LAISHA
Open Laisha

GATE XE Thermal Processing & Canning Technology: practice questions

GATE — Engineering Sciences (XE), Section G Food Technology · India · IITs and IISc on rotation (2027: IIT Madras)

Original practice questions written to the published syllabus · not past papers
10worked here, free
52written to this exam in this subject
12syllabus units

About GATE XE

GATE — Engineering Sciences (XE), Section G Food Technology is a postgraduate admission exam run by IITs and IISc on rotation (2027: IIT Madras), for candidates in India. Computer-based, 3 hours, 100 marks. MCQ, MSQ and NAT. General Aptitude is common to every GATE paper; within XE, Section A Engineering Mathematics is compulsory (stated on the 2026 XE-A syllabus) and the candidate chooses two further sections, of which G Food Technology is one. The split of marks between GA, XE-A and the two chosen sections is from Laisha's knowledge of earlier brochures and was not re-read for 2026.

Source: gate2026.iitg.ac.in.

Checked against the exam body's published information. Formats and fees change; confirm the current edition there before you book.

Thermal Processing & Canning Technology in GATE XE

Section 3 lists thermal processing, aseptic packaging and food standards; Section 4 lists thermal sterilisation alongside heat transfer. Expect numerical-answer questions on D from survivor counts, z from two D values, lethal rate and F0 for a constant hold, log reductions and spoilage probability, and short reasoning items on acid versus low-acid foods, cold spot and HTST/UHT quality advantage. Traps are the sign of the lethal-rate exponent, natural versus common logarithms, and minutes versus seconds.

Designing and validating heat processes that make food safe and shelf-stable: microbial death kinetics, heat penetration, process calculation by the general and formula methods, retorts and aseptic systems, and the regulatory framework for low-acid canned foods. Agricultural Engineering's food-dairy-engineering introduces D, z and F; this subject teaches the full process-establishment practice.

Our 52 GATE XE questions in this subject: 15 easy, 30 medium, 7 hard, across 12 units.

10 practice questions, worked

Choose an answer, then open the working. Each explanation says why the right answer is right and why the others are not.

These 10 were written to GATE XE and are not shown on any other exam's page.

Question 1 · medium

Which statement about the effect of the heating medium on spore heat resistance is correct?

  1. Low water activity and high fat content tend to protect spores and raise their D value
  2. Low pH tends to protect spores, so acid foods need longer processes than low-acid foods
  3. Spores show the same D value in every food, so values from buffer can be used directly
  4. Added salt at any level always makes spores far more heat resistant than in water
Answer and working

A. Low water activity and high fat content tend to protect spores and raise their D value

Dry or fatty surroundings protect spores and raise D, which is why D must be measured in the product. Low pH lowers heat resistance and stops C. botulinum growth, so acid foods need milder processes; D in buffer is not transferable to foods; salt effects depend on concentration and are not uniformly protective.

Question 2 · medium

A can's cold spot is held at a constant 113 °C for 40 min. With z = 10 °C and reference 121.1 °C, the F₀ delivered is closest to

  1. 258 min
  2. 6.2 min
  3. 32.4 min
  4. 40.0 min
Answer and working

B. 6.2 min

L = 10^((113 − 121.1)/10) = 10^(−0.81) = 0.155; F₀ = 40 × 0.155 = 6.2 min. 258 min reverses the sign, crediting more lethality at a lower temperature; 32.4 min multiplies by the exponent; 40.0 min ignores that 113 °C is below the reference.

Question 3 · medium

Product is held at 131.1 °C for 30 s. With z = 10 °C and reference 121.1 °C, the F₀ is

  1. 5.0 min
  2. 0.05 min
  3. 30 min
  4. 0.5 min
Answer and working

A. 5.0 min

L = 10^((131.1 − 121.1)/10) = 10; F₀ = 0.5 min × 10 = 5.0 min. 0.05 min uses the wrong sign; 30 min treats seconds as minutes and multiplies by one; 0.5 min ignores the higher temperature.

Question 4 · hard

A process must deliver F₀ = 3.0 min, but the product can only be held at a constant 116 °C. The holding time needed (z = 10 °C, reference 121.1 °C, ignore come-up and cooling) is closest to

  1. 9.7 min
  2. 0.93 min
  3. 15.3 min
  4. 5.9 min
Answer and working

A. 9.7 min

L at 116 °C = 10^(−0.51) = 0.309; t = F/L = 3.0/0.309 = 9.7 min. 0.93 min multiplies instead of dividing; 15.3 and 5.9 min use the exponent 0.51 directly.

Question 5 · easy

The pH below which (at or below) Clostridium botulinum is regarded as unable to grow and produce toxin in foods is

  1. 5.6
  2. 3.7
  3. 7.0
  4. 4.6
Answer and working

D. 4.6

pH 4.6 is the dividing line between low-acid and acid foods for botulism control. 3.7 is a common boundary between acid and high-acid classes; 5.6 and 7.0 are well within the range where the organism grows.

