Rajasthan PSC — Assistant Agriculture Engineer (Agriculture Engineering syllabus) · India · Rajasthan Public Service Commission
Original practice questions written to the published syllabus · not past papersRajasthan PSC — Assistant Agriculture Engineer (Agriculture Engineering syllabus) is a government recruitment exam run by Rajasthan Public Service Commission, for candidates in India. Objective paper; the paper structure was not captured.
Source: rpsc.rajasthan.gov.in.
Checked against the exam body's published information. Formats and fees change; confirm the current edition there before you book.
Oil hydraulics on tractors and machines: pumps, motors, cylinders, valves and circuits.
Our 41 Rajasthan PSC questions in this subject: 17 easy, 20 medium, 4 hard, across 9 units.
Choose an answer, then open the working. Each explanation says why the right answer is right and why the others are not.
These 10 were written to Rajasthan PSC and are not shown on any other exam's page.
A tractor works in a region where it starts at −5 °C in the morning and runs at high oil temperature by afternoon. Which property of the hydraulic fluid matters most for keeping viscosity acceptable across this range?
C. A high viscosity index
The viscosity index describes how little the viscosity changes with temperature; a high-VI fluid stays thin enough to pump at a cold start and thick enough to seal when hot. Flash point concerns fire risk, bulk modulus concerns stiffness, and specific gravity concerns density, none of which controls viscosity change with temperature.
A pump on an older tractor makes a loud gravelly, rattling noise on cold mornings that fades as the oil warms. The oil does not look foamy. The most likely cause is
A. cavitation, with thick cold oil starving the inlet
Cold, viscous oil raises suction losses, so inlet pressure falls below the vapour and air-release level and bubbles collapse violently as they reach the outlet: cavitation, with its gravelly noise. Aeration usually gives foamy oil and a whine, and comes from leaks on the suction side, since a pressure-line leak sprays oil out rather than drawing air in. A high relief setting or a worn pump does not produce noise that fades as oil warms.
In a closed-loop hydrostatic transmission on a self-propelled sprayer, the charge pump's job is to
A. keep the low-pressure side above a set minimum and make up leakage losses
In a closed loop the motor returns oil directly to the pump inlet, so leakage to the cases must be made up and the low side must be kept pressurised to prevent cavitation; the charge pump does both and brings in filtered, cooled oil. The main pump drives the motors, crossover relief valves deal with pressure peaks, and case drains go through the cooler to the reservoir.
A tipping-trailer cylinder with a 100 mm bore and a 500 mm stroke is extended by a tractor remote supplying 25 L/min. Neglecting compressibility and leakage, the time to extend fully is about
A. 9.4 s
Swept volume = π(0.1)²/4 × 0.5 = 3.927 L. Time = 3.927/25 min = 0.1571 min = 9.4 s. 0.157 is the time in minutes written as seconds; treating the bore as a radius gives 37.7; 2.36 uses half the bore as the diameter.
In an open-centre tractor hydraulic system with all control valves in neutral,
A. pump flow returns to tank at low pressure through the valve centres
Open-centre valves have a through passage in neutral, so a fixed pump circulates its full flow to tank at only the pressure needed to overcome line and valve losses. High standby pressure with no flow describes a pressure-compensated closed-centre system; flow over the relief would overheat the oil; accumulator unloading is a different closed-centre arrangement.
On a tractor whose single pump supplies both power steering and implement hydraulics, which valve ensures the steering is always supplied first?
C. A priority flow-control valve
A priority valve sends the flow the steering demands to the steering circuit first and passes the excess to the other functions. A reducing valve limits branch pressure, a counterbalance valve holds an overrunning load, and a pilot-operated check holds a cylinder.
Which linkage control mode is most suitable for a mounted boom sprayer, which must stay at a set height above the crop?
C. Position control
Position control holds the implement at a fixed height relative to the tractor regardless of load, which is what a sprayer, mower or transport needs. Draft control would move the boom as forces changed, float lets it drop to the ground, and intermix blends in a draft signal the sprayer does not need.
A tractor's lift cylinder takes in 1.2 L of oil to raise the linkage from fully down to fully up. The pump supplies 30 L/min to the lift. The time to raise the linkage fully is about
B. 2.4 s
t = V/Q = 1.2 L/30 L/min = 0.04 min = 2.4 s. 0.04 is the time in minutes; 25 is Q/V; 144 multiplies by 3600 instead of 60.
Larger tractors with closed-centre load-sensing hydraulics commonly use which type of main pump?
D. Variable-displacement axial-piston pump
Load sensing needs a pump whose displacement can be varied by its LS compensator, usually a swash-plate axial-piston pump. Gear and balanced vane pumps are fixed-displacement and are used in open-centre systems; centrifugal pumps are not positive-displacement and are not used for power hydraulics.
Which is the safest practice when a farmer needs to work under a mounted rotary tiller held up on the tractor's three-point linkage?
C. Lower it onto solid stands so it is held mechanically, never by hydraulics alone
Hydraulic holding can fail through valve leakage, a burst hose or someone touching a lever; only mechanical support is safe. A running pump, position control or a closed drop-rate valve all still rely on hydraulics, and spool valves leak.
This plan follows where our questions actually fall, so the time goes where the marks are likely to be. It is our reading of the syllabus, not the exam body's weighting.
Read the manual chapters for these first and do every worked question you can find on them.
Aim for one sitting per unit, then mixed questions across them.
Learn the definitions, classifications and standard numbers; these units are more often recalled than worked.
Come back to these after a first pass, untimed, and read every explanation, including for the options you rejected.
Do these early in revision so they are fast on the day.
Last updated · How Laisha writes and checks its pages · Report a mistake
US$10 a month · one price worldwide · cancel any time
| Free | Smarter | |
|---|---|---|
| Grow guides, pest pages, articles | Read all | Read all |
| Ask Laisha | 5 a day | Up to 1,000 a month |
| Exam practice | The sample on each page | Every question, timed papers |
| Crop calendar and pest alerts | — | For your own fields |
| Calculators and tools | — | All |
| Uploads and reports | — | 100 a month, real files |
An AI operating system for agriculture: free guides, manuals and tools written for every country.