LAISHA
Open Laisha

ICAR AIEEA-PG Engineering Fundamentals for Dairy Technologists: practice questions

ICAR AIEEA-PG: Dairy Science (group 16) and Dairy Technology (group 17) · India · NTA for ICAR

Original practice questions written to the published syllabus · not past papers
10worked here, free
83written to this exam in this subject
10syllabus units

About ICAR AIEEA-PG

ICAR AIEEA-PG: Dairy Science (group 16) and Dairy Technology (group 17) is a postgraduate admission exam run by NTA for ICAR, for candidates in India. Computer-based, 2 hours, 120 multiple-choice questions, +4 for a correct answer and −1 for a wrong one (2026 bulletin). One paper per major subject group.

Source: icar.org.in.

Checked against the exam body's published information. Formats and fees change; confirm the current edition there before you book.

Engineering Fundamentals for Dairy Technologists in ICAR AIEEA-PG

Drawing, workshop, mechanics, materials and electricity as used in a milk plant. Go to the agricultural engineering track (engineering-drawing-cad, workshop-technology, basic-electrical-electronics) for depth.

Our 83 ICAR AIEEA-PG questions in this subject: 12 easy, 68 medium, 3 hard, across 10 units.

10 practice questions, worked

Choose an answer, then open the working. Each explanation says why the right answer is right and why the others are not.

These 10 were written to ICAR AIEEA-PG and are not shown on any other exam's page.

Question 1 · easy

In first-angle orthographic projection, where is the plan (top view) placed relative to the front elevation?

  1. Above it
  2. To its left
  3. Superimposed on it
  4. Below it
Answer and working

D. Below it

First-angle projection puts the plan below the elevation; third-angle, used mainly in North America, puts it above.

Question 2 · medium

Which method develops the flat pattern of a square-to-round transition piece for a hopper outlet?

  1. Triangulation
  2. Parallel-line development
  3. Radial-line development
  4. Orthographic projection alone
Answer and working

A. Triangulation

Transition pieces are developed by triangulation. Parallel-line development suits prisms and cylinders; radial-line suits cones and pyramids.

Question 3 · medium

Small, deep holes perforate a stainless tank wall while the surrounding surface looks bright. The tank held brine. The corrosion form is:

  1. Uniform corrosion
  2. Erosion–corrosion
  3. Pitting
  4. Galvanic corrosion
Answer and working

C. Pitting

Chloride pitting is localised and deep with little general attack.

Question 4 · medium

Sensitisation of ordinary-carbon austenitic stainless steel occurs when it is held in the range of about:

  1. 50–150 °C
  2. 1,050–1,150 °C
  3. 450–850 °C
  4. −20 to 0 °C
Answer and working

C. 450–850 °C

Chromium carbides precipitate at grain boundaries between about 450 and 850 °C, as in weld heat-affected zones. 1,050–1,150 °C is the solution-annealing range that dissolves them.

Question 5 · medium

In a star-connected three-phase system with 400 V between lines, the voltage from each line to neutral is about:

  1. 230 V
  2. 400 V
  3. 693 V
  4. 133 V
Answer and working

A. 230 V

V_ph = V_L/√3 = 400/1.732 ≈ 231 V. Multiplying by √3 gives 693 V.

Question 6 · medium

An undersized cable feeding a distant pump motor will mainly cause:

  1. Voltage drop and cable heating, so the motor runs hot and weak
  2. Higher motor speed and lower current because resistance limits load
  3. A rise in supply frequency at the motor
  4. No effect, because current is the same everywhere
Answer and working

A. Voltage drop and cable heating, so the motor runs hot and weak

R = ρL/A: a small area and long length give high resistance, I²R heating and voltage drop.

Question 7 · medium

A 4-pole, 50 Hz induction motor runs at 1,455 rpm. What is its slip?

  1. 4.5%
  2. 3%
  3. 0.3%
  4. 97%
Answer and working

B. 3%

s = (1,500 − 1,455)/1,500 = 45/1,500 = 0.03 = 3%.

Question 8 · medium

With a star–delta starter, the starting current and starting torque compared with direct-on-line starting are:

  1. Both reduced to one half
  2. Current reduced by √3, torque unchanged
  3. Both reduced to one third
  4. Both increased by √3
Answer and working

C. Both reduced to one third

In star each winding receives V/√3, so phase current falls by √3 and line current and torque by 3.

Question 9 · medium

An induction motor started direct-on-line typically draws a starting current of about:

  1. 5–8 times full-load current
  2. Equal to full-load current
  3. Half of full-load current
  4. 50 times full-load current
Answer and working

A. 5–8 times full-load current

Locked-rotor current is typically 5–8 times rated current for a few seconds.

Question 10 · medium

In total productive maintenance, 'autonomous maintenance' means:

  1. Machines repair themselves using built-in sensors
  2. Contractors take over all routine and breakdown maintenance work
  3. Maintenance is done only when a machine stops
  4. Operators do routine cleaning, inspection and lubrication
Answer and working

D. Operators do routine cleaning, inspection and lubrication

Operators take ownership of basic care so that small defects are found early, freeing technicians for skilled work.

A study plan for Engineering Fundamentals for Dairy Technologists in ICAR AIEEA-PG

This plan follows where our questions actually fall, so the time goes where the marks are likely to be. It is our reading of the syllabus, not the exam body's weighting.

  1. First, the heavy units (46% of the 83 questions): Electric motors and starters in dairy plants (10, 12%); Statics, friction and strength of materials basics (10, 12%); Lubrication and maintenance of machines (9, 11%); Power transmission: belts, gears and couplings (9, 11%).

    Read the manual chapters for these first and do every worked question you can find on them.

  2. Then the middle band: Corrosion and its control in dairy plants (8, 10%); DC and AC circuits, three-phase supply (8, 10%); Workshop practice: fitting, welding and sheet-metal work (8, 10%); Electrical safety and earthing (7, 8%).

    Aim for one sitting per unit, then mixed questions across them.

  3. Then the lighter units: Engineering drawing and reading plant drawings (7, 8%); Stainless steels and other dairy plant materials (7, 8%).

    Learn the definitions, classifications and standard numbers; these units are more often recalled than worked.

  4. Leave time for the hard ones: Statics, friction and strength of materials basics (2 hard of 10), Electric motors and starters in dairy plants (1 hard of 10).

    Come back to these after a first pass, untimed, and read every explanation, including for the options you rejected.

  5. Bank the easy marks: Engineering drawing and reading plant drawings (2 easy of 7); Power transmission: belts, gears and couplings (2 easy of 9).

    Do these early in revision so they are fast on the day.

  6. Finish timed. Sit the subject as a timed set without notes, mark it, and send each wrong answer back to its unit above.

Last updated · How Laisha writes and checks its pages · Report a mistake

Ask Laisha about this

Opens Laisha's chat with your question ready to send. Sign in or start free.

Unlock every question — ICAR AIEEA-PG Engineering Fundamentals for Dairy Technologists

US$10 a month · one price worldwide · cancel any time

  • Every practice question in this subject, with full working
  • Timed exam papers and progress by unit
  • Ask Laisha to explain any answer — up to 1,000 questions a month
Free or Smarter
FreeSmarter
Grow guides, pest pages, articlesRead allRead all
Ask Laisha5 a dayUp to 1,000 a month
Exam practiceThe sample on each pageEvery question, timed papers
Crop calendar and pest alerts—For your own fields
Calculators and tools—All
Uploads and reports—100 a month, real files
10 days free for every new account, no card.