LAISHA
Open Laisha

ICAR AICE-JRF/SRF Farm Machinery & Equipment II — Plant Protection, Harvesting, Threshing: practice questions

ICAR AICE-JRF/SRF (PhD) — Agricultural Engineering subjects 38–43 · India · National Testing Agency for ICAR

Original practice questions written to the published syllabus · not past papers
10worked here, free
36written to this exam in this subject
14syllabus units

About ICAR AICE-JRF/SRF

ICAR AICE-JRF/SRF (PhD) — Agricultural Engineering subjects 38–43 is a PhD, fellowship and lectureship exam run by National Testing Agency for ICAR, for candidates in India. LAN-based computer test, 2 hours, 120 MCQs: 20 Part A (general knowledge and reasoning), 50 Part B (core group), 50 Part C (specialisation); four options.

Source: icar.org.in.

Checked against the exam body's published information. Formats and fees change; confirm the current edition there before you book.

Farm Machinery & Equipment II — Plant Protection, Harvesting, Threshing in ICAR AICE-JRF/SRF

Design of plant protection and harvesting equipment: droplet spectra and drift, electrostatic and air-assisted spraying, cutting mechanics, threshing and separation theory, loss functions and capacity.

Sprayers, weeders, mowers, reapers, combines and threshers: how they work, how to calibrate them and where losses come from.

Our 36 ICAR AICE-JRF/SRF questions in this subject: 0 easy, 13 medium, 23 hard, across 14 units.

10 practice questions, worked

Choose an answer, then open the working. Each explanation says why the right answer is right and why the others are not.

These 10 were written to ICAR AICE-JRF/SRF and are not shown on any other exam's page.

Question 1 · hard

Why is electrostatic charging of little help deep inside a dense canopy?

  1. Charge collects on outer leaves and shields the interior, so field lines end on the outside
  2. The canopy interior is electrically insulated from earth, so droplets there lose their charge before reaching the leaves
  3. Charged droplets are repelled by wet leaves
  4. Air-assist cannot be used with charged sprays
Answer and working

A. Charge collects on outer leaves and shields the interior, so field lines end on the outside

Outer leaves act as the nearest earthed targets and intercept charged droplets; the field inside the canopy is weak (a Faraday-cage or space-charge effect). Plants are not insulated from earth, and air-assist is often combined with charging to help penetration.

Question 2 · hard

A pulse-width-modulated (PWM) boom is set to halve its flow rate at constant pressure. What happens to droplet size compared with halving flow by lowering pressure on a conventional nozzle?

  1. Both give finer droplets
  2. PWM makes droplets much finer, while pressure reduction keeps droplet size constant at the lower flow
  3. Both keep droplet size constant
  4. PWM keeps droplet size about the same, while lowering pressure makes droplets coarser
Answer and working

D. PWM keeps droplet size about the same, while lowering pressure makes droplets coarser

PWM changes flow through the fraction of time the nozzle is open, at unchanged pressure, so the spectrum is about the same. Cutting flow in half by pressure alone needs pressure at one quarter, which coarsens the spray and may collapse the pattern.

Question 3 · medium

For any real nozzle spray, the number median diameter (NMD) compared with the volume median diameter (VMD) is

  1. larger, because large droplets dominate the count
  2. smaller
  3. equal, for flat-fan nozzles
  4. larger only at high pressure
Answer and working

B. smaller

Small droplets dominate the count but carry little volume, while a few large droplets carry much of it, so NMD < VMD; VMD/NMD equals 1 only for a perfectly uniform spray.

Question 4 · hard

A spray of 200 L/ha is applied as uniform 250 µm droplets on a flat horizontal surface. About how many droplets land per square centimetre?

  1. About 24
  2. About 2,440
  3. About 61
  4. About 244
Answer and working

D. About 244

Volume per cm²: 200 L/ha = 0.2 m³ per 10^8 cm² = 2 × 10^-9 m³/cm². One droplet: (π/6)(250 × 10^-6)³ = 8.18 × 10^-12 m³. Number = 2 × 10^-9 / 8.18 × 10^-12 ≈ 244. Slipping a factor of ten in the hectare conversion gives 24 or 2,440; 61 is a quarter of the correct count and would need droplets about 400 µm across.

Question 5 · hard

On a calm, clear evening a farmer notes that there is no wind and decides it is ideal for spraying a fine insecticide mist next to a sensitive crop. The main risk is

  1. rapid evaporation of the fine droplets from the high afternoon temperature before they land
  2. poor penetration due to leaf movement
  3. a temperature inversion keeping fine droplets suspended and moving them far
  4. nozzle blockage from dew
Answer and working

C. a temperature inversion keeping fine droplets suspended and moving them far

On calm clear evenings the ground cools, cool air lies under warmer air, and vertical mixing stops. Fine droplets stay aloft in a concentrated cloud and drift sideways over long distances. Evaporation is a daytime problem.

