LAISHA
Open Laisha

GATE XE Evaporation, Dehydration & Concentration of Foods: practice questions

GATE — Engineering Sciences (XE), Section G Food Technology · India · IITs and IISc on rotation (2027: IIT Madras)

Original practice questions written to the published syllabus · not past papers
10worked here, free
72written to this exam in this subject
13syllabus units

About GATE XE

GATE — Engineering Sciences (XE), Section G Food Technology is a postgraduate admission exam run by IITs and IISc on rotation (2027: IIT Madras), for candidates in India. Computer-based, 3 hours, 100 marks. MCQ, MSQ and NAT. General Aptitude is common to every GATE paper; within XE, Section A Engineering Mathematics is compulsory (stated on the 2026 XE-A syllabus) and the candidate chooses two further sections, of which G Food Technology is one. The split of marks between GA, XE-A and the two chosen sections is from Laisha's knowledge of earlier brochures and was not re-read for 2026.

Source: gate2026.iitg.ac.in.

Checked against the exam body's published information. Formats and fees change; confirm the current edition there before you book.

Evaporation, Dehydration & Concentration of Foods in GATE XE

Section 4 names evaporation of liquid foods, hot-air drying of solids, spray and freeze drying, and psychrometry, humidification and dehumidification; Section 3 names dehydration and intermediate-moisture foods. Expect numericals on humidity ratio and enthalpy of air, air-flow requirements, evaporator mass balance and steam economy, moisture-basis conversion and constant- and falling-rate drying times, plus reasoning on dryer and evaporator selection.

Removing water from liquid and solid foods: evaporator types and energy economy, drying theory and dryer design, spray, drum and freeze drying, concentration by freezing and membranes, and the quality changes that drying causes. Agricultural Engineering's post-harvest-cereals-pulses-oilseeds covers grain drying; this subject covers processed foods and powders.

Our 72 GATE XE questions in this subject: 18 easy, 45 medium, 9 hard, across 13 units.

10 practice questions, worked

Choose an answer, then open the working. Each explanation says why the right answer is right and why the others are not.

These 10 were written to GATE XE and are not shown on any other exam's page.

Question 1 · medium

As air passes over wet food in an adiabatic dryer, its state follows approximately a line of constant

  1. wet-bulb temperature
  2. dry-bulb temperature
  3. humidity ratio
  4. relative humidity
Answer and working

A. wet-bulb temperature

Heat for evaporation comes from the air's sensible heat, so the air cools and gains moisture along a near-constant wet-bulb (and enthalpy) line. Dry-bulb and W both change; RH rises.

Question 2 · medium

Air at 30 °C has a water vapour partial pressure of 2.0 kPa; the saturation vapour pressure at 30 °C is 4.246 kPa. Its relative humidity is closest to

  1. 212 %
  2. 47 %
  3. 1.3 %
  4. 2.0 %
Answer and working

B. 47 %

RH = pv/ps = 2.0/4.246 = 47 %. 212 % inverts the ratio and exceeds 100 %; 1.3 % is the humidity ratio expressed as a percentage; 2.0 % confuses kPa with per cent.

Question 3 · easy

10,000 kg/h of juice at 12 % solids is concentrated to 48 % solids. The water evaporated is

  1. 2,500 kg/h
  2. 7,500 kg/h
  3. 3,600 kg/h
  4. 9,750 kg/h
Answer and working

B. 7,500 kg/h

V = F(1 − xF/xP) = 10,000 × (1 − 12/48) = 7,500 kg/h. 2,500 kg/h is the concentrate; 3,600 kg/h multiplies the feed by the difference in percentages (10,000 × 0.36); 9,750 kg/h treats 12/48 as 2.5 %.

Question 4 · medium

Backward feed in a multiple-effect evaporator is preferred when

  1. the product is heat-sensitive and must never meet the hottest effect
  2. no pumps are allowed between effects
  3. the concentrate is viscous and the feed is cold
  4. the feed is already above the first effect's boiling point
Answer and working

C. the concentrate is viscous and the feed is cold

Backward feed puts the most viscous liquid where temperature is highest and viscosity lowest, improving heat transfer, and suits cold feeds; it needs inter-effect pumps.

Question 5 · medium

A rising-film (climbing-film) evaporator differs from a falling-film evaporator in that

  1. expanding vapour drives the film up the tubes, so a larger ΔT is needed
  2. the liquid flows down the tubes under gravity, so it works with very small differences
  3. the liquid is pumped at high velocity with boiling suppressed inside the tubes
  4. the liquid is spread by rotating blades on a heated cylinder wall
Answer and working

A. expanding vapour drives the film up the tubes, so a larger ΔT is needed

Climbing-film flow depends on vapour generation; falling-film flow uses gravity. The others describe forced-circulation and agitated thin-film evaporators.

