 h by price plus variable cost (300,000/2,500).

A study plan for Farm Machinery Management & Economics in GATE

This plan follows where our questions actually fall, so the time goes where the marks are likely to be. It is our reading of the syllabus, not the exam body's weighting.

  1. First, the heavy units (53% of the 34 questions): Depreciation methods: straight line, declining balance, sum-of-years digits (7, 21%); Theoretical and effective field capacity (4, 12%); Tractor-implement matching (4, 12%); Break-even use and custom-hire comparison (3, 9%).

    Read the manual chapters for these first and do every worked question you can find on them.

  2. Then the middle band: Field efficiency and timeliness (3, 9%); Fixed costs: depreciation, interest, taxes, insurance and housing (3, 9%); Replacement decisions (3, 9%); Variable costs: repair and maintenance, fuel and labour (3, 9%).

    Aim for one sitting per unit, then mixed questions across them.

  3. Then the lighter units: Custom hiring centre economics (2, 6%); Machinery selection and sizing (2, 6%).

    Learn the definitions, classifications and standard numbers; these units are more often recalled than worked.

  4. Leave time for the hard ones: Custom hiring centre economics (1 hard of 2), Machinery selection and sizing (1 hard of 2), Break-even use and custom-hire comparison (1 hard of 3).

    Come back to these after a first pass, untimed, and read every explanation, including for the options you rejected.

  5. Bank the easy marks: Variable costs: repair and maintenance, fuel and labour (1 easy of 3); Theoretical and effective field capacity (1 easy of 4).

    Do these early in revision so they are fast on the day.

  6. Finish timed. Sit the subject as a timed set without notes, mark it, and send each wrong answer back to its unit above.

Last updated · How Laisha writes and checks its pages · Report a mistake

Ask Laisha about this

Opens Laisha's chat with your question ready to send. Sign in or start free.

Unlock every question — GATE Farm Machinery Management & Economics

US$10 a month · one price worldwide · cancel any time

  • Every practice question in this subject, with full working
  • Timed exam papers and progress by unit
  • Ask Laisha to explain any answer — up to 1,000 questions a month
Free or Smarter
FreeSmarter
Grow guides, pest pages, articlesRead allRead all
Ask Laisha5 a dayUp to 1,000 a month
Exam practiceThe sample on each pageEvery question, timed papers
Crop calendar and pest alerts—For your own fields
Calculators and tools—All
Uploads and reports—100 a month, real files
10 days free for every new account, no card.