LAISHA
Open Laisha

ICAR AIEEA-PG Tractor Systems & Controls: practice questions

ICAR AIEEA-PG — Agricultural Engineering & Technology (Major Subject Group 10) · India · National Testing Agency for ICAR

Original practice questions written to the published syllabus · not past papers
10worked here, free
54written to this exam in this subject
15syllabus units

About ICAR AIEEA-PG

ICAR AIEEA-PG — Agricultural Engineering & Technology (Major Subject Group 10) is a postgraduate admission exam run by National Testing Agency for ICAR, for candidates in India. Computer-based, 120 minutes, 120 MCQs, +4 / −1, English only (2026 bulletin). One paper for the whole subject group.

Source: icar.org.in.

Checked against the exam body's published information. Formats and fees change; confirm the current edition there before you book.

Tractor Systems & Controls in ICAR AIEEA-PG

Unit V farm power: identification of transmission components and their functions, PTO standards, hitch categories, brakes and steering types, hydraulic control modes, power tillers; mostly recall with short calculations.

Everything between the engine and the implement: clutch, gearbox, differential, PTO, brakes, steering, hydraulics, hitch and tyres.

Our 54 ICAR AIEEA-PG questions in this subject: 24 easy, 30 medium, 0 hard, across 15 units.

10 practice questions, worked

Choose an answer, then open the working. Each explanation says why the right answer is right and why the others are not.

These 10 were written to ICAR AIEEA-PG and are not shown on any other exam's page.

Question 1 · easy

A PTO dynamometer reads 250 N·m at 540 rev/min. The PTO power is

  1. 2.25 kW
  2. 26.18 kW
  3. 848 kW
  4. 14.14 kW
Answer and working

D. 14.14 kW

P = 2πNT/60,000 = 2π × 540 × 250/60,000 = 14.14 kW. Leaving out 2π gives 2.25; assuming a 1,000 rev/min shaft gives 26.18; not dividing rev/min by 60 gives a value sixty times too large.

Question 2 · medium

A power tiller engine runs at 2200 rev/min; the overall reduction to the wheels is 60:1 and the pneumatic wheel diameter is 0.6 m. The theoretical forward speed is

  1. 4.15 km/h
  2. 8.29 km/h
  3. 1.15 km/h
  4. 69.1 km/h
Answer and working

A. 4.15 km/h

Wheel speed = 2200/60 = 36.67 rev/min. v = πDN = π × 0.6 × 36.67 = 69.1 m/min = 4.15 km/h. Treating 0.6 m as a radius doubles it; 1.15 is in m/s; 69.1 is m/min mislabelled.

Question 3 · easy

Which tractor type steers by hinging the frame between the front and rear axles?

  1. Row-crop 2WD tractor
  2. MFWD tractor
  3. Articulated four-wheel-drive tractor
  4. Orchard tractor
Answer and working

C. Articulated four-wheel-drive tractor

Articulated 4WD tractors have equal-size wheels on rigid axles and steer by a central hinge with hydraulic cylinders. The others use steered front wheels.

Question 4 · easy

A row-crop tractor differs from a general utility tractor mainly in having

  1. a lower centre of gravity and a narrow fixed track for working under orchard trees
  2. high crop clearance and adjustable track width to straddle crop rows
  3. articulated steering and a single fixed track width
  4. no PTO
Answer and working

B. high crop clearance and adjustable track width to straddle crop rows

Row-crop tractors are built to work between and over crop rows: high clearance and adjustable wheel track. Low and narrow build is the orchard tractor.

Question 5 · easy

In a dual (two-stage) clutch, pressing the pedal half way

  1. stops drive to the transmission while the PTO keeps running
  2. stops both transmission and PTO together, as a single-plate clutch would
  3. stops only the PTO while the tractor continues to travel
  4. engages the differential lock
Answer and working

A. stops drive to the transmission while the PTO keeps running

The first stage of pedal travel releases the transmission clutch; full travel also releases the PTO clutch. That is what makes the PTO 'live'.

Question 6 · medium

Constant-mesh gearboxes can use helical gears while sliding-mesh gearboxes normally use spur gears because

  1. helical gears are weaker
  2. spur gears are quieter and so are preferred wherever gears must be slid
  3. helical gears are hard to slide into mesh, but in constant mesh they never need to be
  4. helical gears need no bearings because their axial thrust cancels out in a constant-mesh train
Answer and working

C. helical gears are hard to slide into mesh, but in constant mesh they never need to be

Helical teeth produce axial thrust and cannot be slid into engagement easily; in constant mesh the gears stay meshed and dog clutches do the selecting, so quieter, stronger helical gears can be used.

