LAISHA
Open Laisha

GATE XE Extrusion & Texturisation Technology: practice questions

GATE — Engineering Sciences (XE), Section G Food Technology · India · IITs and IISc on rotation (2027: IIT Madras)

Original practice questions written to the published syllabus · not past papers
10worked here, free
38written to this exam in this subject
11syllabus units

About GATE XE

GATE — Engineering Sciences (XE), Section G Food Technology is a postgraduate admission exam run by IITs and IISc on rotation (2027: IIT Madras), for candidates in India. Computer-based, 3 hours, 100 marks. MCQ, MSQ and NAT. General Aptitude is common to every GATE paper; within XE, Section A Engineering Mathematics is compulsory (stated on the 2026 XE-A syllabus) and the candidate chooses two further sections, of which G Food Technology is one. The split of marks between GA, XE-A and the two chosen sections is from Laisha's knowledge of earlier brochures and was not re-read for 2026.

Source: gate2026.iitg.ac.in.

Checked against the exam body's published information. Formats and fees change; confirm the current edition there before you book.

Extrusion & Texturisation Technology in GATE XE

Section 3 names extruded products and ready-to-eat breakfast cereals under cereal processing. Expect questions on extrusion principles, single- versus twin-screw extruders, effects of moisture and temperature on expansion, starch transformation, and calculations of SME, expansion ratio and bulk density.

The extruder as a continuous cooker and shaper: single- and twin-screw extruders, the transformations of starch and protein inside them, expanded snacks, breakfast cereals, pasta, and high-moisture extrusion for meat analogues.

Our 38 GATE XE questions in this subject: 16 easy, 11 medium, 11 hard, across 11 units.

10 practice questions, worked

Choose an answer, then open the working. Each explanation says why the right answer is right and why the others are not.

These 10 were written to GATE XE and are not shown on any other exam's page.

Question 1 · medium

Extrusion improves the nutritional value of legume flours mainly by

  1. adding essential amino acids
  2. inactivating trypsin inhibitors and lectins
  3. increasing lysine availability in all cases
  4. converting starch into protein
Answer and working

B. inactivating trypsin inhibitors and lectins

HTST cooking destroys heat-labile anti-nutrients; severe conditions can, however, reduce available lysine.

Question 2 · hard

An extruder rated 50 kW at 500 rpm runs at 60 % torque and 400 rpm with a total feed of 200 kg/h. Its SME is closest to

  1. 540 kJ/kg
  2. 0.12 kJ/kg
  3. 432 kJ/kg
  4. 900 kJ/kg
Answer and working

C. 432 kJ/kg

Power = 50 × 0.6 × 0.8 = 24 kW; SME = 24/(200/3,600) = 432 kJ/kg. Ignoring the speed fraction gives 540; using kg/h gives 0.12; using rated power gives 900.

Question 3 · hard

An increase in water solubility index (WSI) of an extrudate indicates

  1. more starch fragmentation
  2. less starch conversion
  3. more fat in the product
  4. more protein texturisation
Answer and working

A. more starch fragmentation

WSI rises as starch is broken into soluble fragments (dextrinisation).

Question 4 · hard

Waxy (amylopectin-rich) starches in extrusion tend to give

  1. light, highly expanded products
  2. dense, hard products
  3. products that cannot expand
  4. products with no starch conversion
Answer and working

A. light, highly expanded products

Amylopectin-rich melts often expand more; high-amylose starches give denser products.

Question 5 · hard

High-moisture extrusion of meat analogues uses about

  1. 5–10 % moisture with direct expansion
  2. 20 % moisture with frying
  3. 40–80 % moisture with a cooling die
  4. 100 % water with no protein
Answer and working

C. 40–80 % moisture with a cooling die

High moisture and a cooling die give fibrous, unexpanded products.

Question 6 · easy

Corn curls (collets) are an example of

  1. direct-expanded snacks
  2. third-generation pellets
  3. cold-formed pasta
  4. fried potato slices
Answer and working

A. direct-expanded snacks

They expand at the die and need only drying and seasoning.

