GATE — Engineering Sciences (XE), Section G Food Technology · India · IITs and IISc on rotation (2027: IIT Madras)
Original practice questions written to the published syllabus · not past papersGATE — Engineering Sciences (XE), Section G Food Technology is a postgraduate admission exam run by IITs and IISc on rotation (2027: IIT Madras), for candidates in India. Computer-based, 3 hours, 100 marks. MCQ, MSQ and NAT. General Aptitude is common to every GATE paper; within XE, Section A Engineering Mathematics is compulsory (stated on the 2026 XE-A syllabus) and the candidate chooses two further sections, of which G Food Technology is one. The split of marks between GA, XE-A and the two chosen sections is from Laisha's knowledge of earlier brochures and was not re-read for 2026.
Source: gate2026.iitg.ac.in.
Checked against the exam body's published information. Formats and fees change; confirm the current edition there before you book.
Section 4 names size reduction of solids, high-pressure homogenisation, filtration, centrifugation, settling, sieving, and mixing and agitation of liquids. Expect numerical-answer questions on Rittinger, Kick and Bond energies, Stokes settling and centrifugal settling velocities, g-number, constant-pressure filtration time, membrane flux, rejection and concentration factor, screen effectiveness and agitator power from the power number, with equipment-selection reasoning.
The mechanical operations that clean, sort, reduce, mix, homogenise and separate food materials, including filtration, centrifugation and membrane processes, with the design equations used to size them.
Our 83 GATE XE questions in this subject: 17 easy, 47 medium, 19 hard, across 15 units.
Choose an answer, then open the working. Each explanation says why the right answer is right and why the others are not.
These 10 were written to GATE XE and are not shown on any other exam's page.
Aspiration (winnowing) separates chaff and dust from grain mainly by differences in
A. terminal velocity in an air stream
Light chaff has a lower terminal velocity and is carried away by air while grain falls. Colour sorters and magnets use other properties.
Sorting differs from grading in that sorting
D. separates by one measurable property
Sorting uses a single property such as size, weight or colour; grading assesses several quality attributes together against standards.
In the turbulent regime in a baffled tank, doubling impeller speed increases power by a factor of
D. 8
P ∝ N³ when Np is constant; 32 is the factor for doubling diameter (D⁵).
By Stokes' law, the settling velocity of a small particle is proportional to
B. the square of its diameter
v = d²Δρg/18μ, so velocity varies with the square of diameter; doubling d gives four times the settling velocity.
The capacity of a gravity settling tank to remove particles of a given size depends mainly on its
D. surface area
A particle is removed if its settling velocity exceeds flow/surface area (overflow rate), so area, not depth, governs capacity.
In constant-pressure filtration with negligible medium resistance, collecting 1 m³ of filtrate takes 10 min. Collecting 2 m³ takes
A. 40 min
t ∝ V², so t = 10 × 2² = 40 min. 20 min assumes t ∝ V; 14 min uses √2; 80 min uses V³.
Reverse osmosis cannot concentrate fruit juice much beyond about 25–30 % solids mainly because
D. osmotic pressure rises with concentration and opposes the applied pressure
π = icRT grows with solute concentration, so very high pressures would be needed; RO is used to pre-concentrate.
Making the particles extremely fine in a percolation extractor can reduce performance because
B. very fine particles impede drainage of solvent through the bed
Short diffusion paths help, but fines pack tightly and block solvent flow.
High supersaturation during crystallisation tends to produce
D. many small crystals
High supersaturation favours nucleation over growth.
A screw conveyor has D = 0.2 m, shaft d = 0.05 m, pitch 0.2 m, speed 60 rpm and loading 0.4. Its volumetric capacity is closest to
D. 8.5 m³/h
Q = (π/4)(0.04 − 0.0025) × 0.2 × 1 rev/s × 0.4 = 0.00236 m³/s = 8.5 m³/h. Ignoring the shaft gives 9.0; using 60 rev/s gives the large value; omitting loading gives 21.2.
This plan follows where our questions actually fall, so the time goes where the marks are likely to be. It is our reading of the syllabus, not the exam body's weighting.
Read the manual chapters for these first and do every worked question you can find on them.
Aim for one sitting per unit, then mixed questions across them.
Learn the definitions, classifications and standard numbers; these units are more often recalled than worked.
Come back to these after a first pass, untimed, and read every explanation, including for the options you rejected.
Do these early in revision so they are fast on the day.
Last updated · How Laisha writes and checks its pages · Report a mistake
US$10 a month · one price worldwide · cancel any time
| Free | Smarter | |
|---|---|---|
| Grow guides, pest pages, articles | Read all | Read all |
| Ask Laisha | 5 a day | Up to 1,000 a month |
| Exam practice | The sample on each page | Every question, timed papers |
| Crop calendar and pest alerts | — | For your own fields |
| Calculators and tools | — | All |
| Uploads and reports | — | 100 a month, real files |
An AI operating system for agriculture: free guides, manuals and tools written for every country.