LAISHA
Open Laisha

GATE XE Transport Phenomena in Food Processing: Fluid Flow, Heat & Mass Transfer: practice questions

GATE — Engineering Sciences (XE), Section G Food Technology · India · IITs and IISc on rotation (2027: IIT Madras)

Original practice questions written to the published syllabus · not past papers
10worked here, free
88written to this exam in this subject
15syllabus units

About GATE XE

GATE — Engineering Sciences (XE), Section G Food Technology is a postgraduate admission exam run by IITs and IISc on rotation (2027: IIT Madras), for candidates in India. Computer-based, 3 hours, 100 marks. MCQ, MSQ and NAT. General Aptitude is common to every GATE paper; within XE, Section A Engineering Mathematics is compulsory (stated on the 2026 XE-A syllabus) and the candidate chooses two further sections, of which G Food Technology is one. The split of marks between GA, XE-A and the two chosen sections is from Laisha's knowledge of earlier brochures and was not re-read for 2026.

Source: gate2026.iitg.ac.in.

Checked against the exam body's published information. Formats and fees change; confirm the current edition there before you book.

Transport Phenomena in Food Processing: Fluid Flow, Heat & Mass Transfer in GATE XE

Section 4 names mass and energy balance; momentum transfer (flow rate and pressure drop relationships for Newtonian fluids in pipes, Reynolds number); heat transfer by conduction, convection and radiation and heat exchangers; and mass transfer (Fick's law, convective mass transfer, permeability through single and multilayer films). Expect numerical-answer questions on Reynolds number, Hagen–Poiseuille and Fanning pressure drop, composite-wall conduction, LMTD, Dittus–Boelter, Biot and lumped cooling, and film permeation; units and the Fanning/Darcy distinction are the common traps.

Mass and energy balances and the three transfer processes — momentum, heat and mass — applied to foods: pumping viscous products, heating cans and pouches, and moisture and gas movement through foods and packaging films.

Our 88 GATE XE questions in this subject: 25 easy, 38 medium, 25 hard, across 15 units.

10 practice questions, worked

Choose an answer, then open the working. Each explanation says why the right answer is right and why the others are not.

These 10 were written to GATE XE and are not shown on any other exam's page.

Question 1 · easy

5,000 kg/h of milk at 12 % total solids is concentrated to 45 % total solids. The water evaporated is closest to

  1. 1,333 kg/h
  2. 1,650 kg/h
  3. 3,350 kg/h
  4. 3,667 kg/h
Answer and working

D. 3,667 kg/h

W = F(1 − xF/xP) = 5,000 × (1 − 12/45) = 3,667 kg/h. 1,333 kg/h is the concentrate; 1,650 kg/h multiplies by 0.33 (45 − 12 as a fraction); 3,350 kg/h subtracts percentages (5,000 × 0.67).

Question 2 · easy

Steam is the preferred heating medium in food plants mainly because it

  1. is cheaper to make than hot air in every plant and needs no boiler or water treatment
  2. releases a large latent heat at a constant, pressure-controlled temperature
  3. heats food without any contact with a heat-transfer surface
  4. never forms condensate, so steam traps are not needed
Answer and working

B. releases a large latent heat at a constant, pressure-controlled temperature

Condensing steam delivers about 2,200 kJ/kg at a temperature fixed by its pressure, with very high film coefficients; condensate must be removed by traps.

Question 3 · medium

The Bernoulli equation for an ideal fluid states that along a streamline the sum of

  1. pressure energy and friction energy per unit mass stays constant
  2. pressure, kinetic and potential energy per unit mass is constant
  3. mass flow and heat flow is constant
  4. velocity and viscosity is constant
Answer and working

B. pressure, kinetic and potential energy per unit mass is constant

P/ρ + v²/2 + gz = constant for frictionless, incompressible, steady flow; real flows add pump work and friction terms.

Question 4 · easy

Milk (ρ = 1,030 kg/m³, μ = 2.0 mPa s) flows at 1.5 m/s in a 38 mm tube. The Reynolds number is closest to

  1. 29,355
  2. 29
  3. 29,355,000
  4. 2,936
Answer and working

A. 29,355

Re = ρvD/μ = 1,030 × 1.5 × 0.038/0.002 = 29,355, turbulent. 29 and 29,355,000 come from unit slips in μ (Pa s vs mPa s); 2,936 uses D = 3.8 mm.

Question 5 · medium

Cavitation in a pump is avoided when

  1. the discharge valve is kept fully closed for the whole period of operation
  2. net positive suction head available exceeds that required
  3. the liquid is heated close to its boiling point
  4. the suction line is made long and narrow
Answer and working

B. net positive suction head available exceeds that required

NPSHa must exceed NPSHr so that inlet pressure stays above vapour pressure; hot liquids and restrictive suction lines reduce NPSHa.

Question 6 · medium

In a heat exchanger with a thin stainless-steel wall, the wall usually contributes little to the overall resistance because

  1. metal conductivity is high compared with the fluid films
  2. stainless steel is a perfect insulator at food temperatures
  3. the fluid films always have zero resistance
  4. heat passes around the wall rather than through it
Answer and working

A. metal conductivity is high compared with the fluid films

A 1–2 mm steel wall has resistance far below the convective films and fouling layers.