Question 7 · easy

Third-generation snack pellets are expanded

  1. inside the extruder barrel before they reach the die
  2. by freezing
  3. later, by frying, hot air or microwave
  4. by adding yeast
Answer and working

C. later, by frying, hot air or microwave

Dense glassy pellets are dried and puffed in a separate step.

Question 8 · hard

Snack pellets are dried to about 10–12 % moisture mainly to

  1. expand them fully
  2. make a stable, glassy intermediate
  3. sterilise them by heat
  4. prepare them for freezing
Answer and working

B. make a stable, glassy intermediate

Dense pellets store and ship cheaply; residual water drives later expansion.

Question 9 · medium

Pasta dough is mixed and extruded under vacuum mainly to

  1. cook the starch
  2. dry the pasta
  3. remove air bubbles that weaken and whiten pasta
  4. add flavour
Answer and working

C. remove air bubbles that weaken and whiten pasta

Air causes weak, opaque pasta and lipoxygenase oxidation of carotenoids.

Question 10 · easy

Products commonly made by extrusion include

  1. canned fish in oil packed in tins
  2. fresh fruit juices pressed from oranges
  3. frozen peas blanched and packed
  4. breakfast cereals and snacks
Answer and working

D. breakfast cereals and snacks

Extrusion makes cereals, snacks, pasta, TVP, pet foods and confectionery.

A study plan for Extrusion & Texturisation Technology in GATE XE

This plan follows where our questions actually fall, so the time goes where the marks are likely to be. It is our reading of the syllabus, not the exam body's weighting.

  1. First, the heavy units (53% of the 38 questions): Principles of extrusion cooking (6, 16%); Expanded snacks and ready-to-eat breakfast cereals (5, 13%); Starch transformations during extrusion (5, 13%); Die design and product shaping (4, 11%).

    Read the manual chapters for these first and do every worked question you can find on them.

  2. Then the middle band: Specific mechanical energy and process variables (4, 11%); Pasta and cold-forming extrusion (3, 8%); Quality evaluation of extrudates: expansion ratio and bulk density (3, 8%); Twin-screw extruders: configuration and screw elements (3, 8%).

    Aim for one sitting per unit, then mixed questions across them.

  3. Then the lighter units: Protein texturisation: low-moisture and high-moisture extrusion (2, 5%); Single-screw extruders: flow and pressure (2, 5%); Co-extrusion and filled products (1, 3%).

    Learn the definitions, classifications and standard numbers; these units are more often recalled than worked.

  4. Leave time for the hard ones: Co-extrusion and filled products (1 hard of 1), Starch transformations during extrusion (3 hard of 5), Specific mechanical energy and process variables (2 hard of 4).

    Come back to these after a first pass, untimed, and read every explanation, including for the options you rejected.

  5. Bank the easy marks: Quality evaluation of extrudates: expansion ratio and bulk density (3 easy of 3); Principles of extrusion cooking (4 easy of 6).

    Do these early in revision so they are fast on the day.

  6. Finish timed. Sit the subject as a timed set without notes, mark it, and send each wrong answer back to its unit above.

Last updated · How Laisha writes and checks its pages · Report a mistake

Ask Laisha about this

Opens Laisha's chat with your question ready to send. Sign in or start free.

Unlock every question — GATE XE Extrusion & Texturisation Technology

US$10 a month · one price worldwide · cancel any time

  • Every practice question in this subject, with full working
  • Timed exam papers and progress by unit
  • Ask Laisha to explain any answer — up to 1,000 questions a month
Free or Smarter
FreeSmarter
Grow guides, pest pages, articlesRead allRead all
Ask Laisha5 a dayUp to 1,000 a month
Exam practiceThe sample on each pageEvery question, timed papers
Crop calendar and pest alerts—For your own fields
Calculators and tools—All
Uploads and reports—100 a month, real files
10 days free for every new account, no card.