LAISHA
Open Laisha

ICAR AICE-JRF/SRF Post-Harvest Engineering of Cereals, Pulses & Oilseeds: practice questions

ICAR AICE-JRF/SRF (PhD) — Agricultural Engineering subjects 38–43 · India · National Testing Agency for ICAR

Original practice questions written to the published syllabus · not past papers
10worked here, free
40written to this exam in this subject
15syllabus units

About ICAR AICE-JRF/SRF

ICAR AICE-JRF/SRF (PhD) — Agricultural Engineering subjects 38–43 is a PhD, fellowship and lectureship exam run by National Testing Agency for ICAR, for candidates in India. LAN-based computer test, 2 hours, 120 MCQs: 20 Part A (general knowledge and reasoning), 50 Part B (core group), 50 Part C (specialisation); four options.

Source: icar.org.in.

Checked against the exam body's published information. Formats and fees change; confirm the current edition there before you book.

Post-Harvest Engineering of Cereals, Pulses & Oilseeds in ICAR AICE-JRF/SRF

Units on post-harvest unit operations, process technology and machinery and design of processing machinery ask for PG depth: sorption models (GAB, BET, modified Henderson), thin-layer and diffusion models and effective diffusivity, deep-bed models, dryer design and performance indices, parboiling kinetics and quality, extraction and refining steps, and design relations for conveyors and mills.

Moisture, drying, parboiling, milling, cleaning, size reduction and conveying of grains, pulses and oilseeds.

Our 40 ICAR AICE-JRF/SRF questions in this subject: 1 easy, 20 medium, 19 hard, across 15 units.

10 practice questions, worked

Choose an answer, then open the working. Each explanation says why the right answer is right and why the others are not.

These 10 were written to ICAR AICE-JRF/SRF and are not shown on any other exam's page.

Question 1 · medium

At a high-altitude site (lower barometric pressure), air with the same dry-bulb temperature and the same water-vapour partial pressure as at sea level has

  1. a higher humidity ratio
  2. the same humidity ratio as at sea level
  3. a lower relative humidity
  4. a lower dew-point temperature
Answer and working

A. a higher humidity ratio

W = 0.622 p_v/(P − p_v): a smaller P makes the denominator smaller, so W is higher. RH is p_v/p_vs, which depends only on temperature and p_v, so it is unchanged. This is why sea-level charts must be corrected. With p_v unchanged the dew point is also unchanged.

Question 2 · hard

In the constant-rate period, the convective heat-transfer coefficient is 40 W/m²·K, the air is at 70 °C and its wet-bulb temperature is 35 °C. Taking latent heat as 2,400 kJ/kg, the drying rate is closest to

  1. 2100 kg/(m²·h)
  2. 0.0006 kg/(m²·h)
  3. 4.20 kg/(m²·h)
  4. 2.10 kg/(m²·h)
Answer and working

D. 2.10 kg/(m²·h)

R_c = h(T_a − T_wb)/λ = 40 × 35/2.4 × 10⁶ = 5.833e-04 kg/m²·s × 3600 = 2.10 kg/m²·h. Using the air temperature instead of the difference gives 4.20; leaving the answer per second is a unit slip. Using λ in kJ/kg with h in W gives a value 1,000 times too large (2100).

Question 3 · hard

Treating a grain kernel as a sphere of radius 2 mm, the late-period plot of ln MR against time (s) has a slope of −1.2 × 10⁻⁴ s⁻¹. The effective moisture diffusivity is closest to

  1. 4.80e-10 m²/s
  2. 1.95e-10 m²/s
  3. 4.86e-11 m²/s
  4. 1.53e-10 m²/s
Answer and working

C. 4.86e-11 m²/s

First term of the sphere solution: ln MR = ln(6/π²) − (π²D/r²)t, so D = |slope|·r²/π² = 1.2 × 10⁻⁴ × (2 × 10⁻³)²/9.8696 = 4.86e-11 m²/s, within the usual 10⁻¹¹–10⁻¹⁰ range for grains. Omitting π² gives 4.80e-10; using the diameter instead of the radius gives a value four times too large.

