LAISHA
Open Laisha

ICAR AIEEA-PG Tractor & Automotive Engines (IC Engines): practice questions

ICAR AIEEA-PG — Agricultural Engineering & Technology (Major Subject Group 10) · India · National Testing Agency for ICAR

Original practice questions written to the published syllabus · not past papers
10worked here, free
50written to this exam in this subject
16syllabus units

About ICAR AIEEA-PG

ICAR AIEEA-PG — Agricultural Engineering & Technology (Major Subject Group 10) is a postgraduate admission exam run by National Testing Agency for ICAR, for candidates in India. Computer-based, 120 minutes, 120 MCQs, +4 / −1, English only (2026 bulletin). One paper for the whole subject group.

Source: icar.org.in.

Checked against the exam body's published information. Formats and fees change; confirm the current edition there before you book.

Tractor & Automotive Engines (IC Engines) in ICAR AIEEA-PG

Unit V farm power: engine systems (fuel, cooling, lubrication, ignition, governing), cycles, performance terms and tractor testing; more recall than GATE, with short calculations.

How tractor engines work and how their performance is measured — the single most reliably examined farm-power topic.

Our 50 ICAR AIEEA-PG questions in this subject: 20 easy, 26 medium, 4 hard, across 16 units.

10 practice questions, worked

Choose an answer, then open the working. Each explanation says why the right answer is right and why the others are not.

These 10 were written to ICAR AIEEA-PG and are not shown on any other exam's page.

Question 1 · medium

Which statement about SI and CI engines is correct?

  1. SI engines use higher compression ratios because petrol has a higher cetane number than diesel fuel
  2. CI engines use higher compression ratios because the air must be hot enough to ignite the injected fuel
  3. CI engines are throttled at part load in the same way as SI engines, using a butterfly valve in the intake
  4. SI engines ignite the charge by injecting fuel into hot compressed air
Answer and working

B. CI engines use higher compression ratios because the air must be hot enough to ignite the injected fuel

A CI engine needs a high compression ratio (roughly 14–22) to reach the fuel's self-ignition temperature, and it controls load by fuel quantity, not throttling. SI engines are limited to lower ratios by knock; petrol has a high octane, not a high cetane, number.

Question 2 · easy

The correct sequence of combustion stages in a CI engine is

  1. rapid combustion → ignition delay → after-burning → controlled combustion
  2. flame kernel → flame propagation → after-burning → ignition delay
  3. controlled (diffusion) combustion → ignition delay → rapid (premixed) combustion → after-burning
  4. ignition delay → rapid (premixed) combustion → controlled combustion → after-burning
Answer and working

D. ignition delay → rapid (premixed) combustion → controlled combustion → after-burning

Fuel mixed during the delay burns rapidly; later fuel burns as fast as it mixes (controlled); reactions finish during expansion (after-burning).

Question 3 · medium

Fitting a charge-air cooler (intercooler) after the turbocharger compressor

  1. increases charge temperature to shorten ignition delay and reduce diesel knock
  2. reduces boost pressure to protect the turbine
  3. increases charge density and lowers combustion temperature, reducing NOx
  4. is needed only on naturally aspirated engines
Answer and working

C. increases charge density and lowers combustion temperature, reducing NOx

Compression heats the air; cooling it raises density (more air per cycle) and lowers peak temperature, which cuts NOx formation.

Question 4 · medium

In the pressure (forced-feed) lubrication system of a tractor engine, oil reaches the big-end bearings through

  1. dippers on the connecting rods splashing from troughs
  2. oil mixed with the fuel
  3. drillings in the crankshaft from the main bearings
  4. the pushrods from the rocker shaft
Answer and working

C. drillings in the crankshaft from the main bearings

The pump feeds the main gallery and main bearings; drilled passages in the crankshaft carry oil from the mains to the crankpins. Dippers belong to splash systems.

Question 5 · easy

The governor normally fitted to an agricultural tractor diesel engine is

  1. a constant-speed governor only
  2. a limiting-speed (min–max) governor only
  3. an all-speed governor
  4. no governor, since the operator controls speed
Answer and working

C. an all-speed governor

The tractor governor holds whatever speed the hand throttle sets, from idle to maximum, so PTO machines run steadily. Constant-speed governors are for generator sets; min–max governors were used on road vehicles. This is also called a variable-speed governor.

Question 6 · easy

Hunting of a governor means

  1. continuous oscillation of engine speed above and below the set speed
  2. the governor's inability to bring the engine up to its maximum rated speed
  3. a gradual permanent fall in speed with load
  4. the speed range between idle and maximum
Answer and working

A. continuous oscillation of engine speed above and below the set speed

An over-sensitive governor over-corrects, so speed keeps swinging about the set value. A steady fall of speed with load is droop.

