LAISHA
Open Laisha

NDDB and dairy cooperative recruitment Engineering Fundamentals for Dairy Technologists: practice questions

NDDB and dairy cooperative recruitment · India · National Dairy Development Board; state cooperative milk federations

Original practice questions written to the published syllabus · not past papers
10worked here, free
27written to this exam in this subject
8syllabus units

About NDDB and dairy cooperative recruitment

NDDB and dairy cooperative recruitment is a professional certification run by National Dairy Development Board; state cooperative milk federations, for candidates in India. NDDB's career page links to an external portal; no selection procedure was shown when read on 3 Oct 2026.

Official site: nddb.coop.

We have not been able to confirm these details against the exam body's own specification, so fees, dates and pass marks are left out on purpose. Check the current format, eligibility, fees and dates on the official site.

Engineering Fundamentals for Dairy Technologists in NDDB and dairy cooperative recruitment

Drawing, workshop, mechanics, materials and electricity as used in a milk plant. Go to the agricultural engineering track (engineering-drawing-cad, workshop-technology, basic-electrical-electronics) for depth.

Our 27 NDDB and dairy cooperative recruitment questions in this subject: 2 easy, 25 medium, 0 hard, across 8 units.

10 practice questions, worked

Choose an answer, then open the working. Each explanation says why the right answer is right and why the others are not.

These 10 were written to NDDB and dairy cooperative recruitment and are not shown on any other exam's page.

Question 1 · medium

Hygienic-design guidance commonly specifies product-contact surfaces with a roughness of:

  1. Ra at least 3.2 µm, to grip the product film
  2. Ra no more than 0.8 µm
  3. Ra of 12.5 µm as cast
  4. Any roughness, if a cleaning chemical is used
Answer and working

B. Ra no more than 0.8 µm

Smooth surfaces of Ra ≤ 0.8 µm resist bacterial attachment and clean more easily. Rougher surfaces harbour soil and organisms.

Question 2 · easy

Stainless-steel dairy pipework is normally welded by:

  1. TIG welding with argon shielding
  2. Oxy-acetylene gas welding
  3. Soft soldering with tin–lead
  4. Brazing with brass filler rod
Answer and working

A. TIG welding with argon shielding

Gas tungsten arc (TIG) welding, often orbital, gives clean, fully penetrated welds. Solder and brass are unacceptable for product contact.

Question 3 · medium

For welded tanks and pipework handling salted whey, the best common choice among these grades is:

  1. 304
  2. 316L
  3. 430
  4. 420
Answer and working

B. 316L

316L combines molybdenum for chloride resistance with low carbon to avoid sensitisation at welds. 430 is ferritic; 420 is a martensitic cutlery grade.

Question 4 · medium

Using PREN = %Cr + 3.3 %Mo + 16 %N, what is the PREN of a steel with 17% Cr, 2.5% Mo and 0.05% N?

  1. 26.1
  2. 19.6
  3. 25.2
  4. 57.0
Answer and working

A. 26.1

PREN = 17 + 3.3 × 2.5 + 16 × 0.05 = 17 + 8.25 + 0.8 = 26.1. Ignoring nitrogen gives 25.25.

Question 5 · medium

A centrifugal milk pump repeatedly destroys its mechanical seal and bearings within weeks. The first thing to check is:

  1. The fat content and temperature of the milk being pumped
  2. Alignment of the motor and pump shafts at the coupling
  3. The colour of the pump casing paint
  4. The tooth count of the motor's cooling fan
Answer and working

B. Alignment of the motor and pump shafts at the coupling

Misalignment is the commonest cause of coupling, bearing and seal failures; it is checked with dial indicators or laser tools.

Question 6 · medium

The main purpose of earthing the metal frame of a motor is to:

  1. Reduce the motor's running current and so its energy use
  2. Increase the supply voltage to the motor terminals at start
  3. Let fault current flow so the protective device trips fast
  4. Prevent the motor from overheating
Answer and working

C. Let fault current flow so the protective device trips fast

A low-impedance earth path ensures an insulation fault draws enough current to trip the fuse or breaker.