Question 4 · hard

Effective diffusivity of paddy is 3.0 × 10⁻¹¹ m²/s at 40 °C and 6.0 × 10⁻¹¹ m²/s at 60 °C. The Arrhenius activation energy is closest to

  1. 0.692 kJ/mol
  2. 13.1 kJ/mol
  3. 69.2 kJ/mol
  4. 30.1 kJ/mol
Answer and working

D. 30.1 kJ/mol

E_a = R ln(D₂/D₁)/(1/T₁ − 1/T₂) = 8.314 × 0.6931/(1/313.15 − 1/333.15) = 8.314 × 0.6931/1.9171e-04 = 30061 J/mol ≈ 30.1 kJ/mol. Using Celsius temperatures gives a nonsense small value; multiplying by 2.303 treats the natural log as a common log. 13.1 kJ/mol uses log₁₀ 2 instead of ln 2; 0.692 kJ/mol is the Celsius result; 69.2 kJ/mol multiplies by 2.303.

Question 5 · medium

In the Page thin-layer model MR = exp(−k tⁿ), the exponent n

  1. is an empirical shape parameter letting the curve depart from a simple exponential
  2. is the activation energy divided by RT
  3. must equal 1 for grains
  4. is the number of terms retained from the series solution of Fick's second law of diffusion
Answer and working

A. is an empirical shape parameter letting the curve depart from a simple exponential

Page added n to Lewis's exponential to improve fit; n = 1 reduces it to the Lewis model. It has no direct physical meaning, unlike k, which follows Arrhenius behaviour.

Question 6 · medium

A three-parameter thin-layer model gives R² = 0.998 and a two-parameter model R² = 0.996 on the same data. The sound conclusion is that

  1. RMSE, reduced chi-square and parameter count must also be weighed before preferring the first model
  2. R² differences below 0.01 mean both models are wrong
  3. the two-parameter model must be rejected
  4. the three-parameter model is proven physically correct, because a higher R² always means a better mechanism
Answer and working

A. RMSE, reduced chi-square and parameter count must also be weighed before preferring the first model

Adding parameters always raises R², so small gains are not evidence of a better model. Reduced chi-square and RMSE penalise extra parameters; physical plausibility also matters.

Question 7 · hard

Smooth crushing rolls of 500 mm diameter are set with a 10 mm gap and fed 30 mm particles. The minimum coefficient of friction needed for the particles to be nipped is closest to

  1. 0.283
  2. 0.615
  3. 0.197
  4. 0.272
Answer and working

A. 0.283

cos b = (R + d)/(R + r) = (250 + 5)/(250 + 15) = 0.9623, so the half nip angle b = 15.79°, and μ ≥ tan b = 0.283. Using the full nip angle gives 0.615; using the full gap instead of half the gap gives 0.197. 0.272 is sin b instead of tan b.

Question 8 · medium

Ground feed has a fineness modulus of 3.0. Using the Henderson–Perry relation D = 0.104 × 2^FM, the average particle size is closest to

  1. 0.62 mm
  2. 0.0328 mm
  3. 0.94 mm
  4. 0.83 mm
Answer and working

D. 0.83 mm

D = 0.104 × 2³ = 0.832 mm. 0.0041 × 2^FM gives inches (0.0328 in), not millimetres; the other options misapply the exponent. 0.62 mm multiplies 2 by FM instead of raising it (0.104 × 6); 0.94 mm squares FM (0.104 × 3²).