Question 7 · medium

Natural (free) convection is driven by

  1. a pump or fan moving the fluid
  2. radiation from the hot surface
  3. density differences caused by temperature differences
  4. pressure differences created by a compressor in the circuit
Answer and working

C. density differences caused by temperature differences

Warm fluid is less dense and rises; forced convection uses pumps or fans. The Grashof number characterises it.

Question 8 · hard

A food slab (k = 0.5 W/m K, ρ = 1,000 kg/m³, cp = 3,600 J/kg K) of half-thickness 20 mm is heated for 30 min. The Fourier number is about

  1. 0.156
  2. 0.01042
  3. 0.62
  4. 2.5
Answer and working

C. 0.62

α = k/ρcp = 1.39e-07 m²/s; Fo = αt/L² = 1.39e-07 × 1,800/0.02² = 0.62. 0.156 uses the full thickness 40 mm; 0.01042 uses 30 s; 2.5 uses 10 mm.

Question 9 · hard

A counter-current heat exchanger has equal heat capacity rates (Cr = 1) and NTU = 2.0. Its effectiveness is

  1. 0.865
  2. 0.667
  3. 0.500
  4. 1.000
Answer and working

B. 0.667

For Cr = 1, ε = NTU/(1 + NTU) = 2/3 = 0.667. 0.865 is 1 − e^−2, valid only when Cr = 0; 0.500 is the co-current limit; 1.000 would need infinite NTU.

Question 10 · hard

Water evaporates from a 0.5 m² wet surface with km = 0.02 m/s; vapour concentrations are 0.017 kg/m³ at the surface and 0.008 kg/m³ in the air. The evaporation rate is

  1. 0.17 g/s
  2. 0.08 g/s
  3. 9.0 g/s
  4. 0.09 g/s
Answer and working

D. 0.09 g/s

N = kmA(Cs − C∞) = 0.02 × 0.5 × 0.009 = 9.00e-05 kg/s = 0.09 g/s. 0.17 g/s uses Cs only; 0.08 g/s uses C∞ only; 9.0 g/s is a unit slip.

A study plan for Transport Phenomena in Food Processing: Fluid Flow, Heat & Mass Transfer in GATE XE

This plan follows where our questions actually fall, so the time goes where the marks are likely to be. It is our reading of the syllabus, not the exam body's weighting.

  1. First, the heavy units (41% of the 88 questions): Flow in pipes: Reynolds number, friction factor and pressure drop for Newtonian fluids (8, 9%); Heat exchangers: plate, tubular and scraped-surface; LMTD and effectiveness (8, 9%); Units, dimensions and dimensional analysis (7, 8%); Unsteady-state heat transfer: lumped systems and Heisler charts (7, 8%); Convection: film coefficients and dimensionless numbers (6, 7%).

    Read the manual chapters for these first and do every worked question you can find on them.

  2. Then the middle band: Energy balances and steam tables (6, 7%); Material balances on mixing, concentration and drying (6, 7%); Pumps for foods: centrifugal and positive-displacement (6, 7%); Steady-state conduction through slabs, cylinders and composite walls (6, 7%); Convective mass transfer (5, 6%).

    Aim for one sitting per unit, then mixed questions across them.

  3. Then the lighter units: Fluid statics and the Bernoulli equation (5, 6%); Permeability through single and multilayer films (5, 6%); Radiation heat transfer (5, 6%); Flow of non-Newtonian foods in pipes (4, 5%); Molecular diffusion and Fick's law (4, 5%).

    Learn the definitions, classifications and standard numbers; these units are more often recalled than worked.

  4. Leave time for the hard ones: Heat exchangers: plate, tubular and scraped-surface; LMTD and effectiveness (4 hard of 8), Molecular diffusion and Fick's law (2 hard of 4), Permeability through single and multilayer films (2 hard of 5).

    Come back to these after a first pass, untimed, and read every explanation, including for the options you rejected.

  5. Bank the easy marks: Material balances on mixing, concentration and drying (3 easy of 6); Units, dimensions and dimensional analysis (3 easy of 7).

    Do these early in revision so they are fast on the day.

  6. Finish timed. Sit the subject as a timed set without notes, mark it, and send each wrong answer back to its unit above.

Last updated · How Laisha writes and checks its pages · Report a mistake

Ask Laisha about this

Opens Laisha's chat with your question ready to send. Sign in or start free.

Unlock every question — GATE XE Transport Phenomena in Food Processing: Fluid Flow, Heat & Mass Transfer

US$10 a month · one price worldwide · cancel any time

  • Every practice question in this subject, with full working
  • Timed exam papers and progress by unit
  • Ask Laisha to explain any answer — up to 1,000 questions a month
Free or Smarter
FreeSmarter
Grow guides, pest pages, articlesRead allRead all
Ask Laisha5 a dayUp to 1,000 a month
Exam practiceThe sample on each pageEvery question, timed papers
Crop calendar and pest alerts—For your own fields
Calculators and tools—All
Uploads and reports—100 a month, real files
10 days free for every new account, no card.