Question 7 · medium

Why is the electrical shock risk higher in a dairy processing hall than in an office?

  1. Wet skin and floors lower body resistance
  2. Dairy equipment runs on direct current only
  3. Milk is a perfect electrical insulator
  4. Stainless steel cannot be earthed
Answer and working

A. Wet skin and floors lower body resistance

Water lowers contact resistance, raising current for a given voltage; conductive metal surrounds the worker.

Question 8 · medium

Equipotential bonding of tanks, pipes and platforms in a wet dairy area is done to:

  1. Reduce the electricity bill
  2. Keep touchable metal parts at the same potential
  3. Increase motor efficiency
  4. Protect the stainless steel from chloride pitting in brine
Answer and working

B. Keep touchable metal parts at the same potential

Bonding keeps simultaneously accessible metal at the same potential during a fault.

Question 9 · medium

A filler has a mean time between failures of 95 h and a mean time to repair of 5 h. What is its inherent availability?

  1. 90%
  2. 95%
  3. 105%
  4. 5%
Answer and working

B. 95%

A = MTBF/(MTBF + MTTR) = 95/100 = 95%.

Question 10 · medium

After maintenance work on a filler in a product area, production should restart only when:

  1. The maintenance technician alone has signed off the electrical and mechanical work
  2. The first ten packs have been discarded, whatever their condition
  3. The machine has run empty for one hour
  4. Tools are accounted for and quality staff release the cleaned machine
Answer and working

D. Tools are accounted for and quality staff release the cleaned machine

Maintenance is a food-safety activity: tool and part control, removal of debris, cleaning and formal hygiene release prevent foreign bodies and contamination.

A study plan for Engineering Fundamentals for Dairy Technologists in NDDB and dairy cooperative recruitment

This plan follows where our questions actually fall, so the time goes where the marks are likely to be. It is our reading of the syllabus, not the exam body's weighting.

  1. First, the heavy units (59% of the 27 questions): Electrical safety and earthing (6, 22%); Lubrication and maintenance of machines (6, 22%); Corrosion and its control in dairy plants (4, 15%).

    Read the manual chapters for these first and do every worked question you can find on them.

  2. Then the middle band: Engineering drawing and reading plant drawings (3, 11%); Workshop practice: fitting, welding and sheet-metal work (3, 11%); Electric motors and starters in dairy plants (2, 7%).

    Aim for one sitting per unit, then mixed questions across them.

  3. Then the lighter units: Stainless steels and other dairy plant materials (2, 7%); Power transmission: belts, gears and couplings (1, 4%).

    Learn the definitions, classifications and standard numbers; these units are more often recalled than worked.

  4. Bank the easy marks: Workshop practice: fitting, welding and sheet-metal work (1 easy of 3); Electrical safety and earthing (1 easy of 6).

    Do these early in revision so they are fast on the day.

  5. Finish timed. Sit the subject as a timed set without notes, mark it, and send each wrong answer back to its unit above.

Last updated · How Laisha writes and checks its pages · Report a mistake

Ask Laisha about this

Opens Laisha's chat with your question ready to send. Sign in or start free.

Unlock every question — NDDB and dairy cooperative recruitment Engineering Fundamentals for Dairy Technologists

US$10 a month · one price worldwide · cancel any time

  • Every practice question in this subject, with full working
  • Timed exam papers and progress by unit
  • Ask Laisha to explain any answer — up to 1,000 questions a month
Free or Smarter
FreeSmarter
Grow guides, pest pages, articlesRead allRead all
Ask Laisha5 a dayUp to 1,000 a month
Exam practiceThe sample on each pageEvery question, timed papers
Crop calendar and pest alerts—For your own fields
Calculators and tools—All
Uploads and reports—100 a month, real files
10 days free for every new account, no card.