Question 9 · hard

A screw conveyor has a 0.30 m flight diameter, 0.06 m shaft, 0.30 m pitch, runs at 60 rpm with a loading factor of 0.30, and handles grain of 750 kg/m³. Its capacity is closest to

  1. 16.5 t/h
  2. 0.27 t/h
  3. 17.2 t/h
  4. 55.0 t/h
Answer and working

A. 16.5 t/h

Q = (π/4)(D² − d²)·p·N·ρ·φ = 0.7854 × (0.09 − 0.0036) × 0.30 × 60 × 750 × 0.30 = 274.8 kg/min = 16.5 t/h. Ignoring the shaft gives 17.2 t/h; ignoring the loading factor gives 55.0 t/h (a full trough). 0.27 t/h is the 274.8 kg/min read as t/min and mislabelled.

Question 10 · medium

In horizontal dilute-phase pneumatic conveying of grain, if the air velocity falls below the saltation velocity,

  1. the cyclone stops separating
  2. the grain accelerates and moves faster than the conveying air in the pipe
  3. particles drop out of suspension and form deposits or dunes in the pipe
  4. the system switches to positive pressure
Answer and working

C. particles drop out of suspension and form deposits or dunes in the pipe

Saltation velocity is the minimum horizontal velocity to keep particles suspended; below it they settle and can block the line. The vertical equivalent is the choking velocity.

A study plan for Post-Harvest Engineering of Cereals, Pulses & Oilseeds in ICAR AICE-JRF/SRF

This plan follows where our questions actually fall, so the time goes where the marks are likely to be. It is our reading of the syllabus, not the exam body's weighting.

  1. First, the heavy units (65% of the 40 questions): Thin-layer drying models (7, 18%); Equilibrium moisture content and sorption isotherms (6, 15%); Size reduction: Rittinger, Kick and Bond laws (5, 13%); Drying theory: constant and falling rate periods (4, 10%); Oil expression and solvent extraction (4, 10%).

    Read the manual chapters for these first and do every worked question you can find on them.

  2. Then the middle band: Cleaning, grading and screening effectiveness (2, 5%); Conveying: belt, bucket, screw and pneumatic (2, 5%); Psychrometry and properties of air (2, 5%); Seed processing (2, 5%); Grain dryers: bin, LSU, recirculating, fluidised-bed and solar (1, 3%).

    Aim for one sitting per unit, then mixed questions across them.

  3. Then the lighter units: Moisture content: wet and dry basis (1, 3%); Paddy and rice milling: husking, whitening, polishing and yields (1, 3%); Parboiling and hydrothermal treatment (1, 3%); Pulse milling (1, 3%); Wheat milling (1, 3%).

    Learn the definitions, classifications and standard numbers; these units are more often recalled than worked.

  4. Leave time for the hard ones: Cleaning, grading and screening effectiveness (2 hard of 2), Moisture content: wet and dry basis (1 hard of 1), Paddy and rice milling: husking, whitening, polishing and yields (1 hard of 1).

    Come back to these after a first pass, untimed, and read every explanation, including for the options you rejected.

  5. Bank the easy marks: Equilibrium moisture content and sorption isotherms (1 easy of 6).

    Do these early in revision so they are fast on the day.

  6. Finish timed. Sit the subject as a timed set without notes, mark it, and send each wrong answer back to its unit above.

Last updated · How Laisha writes and checks its pages · Report a mistake

Ask Laisha about this

Opens Laisha's chat with your question ready to send. Sign in or start free.

Unlock every question — ICAR AICE-JRF/SRF Post-Harvest Engineering of Cereals, Pulses & Oilseeds

US$10 a month · one price worldwide · cancel any time

  • Every practice question in this subject, with full working
  • Timed exam papers and progress by unit
  • Ask Laisha to explain any answer — up to 1,000 questions a month
Free or Smarter
FreeSmarter
Grow guides, pest pages, articlesRead allRead all
Ask Laisha5 a dayUp to 1,000 a month
Exam practiceThe sample on each pageEvery question, timed papers
Crop calendar and pest alerts—For your own fields
Calculators and tools—All
Uploads and reports—100 a month, real files
10 days free for every new account, no card.