State dairy development department posts Dairy Plant Utilities & Energy Management: practice questions
State dairy development department posts · India · State public service commissions (e.g. Kerala PSC)
Original practice questions written to the published syllabus · not past papers
10worked here, free
58written to this exam in this subject
10syllabus units
About State dairy development department posts
State dairy development department posts is a government recruitment exam run by State public service commissions (e.g. Kerala PSC), for candidates in India.
We have not been able to confirm these details against the exam body's own specification, so fees, dates and pass marks are left out on purpose. Check the current format, eligibility, fees and dates on the official site.
Dairy Plant Utilities & Energy Management in State dairy development department posts
Steam, water, compressed air and electricity in the milk plant, and how to audit and cut energy and water use.
Our 58 State dairy development department posts questions in this subject: 26 easy, 28 medium, 4 hard, across 10 units.
10 practice questions, worked
Choose an answer, then open the working. Each explanation says why the right answer is right and why the others are not.
These 10 were written to State dairy development department posts and are not shown on any other exam's page.
Question 1 · medium
Leaks take 5 kW of compressor power, 8,000 hours a year, with electricity at 8 currency units per kWh. What do they cost each year?
40,000 currency units
32,000 currency units
64,000 currency units
320,000 currency units
Answer and working
D. 320,000 currency units
5 × 8,000 = 40,000 kWh; × 8 currency units = 320,000. 40,000 currency units forgets the price; the others misplace a factor.
Question 2 · easy
Why do most dairies install two or more boilers?
Because boiler law in most countries bans single-boiler plants
One stays online while another is serviced
To avoid water treatment
To double steam pressure
Answer and working
B. One stays online while another is serviced
Redundancy allows inspection and repair without stopping production and avoids running one boiler at very low load.
Question 3 · medium
Which trap type is usually preferred for a heat exchanger with a modulating steam supply?
Float-and-thermostatic
Bimetallic thermostatic trap set for subcooling
An open drain pipe
Thermodynamic disc
Answer and working
A. Float-and-thermostatic
Float traps discharge condensate continuously at steam temperature and vent air, suiting modulating loads.
Question 4 · easy
Why are steam mains and fittings insulated?
To remove air from the steam space
To make cleaning easier
Less heat loss
To increase steam pressure
Answer and working
C. Less heat loss
Bare pipes lose heat continuously, wasting fuel and adding condensate.
Question 5 · medium
What is the purpose of a backflow preventer or air gap on a water supply?
Increasing water pressure
Softening water
Stopping back-flow into potable lines
Measuring flow to each department for water billing purposes
Answer and working
C. Stopping back-flow into potable lines
Back-siphonage or back-pressure could otherwise pull process or chemical solutions into potable water.
Question 6 · easy
What is a main role of an air receiver?
Drying air below freezing
Making air oil-free for food contact
Buffering demand
Raising pressure above the compressor setting
Answer and working
C. Buffering demand
Receivers store air to smooth demand and let water settle for draining.
Question 7 · medium
How is a low power factor usually corrected?
Capacitor banks
Larger cables
Raising the supply voltage
Adding motors
Answer and working
A. Capacitor banks
Capacitors supply reactive power locally, cutting kVA drawn from the grid.
Question 8 · medium
What are IE3 and IE4?
Boiler pressure classes
Insulation classes for cables
Air purity grades
Motor efficiency classes
Answer and working
D. Motor efficiency classes
International efficiency classes for motors; higher numbers mean higher efficiency.
Question 9 · medium
In a liquid milk plant, which is often the largest electrical user?
Gate barriers
Office lighting and computers
Packing machine heaters
Refrigeration
Answer and working
D. Refrigeration
Refrigeration for chilling and cold storage commonly leads electrical use.
Question 10 · medium
How is solar thermal heat usually integrated into dairy heating?
Preheating water, with storage
Driving air compressors
Replacing the boiler entirely in all seasons
Superheating steam
Answer and working
A. Preheating water, with storage
Variable solar supply is buffered in storage and topped up by conventional heat.
A study plan for Dairy Plant Utilities & Energy Management in State dairy development department posts
This plan follows where our questions actually fall, so the time goes where the marks are likely to be. It is our reading of the syllabus, not the exam body's weighting.
First, the heavy units (48% of the 58 questions): Water conservation and reuse (8, 14%); Electrical supply and power factor (7, 12%); Energy audits (7, 12%); Boiler and pressure-vessel safety rules (6, 10%).
Read the manual chapters for these first and do every worked question you can find on them.
Then the middle band: Boilers: types, fittings, mountings and efficiency (6, 10%); Compressed air systems (6, 10%); Water supply, treatment and quality for dairy use (6, 10%); Renewable energy in dairy plants: solar thermal, biogas (5, 9%).
Aim for one sitting per unit, then mixed questions across them.
Then the lighter units: Steam distribution and condensate recovery (4, 7%); Heat recovery and cogeneration (3, 5%).
Learn the definitions, classifications and standard numbers; these units are more often recalled than worked.
Leave time for the hard ones: Boiler and pressure-vessel safety rules (1 hard of 6), Electrical supply and power factor (1 hard of 7), Energy audits (1 hard of 7).
Come back to these after a first pass, untimed, and read every explanation, including for the options you rejected.
Bank the easy marks: Boilers: types, fittings, mountings and efficiency (4 easy of 6); Boiler and pressure-vessel safety rules (3 easy of 6).
Do these early in revision so they are fast on the day.
Finish timed. Sit the subject as a timed set without notes, mark it, and send each wrong answer back to its unit above.