LAISHA
Open Laisha

GATE XL Extrusion & Texturisation Technology: practice questions

GATE — Life Sciences (XL), Section U Food Technology · India · IITs and IISc on rotation (2027: IIT Madras)

Original practice questions written to the published syllabus · not past papers
10worked here, free
48written to this exam in this subject
11syllabus units

About GATE XL

GATE — Life Sciences (XL), Section U Food Technology is a postgraduate admission exam run by IITs and IISc on rotation (2027: IIT Madras), for candidates in India. Computer-based, 3 hours, 100 marks. MCQ, MSQ and NAT. Within XL, Section P Chemistry is understood to be compulsory and the candidate chooses two further sections, of which U Food Technology is one; this structure and the mark split are from earlier brochures and were not re-read for 2026.

Source: gate2026.iitg.ac.in.

Checked against the exam body's published information. Formats and fees change; confirm the current edition there before you book.

Extrusion & Texturisation Technology in GATE XL

Same scope as XE-G; questions often link extrusion to starch and protein chemistry (gelatinisation at low moisture, fragmentation, protein texturisation).

The extruder as a continuous cooker and shaper: single- and twin-screw extruders, the transformations of starch and protein inside them, expanded snacks, breakfast cereals, pasta, and high-moisture extrusion for meat analogues.

Our 48 GATE XL questions in this subject: 19 easy, 16 medium, 13 hard, across 11 units.

10 practice questions, worked

Choose an answer, then open the working. Each explanation says why the right answer is right and why the others are not.

These 10 were written to GATE XL and are not shown on any other exam's page.

Question 1 · easy

The three functional zones of a cooking extruder screw are

  1. mixing, freezing and drying
  2. feed, transition and metering
  3. washing, peeling and cutting
  4. heating, holding and cooling
Answer and working

B. feed, transition and metering

Feed accepts material, transition compresses and melts it, metering pressurises it to the die.

Question 2 · medium

Net output of a single-screw extruder equals

  1. pressure flow plus drag flow
  2. the die flow multiplied by the screw speed in revolutions per second
  3. drag flow minus pressure flow and leakage
  4. leakage flow only
Answer and working

C. drag flow minus pressure flow and leakage

Back-pressure from the die opposes drag flow; leakage over flights reduces output further.

Question 3 · medium

An extrudate leaves the die at 2.0 m/s and is cut by a two-blade knife at 600 rpm. The piece length is about

  1. 20 cm
  2. 5 cm
  3. 0.3 cm
  4. 10 cm
Answer and working

D. 10 cm

Cuts per second = 600/60 × 2 = 20; length = 2.0/20 = 0.10 m = 10 cm. 20 cm ignores the second blade; 5 and 0.3 are slips.

Question 4 · hard

Bubble growth after the die stops when

  1. the matrix cools below its glass transition
  2. the cutter separates the pieces
  3. all the starch becomes fully crystalline again at once
  4. the product reaches 150 °C
Answer and working

A. the matrix cools below its glass transition

Loss of heat and water raises viscosity and sets the glassy structure.

Question 5 · easy

Specific mechanical energy in extrusion is

  1. mechanical energy per unit mass extruded
  2. heat supplied by barrel steam jackets per hour of running
  3. the motor's rated power
  4. the die pressure
Answer and working

A. mechanical energy per unit mass extruded

SME = shaft power / mass flow, in kJ/kg or kWh/t.

Question 6 · medium

Increasing feed moisture in starch extrusion usually

  1. raises melt viscosity and SME
  2. has no effect on viscosity
  3. lowers melt viscosity and SME
  4. stops the extruder
Answer and working

C. lowers melt viscosity and SME

Water plasticises the melt, reducing viscosity, die pressure and mechanical energy.

Question 7 · easy

Seasoning of expanded snacks is usually applied

  1. inside the extruder before the die
  2. after drying, with oil
  3. to the raw grits before milling
  4. during freezing of the snacks
Answer and working

B. after drying, with oil

Oil helps powders adhere after the pieces are dried; seasonings would burn in the barrel.