Question 6 · hard

A sprayer with a flow-based rate controller increases its speed by 40% on a smooth part of the field. To keep L/ha constant with the same conventional nozzles, nozzle pressure must rise by a factor of about

  1. 1.4
  2. 1.2
  3. 2.8
  4. 2.0
Answer and working

D. 2.0

Flow must rise by 1.4 times; since Q ∝ √P, pressure must rise by 1.4² = 1.96, about double. That also makes the spray finer, which is why conventional nozzles have a limited speed range under rate control. 1.2 takes the square root of 1.4 instead of squaring it; 2.8 doubles 1.4.

Question 7 · hard

Walker (separation) loss in a conventional combine increases with MOG feed rate approximately

  1. linearly, in direct proportion
  2. exponentially, rising sharply beyond a certain feed rate
  3. not at all
  4. inversely
Answer and working

B. exponentially, rising sharply beyond a certain feed rate

A thicker straw mat traps more free grain, and the fraction carried out rises steeply as feed rate grows. This curve sets the capacity at an acceptable loss level.

Question 8 · medium

The main function of the oscillating grain pan below the cylinder is to

  1. convey material to the sieves and stratify it so grain lies under the chaff
  2. thresh remaining heads
  3. separate long straw from grain by tossing it rearward over a series of stepped risers
  4. elevate grain to the tank
Answer and working

A. convey material to the sieves and stratify it so grain lies under the chaff

Oscillation moves material rearward and lets heavy grain sink below lighter chaff, so when it reaches the chaffer the grain is already in contact with the sieve.

Question 9 · hard

A 1 m² frame placed behind a combine collects 36 free grains and 4 unthreshed heads averaging 25 grains each. TGW is 45 g. The total machine loss (assuming no header or pre-harvest loss) is

  1. 16.2 kg/ha
  2. 45.0 kg/ha
  3. 6.1 kg/ha
  4. 61.2 kg/ha
Answer and working

D. 61.2 kg/ha

Total grains = 36 + 4 × 25 = 136 per m². Loss = 136 × 45/100 = 61.2 kg/ha. Counting only free grain gives 36 × 45/100 = 16.2 kg/ha; a unit slip gives 6.1.

Question 10 · medium

The main environmental reason for developing in-situ rice straw management machines in north-west India was to

  1. reduce groundwater extraction
  2. increase straw export
  3. reduce air pollution from burning straw
  4. reduce fertiliser use
Answer and working

C. reduce air pollution from burning straw

Burning to clear fields for wheat causes severe seasonal air pollution; machines that manage straw without burning were developed and promoted for that reason.

A study plan for Farm Machinery & Equipment II — Plant Protection, Harvesting, Threshing in ICAR AICE-JRF/SRF

This plan follows where our questions actually fall, so the time goes where the marks are likely to be. It is our reading of the syllabus, not the exam body's weighting.

  1. First, the heavy units (50% of the 36 questions): Mowers: reciprocating and rotary; mechanics of cutting (4, 11%); Nozzles and droplet spectra (4, 11%); Sprayers: hydraulic, air-assisted and electrostatic (4, 11%); Combine harvester: header, threshing cylinder and concave (3, 8%); Combine separation and cleaning: straw walker and cleaning shoe (3, 8%).

    Read the manual chapters for these first and do every worked question you can find on them.

  2. Then the middle band: Cotton and sugarcane harvesting (3, 8%); Harvesting and threshing losses (3, 8%); Reapers (2, 6%); Root-crop diggers (2, 6%); Sprayer calibration and application rate (2, 6%).

    Aim for one sitting per unit, then mixed questions across them.

  3. Then the lighter units: Straw and residue management machines (2, 6%); Weeders and inter-cultivation equipment (2, 6%); Chaff cutters (1, 3%); Threshers (1, 3%).

    Learn the definitions, classifications and standard numbers; these units are more often recalled than worked.

  4. Leave time for the hard ones: Harvesting and threshing losses (3 hard of 3), Sprayer calibration and application rate (2 hard of 2), Chaff cutters (1 hard of 1).

    Come back to these after a first pass, untimed, and read every explanation, including for the options you rejected.

  5. Finish timed. Sit the subject as a timed set without notes, mark it, and send each wrong answer back to its unit above.

Last updated · How Laisha writes and checks its pages · Report a mistake

Ask Laisha about this

Opens Laisha's chat with your question ready to send. Sign in or start free.

Unlock every question — ICAR AICE-JRF/SRF Farm Machinery & Equipment II — Plant Protection, Harvesting, Threshing

US$10 a month · one price worldwide · cancel any time

  • Every practice question in this subject, with full working
  • Timed exam papers and progress by unit
  • Ask Laisha to explain any answer — up to 1,000 questions a month
Free or Smarter
FreeSmarter
Grow guides, pest pages, articlesRead allRead all
Ask Laisha5 a dayUp to 1,000 a month
Exam practiceThe sample on each pageEvery question, timed papers
Crop calendar and pest alerts—For your own fields
Calculators and tools—All
Uploads and reports—100 a month, real files
10 days free for every new account, no card.