NCEES FE Environmental Air & Noise Pollution: Monitoring & Control: practice questions
NCEES FE Environmental · USA · National Council of Examiners for Engineering and Surveying
Original practice questions written to the published syllabus · not past papers
10worked here, free
43written to this exam in this subject
10syllabus units
About NCEES FE Environmental
NCEES FE Environmental is a licensing and registration exam run by National Council of Examiners for Engineering and Surveying, for candidates in USA. Computer-based at Pearson VUE, 110 questions, 6-hour appointment (5 h 20 min exam time, 25-minute break). Reference handbook supplied on screen.
Checked against the exam body's published information. Formats and fees change; confirm the current edition there before you book.
Air & Noise Pollution: Monitoring & Control in NCEES FE Environmental
Air quality engineering calculations: dispersion, control device efficiency, combustion and emission estimates, and noise.
Air pollutants, their health and crop effects, standards and indices, dispersion, and control equipment, plus noise. Agricultural sources (residue burning, ammonia, dust, odour) are covered here alongside the industrial ones GATE ES examines.
Our 43 NCEES FE Environmental questions in this subject: 6 easy, 24 medium, 13 hard, across 10 units.
10 practice questions, worked
Choose an answer, then open the working. Each explanation says why the right answer is right and why the others are not.
These 10 were written to NCEES FE Environmental and are not shown on any other exam's page.
Question 1 · easy
A room of 200 m³ receives 1000 m³ of outdoor air per hour. How many air changes per hour (ACH) is this?
5
1200
200
0.2
Answer and working
A. 5
ACH = 1000/200 = 5. 0.2 inverts the ratio; 200 is the volume; 1200 adds.
Question 2 · medium
For a ground-level source (H = 0) with Q = 100 g/s, u = 5 m/s, σy = 100 m and σz = 50 m, what is the centreline ground-level concentration?
A study plan for Air & Noise Pollution: Monitoring & Control in NCEES FE Environmental
This plan follows where our questions actually fall, so the time goes where the marks are likely to be. It is our reading of the syllabus, not the exam body's weighting.
First, the heavy units (63% of the 43 questions): Particulate control: settling chambers, cyclones, wet scrubbers, fabric filters, ESP (8, 19%); Gaussian plume dispersion modelling (7, 16%); Gaseous control: absorption, adsorption, condensation, combustion (6, 14%); Noise: sources, effects, standards, measurement and control (6, 14%).
Read the manual chapters for these first and do every worked question you can find on them.
Then the middle band: Control of SOx, NOx, CO and hydrocarbons; vehicle emissions (5, 12%); Meteorology and dispersion: stability, mixing height, wind rose (4, 9%); Emission inventories for point, line and area sources (3, 7%); Indoor air pollution (2, 5%).
Aim for one sitting per unit, then mixed questions across them.
Then the lighter units: Air quality indices and visibility (1, 2%); Criteria pollutants, ambient and emission standards (1, 2%).
Learn the definitions, classifications and standard numbers; these units are more often recalled than worked.
Leave time for the hard ones: Indoor air pollution (1 hard of 2), Gaussian plume dispersion modelling (3 hard of 7), Control of SOx, NOx, CO and hydrocarbons; vehicle emissions (2 hard of 5).
Come back to these after a first pass, untimed, and read every explanation, including for the options you rejected.
Bank the easy marks: Indoor air pollution (1 easy of 2); Emission inventories for point, line and area sources (1 easy of 3).
Do these early in revision so they are fast on the day.
Finish timed. Sit the subject as a timed set without notes, mark it, and send each wrong answer back to its unit above.