Question 8 · medium

Adding reverse-pitch elements to the screw profile of a co-rotating twin-screw extruder:

  1. Raises local fill, shear and SME
  2. Lowers residence time and reduces cooking
  3. Converts the extruder to counter-rotating operation
  4. Raises conveying capacity downstream of the element
Answer and working

A. Raises local fill, shear and SME

Reverse elements push material backwards, so the channels upstream fill completely, pressure builds, and shear and SME rise, giving more cooking. Residence time increases, not decreases. The screws still co-rotate. Reverse elements restrict conveying; they do not raise it.

Question 9 · medium

Fibrous whole-cut meat analogues are made by high-moisture extrusion. The feature that creates the aligned fibres is:

  1. Rapid flashing of steam to vapour at the die exit
  2. Grinding the extrudate after it leaves the die
  3. A long cooling die in which the layered melt sets
  4. Adding gluten after extrusion to bind the pieces
Answer and working

C. A long cooling die in which the layered melt sets

At 40 to 80% moisture the protein melt passes through a long cooled die; laminar flow orients the protein phases and cooling sets them before they can relax. Steam expansion at the die belongs to low-moisture TVP and gives a porous, spongy texture. Grinding destroys fibres. Gluten can be an ingredient, but adding it afterwards does not create fibres.

Question 10 · hard

At constant barrel temperature, raising feed moisture of a maize grit from 15% to 25% generally:

  1. Increases expansion because more steam flashes off
  2. Leaves expansion unchanged because moisture evaporates
  3. Increases expansion because SME rises
  4. Decreases expansion and raises bulk density
Answer and working

D. Decreases expansion and raises bulk density

Extra water plasticises the melt, lowering its viscosity and SME and dropping Tg, so bubbles collapse or shrink before the structure sets and the product is denser. More steam is available, but a weak melt cannot hold it. Moisture does change expansion strongly. SME falls, not rises, with more water.

A study plan for Extrusion & Texturisation Technology in GATE XL

This plan follows where our questions actually fall, so the time goes where the marks are likely to be. It is our reading of the syllabus, not the exam body's weighting.

  1. First, the heavy units (52% of the 48 questions): Principles of extrusion cooking (7, 15%); Starch transformations during extrusion (7, 15%); Expanded snacks and ready-to-eat breakfast cereals (6, 13%); Specific mechanical energy and process variables (5, 10%).

    Read the manual chapters for these first and do every worked question you can find on them.

  2. Then the middle band: Die design and product shaping (4, 8%); Pasta and cold-forming extrusion (4, 8%); Quality evaluation of extrudates: expansion ratio and bulk density (4, 8%); Twin-screw extruders: configuration and screw elements (4, 8%).

    Aim for one sitting per unit, then mixed questions across them.

  3. Then the lighter units: Protein texturisation: low-moisture and high-moisture extrusion (3, 6%); Single-screw extruders: flow and pressure (3, 6%); Co-extrusion and filled products (1, 2%).

    Learn the definitions, classifications and standard numbers; these units are more often recalled than worked.

  4. Leave time for the hard ones: Co-extrusion and filled products (1 hard of 1), Starch transformations during extrusion (4 hard of 7), Specific mechanical energy and process variables (2 hard of 5).

    Come back to these after a first pass, untimed, and read every explanation, including for the options you rejected.

  5. Bank the easy marks: Quality evaluation of extrudates: expansion ratio and bulk density (4 easy of 4); Principles of extrusion cooking (4 easy of 7).

    Do these early in revision so they are fast on the day.

  6. Finish timed. Sit the subject as a timed set without notes, mark it, and send each wrong answer back to its unit above.

Last updated · How Laisha writes and checks its pages · Report a mistake

Ask Laisha about this

Opens Laisha's chat with your question ready to send. Sign in or start free.

Unlock every question — GATE XL Extrusion & Texturisation Technology

US$10 a month · one price worldwide · cancel any time

  • Every practice question in this subject, with full working
  • Timed exam papers and progress by unit
  • Ask Laisha to explain any answer — up to 1,000 questions a month
Free or Smarter
FreeSmarter
Grow guides, pest pages, articlesRead allRead all
Ask Laisha5 a dayUp to 1,000 a month
Exam practiceThe sample on each pageEvery question, timed papers
Crop calendar and pest alerts—For your own fields
Calculators and tools—All
Uploads and reports—100 a month, real files
10 days free for every new account, no card.