LAISHA
Open Laisha

SAF Certified Forester Stand Tending, Thinning & Pruning: practice questions

SAF Certified Forester (CF) · USA · Society of American Foresters

Original practice questions written to the published syllabus · not past papers
10worked here, free
20written to this exam in this subject
10syllabus units

About SAF Certified Forester

SAF Certified Forester (CF) is a professional certification run by Society of American Foresters, for candidates in USA. Eligibility by education and experience (details in the SAF Certification Handbook), then the CF exam written to a published domain and knowledge-area outline. Recertification every three years with 45 continuing forestry education hours (at least 30 in Category 1-CF).

Source: eforester.org.

Checked against the exam body's published information. Formats and fees change; confirm the current edition there before you book.

Stand Tending, Thinning & Pruning in SAF Certified Forester

Intermediate treatments: release, precommercial and commercial thinning, low, crown, selection and crop-tree thinning, stand density index and density management, pruning for clear wood, and fertilisation response and economics.

The intermediate treatments between regeneration and harvest that shape a stand's growth, quality and health.

Our 20 SAF Certified Forester questions in this subject: 4 easy, 10 medium, 6 hard, across 10 units.

10 practice questions, worked

Choose an answer, then open the working. Each explanation says why the right answer is right and why the others are not.

These 10 were written to SAF Certified Forester and are not shown on any other exam's page.

Question 1 · medium

In reduced-impact logging, why are climbers cut on trees to be felled, ideally six months or more before felling?

  1. Climber cutting increases the volume of the felled tree by about half before harvest in most tropical species
  2. Climbers must be sold separately before the logging concession can be granted
  3. Cutting climbers turns the tree's heartwood darker, raising its market value
  4. Dead climbers no longer bind crowns together, so felling damages fewer neighbours and is safer
Answer and working

D. Dead climbers no longer bind crowns together, so felling damages fewer neighbours and is safer

Climbers tie crowns together; a felled tree drags neighbours down and endangers workers. Cutting them well ahead lets them die and weaken. The other reasons are invented.

Question 2 · hard

A plantation has 1,111 trees/ha on a square spacing and a top height of 15 m. What is its relative spacing (Hart-Becking index)?

  1. 3 per cent
  2. 20 per cent
  3. 500 per cent
  4. 0.2 per cent
Answer and working

B. 20 per cent

Spacing = √(10,000 ÷ 1,111) = 3.0 m; relative spacing = 3 ÷ 15 × 100 = 20%. 500% divides top height by spacing (15 ÷ 3 × 100); 0.2% forgets to multiply by 100; 3% is the spacing alone.

Question 3 · easy

Reineke's stand density index rests on the observation that in fully stocked stands, log trees per hectare declines with log quadratic mean diameter with a slope of about:

  1. −1.605
  2. −0.5
  3. −3/2
  4. +1.605
Answer and working

A. −1.605

Reineke found a slope of about −1.605 between log N and log Dq. −3/2 is Yoda's self-thinning slope for mean plant mass against density, not diameter; a positive slope would mean more trees as they grow larger.

Question 4 · hard

Why is mechanical thinning often used for first thinnings in plantations?

  1. Trees are still fairly uniform, produce has little value, and machines need access racks
  2. It selects the best trees more accurately than any other thinning method
  3. It is the only method that can be applied to conifer plantations by law
  4. It removes only the dominant trees, which are the most valuable at that age in most plantations
Answer and working

A. Trees are still fairly uniform, produce has little value, and machines need access racks

Uniform young stands, low-value produce and the need for racks favour simple row or spacing thinning. It does not select the best trees, is not legally required, and does not target dominants.

Question 5 · medium

Under British management tables, the marginal thinning intensity is set at 70 per cent of yield class per year. What is it for yield class 14?

  1. 9.8 m³/ha/yr
  2. 14 m³/ha/yr
  3. 4.2 m³/ha/yr
  4. 20 m³/ha/yr
Answer and working

A. 9.8 m³/ha/yr

MTI = 0.7 × 14 = 9.8 m³/ha/yr. 14 is the yield class itself; 4.2 is 30% of it; 20 divides 14 by 0.7.

Question 6 · hard

A stand of yield class 14 is thinned at the marginal thinning intensity (70 per cent of yield class per year) on a five-year cycle. About how much volume is removed at each thinning?

