Farm Machinery Training & Testing Institutes (Budni, Hisar, Anantapur, Biswanath Chariali) · India · Ministry of Agriculture & Farmers Welfare, Government of India
Original practice questions written to the published syllabus · not past papersFarm Machinery Training & Testing Institutes (Budni, Hisar, Anantapur, Biswanath Chariali) is a professional certification run by Ministry of Agriculture & Farmers Welfare, Government of India, for candidates in India. Not an exam: short training courses and machinery testing (commercial, batch, confidential, CMVR).
Official site: nerfmtti.nic.in.
We have not been able to confirm these details against the exam body's own specification, so fees, dates and pass marks are left out on purpose. Check the current format, eligibility, fees and dates on the official site.
Reading and making drawings of machine parts and buildings, by hand and in CAD.
Our 27 Farm Machinery Training & Testing Institutes questions in this subject: 9 easy, 10 medium, 8 hard, across 7 units.
Choose an answer, then open the working. Each explanation says why the right answer is right and why the others are not.
These 10 were written to Farm Machinery Training & Testing Institutes and are not shown on any other exam's page.
A dimension is given as 50 +0.05 / −0.02 mm. What are the upper limit, lower limit and tolerance?
B. 50.05 mm, 49.98 mm, 0.07 mm
Upper = 50 + 0.05 = 50.05; lower = 50 − 0.02 = 49.98; tolerance = 50.05 − 49.98 = 0.07 mm. 0.03 mm subtracts the deviations instead of spanning them.
On a surface texture symbol, what does a horizontal bar closing the basic tick symbol indicate?
A. Material removal by machining is required
The bar closing the symbol requires material removal. A circle inside the symbol prohibits removal (leave as cast, forged or rolled). The basic open symbol alone allows any process.
An old drawing of a bearing seat specifies roughness grade N7. What Ra value does this correspond to?
B. 1.6 µm
The N grades double Ra at each step: N6 = 0.8, N7 = 1.6, N8 = 3.2 µm. N7 is not 7 µm; the number is a grade, not a value. The N grades are no longer in the current ISO standard but remain on many legacy drawings.
The lateral surface of a cylindrical duct of diameter 200 mm and length 500 mm is to be cut from flat sheet. Ignoring the seam allowance, what are the dimensions of the development?
B. A rectangle 628.3 mm × 500 mm
A cylinder develops by the parallel-line method into a rectangle whose length is the circumference πD = π × 200 = 628.3 mm and whose width is the height. Using the diameter or the radius (πD/2) leaves the duct unable to close; 2πD uses the diameter in place of the radius.
A right square pyramid has a base side of 60 mm and a vertical height of 80 mm. In its development, what is the true length of each slant edge?
A. 90.6 mm
The slant edge runs from the apex to a corner, which is half the base diagonal from the axis: 60√2/2 = 42.43 mm. So edge = √(80² + 42.43²) = 90.6 mm. √(80² + 30²) = 85.4 mm is the slant height of a face (apex to mid-side), not the edge. Using the full 60 mm base side as the horizontal offset gives √(80² + 60²) = 100.0 mm.
Which key allows a hub to slide axially along a shaft while still transmitting torque?
C. Feather key
A feather (parallel) key is fixed to the shaft or hub and permits axial sliding. A taper key and gib-head key lock the hub axially by wedging; a saddle key relies on friction and cannot slide reliably under torque.
On an assembly drawing, what is the purpose of the numbered circles (balloons) attached to the parts by leaders?
B. They give each part an item number that refers to the parts list
Balloons carry item numbers that link each part to its line in the parts list (bill of materials), which gives name, material, quantity and drawing or standard number. Operation sequence, weld inspection and lubrication are given elsewhere.
Which dimensions does an assembly drawing normally carry?
A. Only assembly and installation dimensions, such as overall size
Detail drawings fully define each part; the assembly drawing shows how parts fit and gives overall, mounting and critical assembly dimensions. Duplicating every detail dimension invites conflict.
A hub bore is drawn as ⌀35 H7 and the matching shaft as ⌀35 p6. During a field repair the mechanic finds the hub slides on by hand. What is the most likely conclusion?
D. A part is out of tolerance, since H7/p6 is meant to be an interference fit
In standard textbook use H7/p6 is a light press (interference) fit, so a hand-sliding hub indicates a worn shaft, an oversize bore or a wrong part. H7/g6 would be a sliding clearance fit. H can be combined with any shaft letter in the hole-basis system.
In an exploded pictorial view in a spare-parts catalogue, how are the parts arranged?
C. Separated along their assembly axes, in the order in which they fit together
Exploded views move parts apart along the lines of assembly so that the order and relationship are clear; item numbers then refer to the parts list.
This plan follows where our questions actually fall, so the time goes where the marks are likely to be. It is our reading of the syllabus, not the exam body's weighting.
Read the manual chapters for these first and do every worked question you can find on them.
Aim for one sitting per unit, then mixed questions across them.
Learn the definitions, classifications and standard numbers; these units are more often recalled than worked.
Come back to these after a first pass, untimed, and read every explanation, including for the options you rejected.
Do these early in revision so they are fast on the day.
Last updated · How Laisha writes and checks its pages · Report a mistake
US$10 a month · one price worldwide · cancel any time
| Free | Smarter | |
|---|---|---|
| Grow guides, pest pages, articles | Read all | Read all |
| Ask Laisha | 5 a day | Up to 1,000 a month |
| Exam practice | The sample on each page | Every question, timed papers |
| Crop calendar and pest alerts | — | For your own fields |
| Calculators and tools | — | All |
| Uploads and reports | — | 100 a month, real files |
An AI operating system for agriculture: free guides, manuals and tools written for every country.