Question 7 · easy

The standard rear PTO speeds defined by ISO 500 for field tractors are

  1. 750 and 1,500 rev/min
  2. 540 and 1,000 rev/min
  3. 540 and 1,500 rev/min
  4. 1,000 and 2,000 rev/min
Answer and working

B. 540 and 1,000 rev/min

ISO 500 (harmonised with ASABE S203/S205) defines 540 rev/min (type 1) and 1,000 rev/min (types 2 and 3 and larger) shafts.

Question 8 · medium

Caster in front-wheel geometry is

  1. the inward tilt of the wheel top
  2. the fore-and-aft tilt of the kingpin axis, giving a self-centring effect
  3. the difference in distance between the front and rear of the front tyres
  4. the inward tilt of the kingpin seen from the front
Answer and working

B. the fore-and-aft tilt of the kingpin axis, giving a self-centring effect

Caster tilts the steering axis back so the contact patch trails it, like a trolley wheel. The other options describe camber, toe-in and kingpin inclination.

Question 9 · medium

Float setting on a tractor hitch allows the implement to

  1. stay at a fixed height
  2. be raised to full height
  3. vibrate for better soil breaking
  4. follow the ground contour on its own gauge wheels or skids
Answer and working

D. follow the ground contour on its own gauge wheels or skids

In float the lift is free, so the implement rides on its own wheels or skids and follows the ground.

Question 10 · easy

A rollover protective structure (ROPS) protects the operator only if

  1. the seat belt is worn so the operator stays within the protective zone
  2. the tractor has a cab
  3. the tractor is MFWD
  4. the PTO is disengaged
Answer and working

A. the seat belt is worn so the operator stays within the protective zone

In an overturn an unbelted operator can be thrown out and crushed by the tractor or the ROPS itself. Belt and ROPS work together.

A study plan for Tractor Systems & Controls in ICAR AIEEA-PG

This plan follows where our questions actually fall, so the time goes where the marks are likely to be. It is our reading of the syllabus, not the exam body's weighting.

  1. First, the heavy units (48% of the 54 questions): Gearbox and transmission: sliding, constant and synchromesh (7, 13%); Differential and differential lock (5, 9%); Power take-off: standards and speeds (5, 9%); Steering geometry (Ackermann) and power steering (5, 9%); Draft and position control (4, 7%).

    Read the manual chapters for these first and do every worked question you can find on them.

  2. Then the middle band: Hydraulic system: open and closed centre (4, 7%); Tractor types and selection (4, 7%); Brakes (3, 6%); Clutch: single and dual plate (3, 6%); Final drive (3, 6%).

    Aim for one sitting per unit, then mixed questions across them.

  3. Then the lighter units: Power tillers (3, 6%); Tyres and ballasting (3, 6%); Operator controls and ROPS (2, 4%); Three-point hitch: categories, free and restrained links (2, 4%); CVT and power-shift transmissions (1, 2%).

    Learn the definitions, classifications and standard numbers; these units are more often recalled than worked.

  4. Bank the easy marks: CVT and power-shift transmissions (1 easy of 1); Hydraulic system: open and closed centre (3 easy of 4).

    Do these early in revision so they are fast on the day.

  5. Finish timed. Sit the subject as a timed set without notes, mark it, and send each wrong answer back to its unit above.

Last updated · How Laisha writes and checks its pages · Report a mistake

Ask Laisha about this

Opens Laisha's chat with your question ready to send. Sign in or start free.

Unlock every question — ICAR AIEEA-PG Tractor Systems & Controls

US$10 a month · one price worldwide · cancel any time

  • Every practice question in this subject, with full working
  • Timed exam papers and progress by unit
  • Ask Laisha to explain any answer — up to 1,000 questions a month
Free or Smarter
FreeSmarter
Grow guides, pest pages, articlesRead allRead all
Ask Laisha5 a dayUp to 1,000 a month
Exam practiceThe sample on each pageEvery question, timed papers
Crop calendar and pest alerts—For your own fields
Calculators and tools—All
Uploads and reports—100 a month, real files
10 days free for every new account, no card.