  1. 9.8 m³/ha
  2. 70 m³/ha
  3. 98 m³/ha
  4. 49 m³/ha
Answer and working

D. 49 m³/ha

MTI = 0.7 × 14 = 9.8 m³/ha/yr; over five years 9.8 × 5 = 49 m³/ha. 9.8 is the annual figure; 70 uses the yield class × 5; 98 uses a ten-year cycle.

Question 7 · easy

Which measure is commonly used outside India to express thinning intensity numerically?

  1. Residual basal area, SDI or trees per hectare after thinning
  2. Crown class letters A to D
  3. The colour of paint used for marking
  4. The number of thinnings in the rotation recorded in the plantation journal
Answer and working

A. Residual basal area, SDI or trees per hectare after thinning

Numerical targets such as residual basal area, SDI or stems per hectare are common. Crown-class grades are the Indian system; paint colour and number of thinnings do not express intensity.

Question 8 · hard

A pruned log is 50 cm in diameter and its defect (knotty) core is 20 cm in diameter. What share of the cross-section area is clear wood?

  1. 84 per cent
  2. 60 per cent
  3. 40 per cent
  4. 16 per cent
Answer and working

A. 84 per cent

Clear share = 1 − (20 ÷ 50)² = 1 − 0.16 = 0.84. 60% uses a linear ratio (1 − 0.4); 16% is the core share; 40% is the diameter ratio.

Question 9 · easy

In North American terminology, the three kinds of release treatment are:

  1. Pruning, girdling and fertilisation
  2. Thinning, coppicing and pollarding
  3. Weeding, cleaning and liberation
  4. Salvage, sanitation and selection
Answer and working

C. Weeding, cleaning and liberation

Release frees a young crop from competing herbs and shrubs (weeding), same-age competitors (cleaning) and older overtopping trees (liberation).

Question 10 · medium

How much urea (46 per cent N) supplies 150 kg of nitrogen per hectare?

  1. 326 kg/ha
  2. 69 kg/ha
  3. 150 kg/ha
  4. 196 kg/ha
Answer and working

A. 326 kg/ha

Product = 150 ÷ 0.46 = 326 kg urea. 69 multiplies by 0.46; 150 confuses nutrient with product; 196 adds 46.

A study plan for Stand Tending, Thinning & Pruning in SAF Certified Forester

This plan follows where our questions actually fall, so the time goes where the marks are likely to be. It is our reading of the syllabus, not the exam body's weighting.

  1. First, the heavy units (60% of the 20 questions): Fertilisation of established stands (3, 15%); Release treatments and competition control (3, 15%); Thinning grades and thinning schedules (3, 15%); Thinning: objectives and effects on growth (3, 15%).

    Read the manual chapters for these first and do every worked question you can find on them.

  2. Then the middle band: Pruning: natural and artificial; timing and lift (2, 10%); Thinning methods: mechanical, ordinary (low), crown, selection (2, 10%); Climber cutting (1, 5%); Girdling and other stand-improvement methods (1, 5%).

    Aim for one sitting per unit, then mixed questions across them.

  3. Then the lighter units: Improvement felling and salvage cutting (1, 5%); Weeding and cleaning (1, 5%).

    Learn the definitions, classifications and standard numbers; these units are more often recalled than worked.

  4. Leave time for the hard ones: Pruning: natural and artificial; timing and lift (2 hard of 2), Thinning methods: mechanical, ordinary (low), crown, selection (1 hard of 2), Release treatments and competition control (1 hard of 3).

    Come back to these after a first pass, untimed, and read every explanation, including for the options you rejected.

  5. Bank the easy marks: Girdling and other stand-improvement methods (1 easy of 1); Release treatments and competition control (1 easy of 3).

    Do these early in revision so they are fast on the day.

  6. Finish timed. Sit the subject as a timed set without notes, mark it, and send each wrong answer back to its unit above.

Last updated · How Laisha writes and checks its pages · Report a mistake

Ask Laisha about this

Opens Laisha's chat with your question ready to send. Sign in or start free.

Unlock every question — SAF Certified Forester Stand Tending, Thinning & Pruning

US$10 a month · one price worldwide · cancel any time

  • Every practice question in this subject, with full working
  • Timed exam papers and progress by unit
  • Ask Laisha to explain any answer — up to 1,000 questions a month
Free or Smarter
FreeSmarter
Grow guides, pest pages, articlesRead allRead all
Ask Laisha5 a dayUp to 1,000 a month
Exam practiceThe sample on each pageEvery question, timed papers
Crop calendar and pest alerts—For your own fields
Calculators and tools—All
Uploads and reports—100 a month, real files
10 days free for every new account, no card.