Question 7 · easy

The two reference fuels originally used to define the cetane scale are

  1. iso-octane (100) and n-heptane (0)
  2. n-heptane (100) and iso-octane (0)
  3. n-hexadecane (100) and alpha-methylnaphthalene (0)
  4. methanol (100) and ethanol (0)
Answer and working

C. n-hexadecane (100) and alpha-methylnaphthalene (0)

Cetane (n-hexadecane) = 100 and alpha-methylnaphthalene = 0; current practice uses heptamethylnonane (15) as the low reference. Iso-octane/n-heptane define the octane scale.

Question 8 · medium

Straight-chain paraffins, compared with aromatics of similar boiling range, make

  1. better petrol (higher octane) but poorer diesel fuels (lower cetane number)
  2. better fuels for both engine types
  3. poorer fuels for both engine types
  4. better diesel fuels (higher cetane) but poorer petrol (lower octane)
Answer and working

D. better diesel fuels (higher cetane) but poorer petrol (lower octane)

Straight chains break down and self-ignite easily: good for CI, bad for SI. Aromatics and branched paraffins resist self-ignition: good octane, poor cetane.

Question 9 · hard

At constant speed an engine has BP = 40 kW and FP = 10 kW. If the load is reduced to BP = 20 kW with friction power unchanged, the mechanical efficiency becomes

  1. 80.0%
  2. 50.0%
  3. 66.7%
  4. 40.0%
Answer and working

C. 66.7%

At 40 kW: ηm = 40/50 = 80%. At 20 kW: IP = 20 + 10 = 30 kW, ηm = 20/30 = 66.7%. Mechanical efficiency falls at part load because friction stays roughly constant.

Question 10 · hard

A rope-brake dynamometer has a 0.6 m drum and a 20 mm rope. At 1,500 rev/min the dead load is 400 N and the spring balance reads 50 N. The brake power is closest to

  1. 16.49 kW
  2. 21.91 kW
  3. 17.04 kW
  4. 2.71 kW
Answer and working

C. 17.04 kW

BP = (W − S)π(D + d)N/60 = 350 × π × 0.62 × 25 = 17043 W = 17.04 kW. Ignoring the rope diameter gives 16.49 kW; adding W and S instead of subtracting gives 21.91 kW. Using T × N/60 without 2π gives 2.71 kW.

A study plan for Tractor & Automotive Engines (IC Engines) in ICAR AIEEA-PG

This plan follows where our questions actually fall, so the time goes where the marks are likely to be. It is our reading of the syllabus, not the exam body's weighting.

  1. First, the heavy units (54% of the 50 questions): Fuel properties (6, 12%); Engine performance: IP, BP, FP and efficiencies (5, 10%); Combustion and knock (4, 8%); Emission norms (4, 8%); Engine classification and terminology (4, 8%); Governing (4, 8%).

    Read the manual chapters for these first and do every worked question you can find on them.

  2. Then the middle band: Two-stroke and four-stroke engines (4, 8%); Engine components (3, 6%); Engine testing (3, 6%); Lubrication system and lubricants (3, 6%); Otto, Diesel and dual cycles (3, 6%); Air intake and turbocharging (2, 4%).

    Aim for one sitting per unit, then mixed questions across them.

  3. Then the lighter units: Ignition and electrical system: battery, starter and alternator (2, 4%); BSFC and heat balance (1, 2%); Cooling system (1, 2%); Diesel fuel system: injection pump and injector (1, 2%).

    Learn the definitions, classifications and standard numbers; these units are more often recalled than worked.

  4. Leave time for the hard ones: Engine performance: IP, BP, FP and efficiencies (2 hard of 5), Engine testing (1 hard of 3), Combustion and knock (1 hard of 4).

    Come back to these after a first pass, untimed, and read every explanation, including for the options you rejected.

  5. Bank the easy marks: BSFC and heat balance (1 easy of 1); Cooling system (1 easy of 1).

    Do these early in revision so they are fast on the day.

  6. Finish timed. Sit the subject as a timed set without notes, mark it, and send each wrong answer back to its unit above.

Last updated · How Laisha writes and checks its pages · Report a mistake

Ask Laisha about this

Opens Laisha's chat with your question ready to send. Sign in or start free.

Unlock every question — ICAR AIEEA-PG Tractor & Automotive Engines (IC Engines)

US$10 a month · one price worldwide · cancel any time

  • Every practice question in this subject, with full working
  • Timed exam papers and progress by unit
  • Ask Laisha to explain any answer — up to 1,000 questions a month
Free or Smarter
FreeSmarter
Grow guides, pest pages, articlesRead allRead all
Ask Laisha5 a dayUp to 1,000 a month
Exam practiceThe sample on each pageEvery question, timed papers
Crop calendar and pest alerts—For your own fields
Calculators and tools—All
Uploads and reports—100 a month, real files
10 days free for every new account, no card.