Question 6 · medium

If drying is controlled by internal diffusion, halving the thickness of a slab of food changes the drying time to about

  1. one-half of the original
  2. the same as the original
  3. one-quarter of the original
  4. twice the original
Answer and working

C. one-quarter of the original

In the diffusion solution time scales with L², so halving L cuts time to about a quarter.

Question 7 · easy

Drum drying is particularly suitable for

  1. slurries and purées such as potato mash, infant cereal and fruit purée
  2. whole fruit pieces that must keep their shape
  3. dilute juices that must keep delicate aromas
  4. heat-sensitive probiotic cultures
Answer and working

A. slurries and purées such as potato mash, infant cereal and fruit purée

Drum dryers dry a thin film of paste or slurry in seconds to make flakes; whole pieces, aroma-rich juices and live cultures need gentler methods.

Question 8 · medium

Agglomeration (instantising) of a spray-dried powder improves

  1. oxidative stability, by removing all fat from the particle surfaces
  2. bulk density, by producing the finest possible single particles
  3. wettability and dispersibility, so the powder reconstitutes without lumps
  4. microbial safety, by sterilising the powder during rewetting
Answer and working

C. wettability and dispersibility, so the powder reconstitutes without lumps

Larger porous agglomerates wet and sink quickly. Agglomerates have lower bulk density, not higher, and rewetting does not sterilise.

Question 9 · easy

Intermediate-moisture foods typically have a water activity of about

  1. 0.1 to 0.3
  2. 0.95 to 1.0
  3. 0.6 to 0.9
  4. 0.3 to 0.5
Answer and working

C. 0.6 to 0.9

IMFs are soft but shelf-stable, commonly aw 0.6–0.9 with 15–50 % moisture. Below 0.6 foods are dry; above 0.9 most bacteria grow.

Question 10 · medium

The heat that must be removed to freeze 1 kg of water (latent heat of fusion) is about

  1. 2,260 kJ
  2. 2,840 kJ
  3. 334 kJ
  4. 4.18 kJ
Answer and working

C. 334 kJ

Fusion takes about 334 kJ/kg, much less than vaporisation (2,260 kJ/kg) or sublimation (2,840 kJ/kg); 4.18 kJ/kg K is the specific heat of water.

A study plan for Evaporation, Dehydration & Concentration of Foods in GATE XE

This plan follows where our questions actually fall, so the time goes where the marks are likely to be. It is our reading of the syllabus, not the exam body's weighting.

  1. First, the heavy units (50% of the 72 questions): Drying theory: constant-rate and falling-rate periods (8, 11%); Psychrometry, humidification and dehumidification (8, 11%); Evaporation: boiling-point elevation and heat transfer (7, 10%); Single- and multiple-effect evaporators; steam economy (7, 10%); Freeze drying: principles, cycle design and collapse temperature (6, 8%).

    Read the manual chapters for these first and do every worked question you can find on them.

  2. Then the middle band: Spray drying: atomisation, powder properties and agglomeration (6, 8%); Freeze concentration and membrane concentration (5, 7%); Hot-air dryers: cabinet, tunnel, belt and fluidised-bed (5, 7%); Osmotic dehydration and intermediate-moisture foods (5, 7%); Quality changes in dried foods and rehydration (5, 7%).

    Aim for one sitting per unit, then mixed questions across them.

  3. Then the lighter units: Falling-film, forced-circulation and plate evaporators (4, 6%); Drum drying (3, 4%); Vapour recompression: thermal and mechanical (3, 4%).

    Learn the definitions, classifications and standard numbers; these units are more often recalled than worked.

  4. Leave time for the hard ones: Spray drying: atomisation, powder properties and agglomeration (2 hard of 6), Vapour recompression: thermal and mechanical (1 hard of 3), Drying theory: constant-rate and falling-rate periods (2 hard of 8).

    Come back to these after a first pass, untimed, and read every explanation, including for the options you rejected.

  5. Bank the easy marks: Quality changes in dried foods and rehydration (2 easy of 5); Psychrometry, humidification and dehumidification (3 easy of 8).

    Do these early in revision so they are fast on the day.

  6. Finish timed. Sit the subject as a timed set without notes, mark it, and send each wrong answer back to its unit above.

Last updated · How Laisha writes and checks its pages · Report a mistake

Ask Laisha about this

Opens Laisha's chat with your question ready to send. Sign in or start free.

Unlock every question — GATE XE Evaporation, Dehydration & Concentration of Foods

US$10 a month · one price worldwide · cancel any time

  • Every practice question in this subject, with full working
  • Timed exam papers and progress by unit
  • Ask Laisha to explain any answer — up to 1,000 questions a month
Free or Smarter
FreeSmarter
Grow guides, pest pages, articlesRead allRead all
Ask Laisha5 a dayUp to 1,000 a month
Exam practiceThe sample on each pageEvery question, timed papers
Crop calendar and pest alerts—For your own fields
Calculators and tools—All
Uploads and reports—100 a month, real files
10 days free for every new account, no card.