GATE XL Cereal Science & Milling Technology: practice questions
GATE — Life Sciences (XL), Section U Food Technology · India · IITs and IISc on rotation (2027: IIT Madras)
Original practice questions written to the published syllabus · not past papers
10worked here, free
38written to this exam in this subject
12syllabus units
About GATE XL
GATE — Life Sciences (XL), Section U Food Technology is a postgraduate admission exam run by IITs and IISc on rotation (2027: IIT Madras), for candidates in India. Computer-based, 3 hours, 100 marks. MCQ, MSQ and NAT. Within XL, Section P Chemistry is understood to be compulsory and the candidate chooses two further sections, of which U Food Technology is one; this structure and the mark split are from earlier brochures and were not re-read for 2026.
Checked against the exam body's published information. Formats and fees change; confirm the current edition there before you book.
Cereal Science & Milling Technology in GATE XL
Same Section 3 content as XE-G, with more emphasis on grain chemistry: gluten proteins, amylose and rice quality, β-glucan, starch modification.
The structure and chemistry of cereal grains and millets and how they are milled into flour, semolina, rice and maize products, with the flour quality tests that decide what each flour can make.
Our 38 GATE XL questions in this subject: 16 easy, 16 medium, 6 hard, across 12 units.
10 practice questions, worked
Choose an answer, then open the working. Each explanation says why the right answer is right and why the others are not.
These 10 were written to GATE XL and are not shown on any other exam's page.
Question 1 · medium
In a wheat flour mill, the break system uses:
Smooth rolls running at equal speeds
Hammer mills with fine screens
Corrugated rolls at differential speed
Stone discs rotating in opposite directions
Answer and working
C. Corrugated rolls at differential speed
Fluted rolls at differential speed open the kernel and scrape endosperm; reduction uses smooth rolls.
Question 2 · hard
A wheat flour contains 2.1% nitrogen. What is its protein content using the wheat factor?
13.1%
11.0%
12.0%
2.1%
Answer and working
C. 12.0%
2.1 × 5.7 = 11.97 ≈ 12.0%. 13.1% uses the general factor 6.25.
Question 3 · easy
Farinograph water absorption is the water needed to bring the dough curve peak to:
500 BU
100 BU
250 BU
1,000 BU
Answer and working
A. 500 BU
Water is adjusted to give a 500 Brabender unit peak.
Question 4 · easy
Head rice is defined as milled rice kernels that are at least:
Three-quarters of full length
One-quarter of full length
Equal to full length
Half of full length
Answer and working
A. Three-quarters of full length
Kernels ≥ 3/4 length are head rice; shorter ones are brokens.
Question 5 · medium
Why is parboiled rice nutritionally better than raw milled rice?
Parboiling adds synthetic vitamins to the grain
Thiamine and minerals migrate into the endosperm before milling
The bran is retained completely after milling
Parboiling destroys all phytate in the grain
Answer and working
B. Thiamine and minerals migrate into the endosperm before milling
Water-soluble nutrients move inward during soaking and steaming.
Question 6 · medium
In maize wet milling, steeping is done in warm water containing:
Sodium chloride
Calcium hydroxide
Ethanol
Sulphur dioxide
Answer and working
D. Sulphur dioxide
SO2 breaks protein disulphide bonds and limits microbial growth; lime is used in nixtamalisation.
Question 7 · medium
Oat groats are kilned or steamed early in processing mainly to:
Remove the hulls without any machinery
Raise the protein content of the flakes
Increase the β-glucan content of the groats
Inactivate lipase and prevent bitter free fatty acids
Answer and working
D. Inactivate lipase and prevent bitter free fatty acids
Oats are high in lipid and lipase; heat stops rancidity.
Question 8 · medium
1000 kg of wheat at 11% moisture is to be tempered to 16% moisture before milling. The water to add is closest to:
50.0 kg
56.2 kg
59.5 kg
5.95 kg
Answer and working
C. 59.5 kg
Dry matter stays at 890 kg, so final mass = 890/0.84 = 1059.5 kg and water added = 59.5 kg; the formula is W = m(M₂ − M₁)/(100 − M₂). 50.0 kg simply multiplies by the 5-point difference. 56.2 kg divides by (100 − M₁) instead of (100 − M₂). 5.95 kg misplaces the decimal.
Question 9 · medium
Farinograph water absorption is defined as the water needed to:
Make the dough reach peak consistency within 1 minute
Centre the curve's peak on the 500 BU line
Hydrate all the gluten proteins completely
Make the dough rest without breaking for 10 minutes
Answer and working
B. Centre the curve's peak on the 500 BU line
Water is adjusted until the dough's maximum consistency centres on 500 BU, and that water, on a 14% moisture basis, is the absorption. The time to peak is development time, not absorption. Gluten hydration is not measured directly. Stability, not absorption, describes how long the curve stays above 500 BU.
Question 10 · hard
Maize is steeped in water with 0.1 to 0.2% sulphur dioxide at about 50 °C before wet milling. The main role of SO₂ is to:
Hydrolyse starch to glucose during the steep
Bleach the germ oil before extraction
Cut protein disulphide bonds to free starch
Gelatinise the starch so it separates easily
Answer and working
C. Cut protein disulphide bonds to free starch
Sulphite reduces disulphide bonds in the glutelin network that holds starch granules, so starch and protein separate cleanly; it also controls microbes in the steep. SO₂ does not hydrolyse starch. Oil is refined separately. Steeping is below the gelatinisation temperature, and gelatinised starch would not separate.
A study plan for Cereal Science & Milling Technology in GATE XL
This plan follows where our questions actually fall, so the time goes where the marks are likely to be. It is our reading of the syllabus, not the exam body's weighting.
First, the heavy units (47% of the 38 questions): Rice milling and parboiling: quality and by-products (5, 13%); Wheat milling: conditioning, break, reduction and flour streams (5, 13%); Dry and wet milling of maize; starch, syrups and germ oil (4, 11%); Flour quality: protein, gluten, falling number and ash (4, 11%).
Read the manual chapters for these first and do every worked question you can find on them.
Then the middle band: Structure and composition of wheat, rice, maize, barley, oats, sorghum and millets (4, 11%); Millet processing and products (3, 8%); Rice bran stabilisation and by-product utilisation (3, 8%); Breakfast cereals and instant cereal products (2, 5%).
Aim for one sitting per unit, then mixed questions across them.
Then the lighter units: Dough rheology tests: farinograph, mixograph, extensograph and alveograph (2, 5%); Malting of barley and other grains (2, 5%); Oat milling and beta-glucans (2, 5%); Starch modification: physical, chemical and enzymatic (2, 5%).
Learn the definitions, classifications and standard numbers; these units are more often recalled than worked.
Leave time for the hard ones: Dry and wet milling of maize; starch, syrups and germ oil (2 hard of 4), Starch modification: physical, chemical and enzymatic (1 hard of 2), Flour quality: protein, gluten, falling number and ash (1 hard of 4).
Come back to these after a first pass, untimed, and read every explanation, including for the options you rejected.
Bank the easy marks: Structure and composition of wheat, rice, maize, barley, oats, sorghum and millets (3 easy of 4); Millet processing and products (2 easy of 3).
Do these early in revision so they are fast on the day.
Finish timed. Sit the subject as a timed set without notes, mark it, and send each wrong answer back to its unit above.