Question 6 · medium

In a heat penetration test the retort is at 121.1 °C and the true initial product temperature is 70 °C. Extending the straight heating line back to zero time gives a pseudo-initial temperature of 30 °C. The lag factor jh is closest to

  1. 0.56
  2. 0.42
  3. 1.78
  4. 2.33
Answer and working

C. 1.78

jh = (TR − T_pih)/(TR − T_ih) = (121.1 − 30)/(121.1 − 70) = 91.1/51.1 = 1.78. 0.56 inverts the ratio; 0.42 divides by the retort temperature; 2.33 compares the two temperatures directly.

Question 7 · medium

Swollen cans of an acid fruit contain hydrogen gas and no viable microorganisms. The most likely cause is

  1. underprocessing that allowed Clostridium botulinum to grow and produce gas
  2. acid corrosion of the tinplate
  3. post-process leakage that let air into the can during cooling
  4. thermophilic spoilage by flat-sour organisms after slow cooling
Answer and working

B. acid corrosion of the tinplate

Hydrogen swell results from acid attacking the metal; it is chemical, not microbial. C. botulinum does not grow in acid fruit; air entry does not produce hydrogen; flat-sour organisms produce acid without gas. The corroding tinplate releases the hydrogen.

Question 8 · medium

Compared with a cylindrical can of the same volume, a retort pouch generally needs a shorter process time because

  1. the multilayer laminate conducts heat far better than tinplate or aluminium does
  2. pouches need a lower F₀ because botulinum cannot grow in them
  3. its thin profile shortens the heat path
  4. the product in a pouch always heats by convection, never by conduction
Answer and working

C. its thin profile shortens the heat path

The slab-like shape gives a short path to the centre, so the cold spot heats faster. Laminates do not conduct better than metal; the F₀ target is the same; contents may still heat by conduction. The heat path meant is the distance heat must travel to the cold spot.

Question 9 · easy

In aseptic processing and packaging,

  1. food is sealed in its can first and then heated in a retort
  2. only the package is sterilised, and the food is filled cold and raw
  3. food and package are sterilised separately and combined in a sterile zone
  4. the food is filled raw and then irradiated inside its sealed carton after filling and coding
Answer and working

C. food and package are sterilised separately and combined in a sterile zone

Aseptic systems sterilise the product by rapid heating and the package by chemical or thermal means, then fill and seal in sterile conditions. In-container retorting is conventional canning.

Question 10 · medium

Packaging material for aseptic cartons is commonly sterilised with

  1. chlorine dioxide gas inside the filled carton
  2. ethanol sprayed on after filling
  3. ultraviolet light applied after sealing
  4. hydrogen peroxide followed by hot air to remove residues
Answer and working

D. hydrogen peroxide followed by hot air to remove residues

Hydrogen peroxide with heat is the most widely used sterilant for aseptic carton material and bottles. Sterilisation must happen before filling and sealing, not after.

A study plan for Thermal Processing & Canning Technology in GATE XE

This plan follows where our questions actually fall, so the time goes where the marks are likely to be. It is our reading of the syllabus, not the exam body's weighting.

  1. First, the heavy units (54% of the 52 questions): Thermal death kinetics: D value, z value and the thermal death time curve (9, 17%); Lethality, F0 and the 12D concept (8, 15%); Acid and low-acid foods; pH 4.6 and the target organism (6, 12%); Commercial sterility and spoilage probability (5, 10%).

    Read the manual chapters for these first and do every worked question you can find on them.

  2. Then the middle band: Heat penetration tests and cold-spot determination (5, 10%); Aseptic processing and packaging (4, 8%); Process calculation: the general method (4, 8%); Quality optimisation: cook value and nutrient retention (4, 8%).

    Aim for one sitting per unit, then mixed questions across them.

  3. Then the lighter units: Pasteurisation of acid and acidified foods (2, 4%); Process calculation: Ball's formula method (2, 4%); Retort types: still, rotary, hydrostatic and continuous (2, 4%); Retort pouches and flexible containers (1, 2%).

    Learn the definitions, classifications and standard numbers; these units are more often recalled than worked.

  4. Leave time for the hard ones: Process calculation: the general method (2 hard of 4), Process calculation: Ball's formula method (1 hard of 2), Aseptic processing and packaging (1 hard of 4).

    Come back to these after a first pass, untimed, and read every explanation, including for the options you rejected.

  5. Bank the easy marks: Quality optimisation: cook value and nutrient retention (2 easy of 4); Pasteurisation of acid and acidified foods (1 easy of 2).

    Do these early in revision so they are fast on the day.

  6. Finish timed. Sit the subject as a timed set without notes, mark it, and send each wrong answer back to its unit above.

Last updated · How Laisha writes and checks its pages · Report a mistake

Ask Laisha about this

Opens Laisha's chat with your question ready to send. Sign in or start free.

Unlock every question — GATE XE Thermal Processing & Canning Technology

US$10 a month · one price worldwide · cancel any time

  • Every practice question in this subject, with full working
  • Timed exam papers and progress by unit
  • Ask Laisha to explain any answer — up to 1,000 questions a month
Free or Smarter
FreeSmarter
Grow guides, pest pages, articlesRead allRead all
Ask Laisha5 a dayUp to 1,000 a month
Exam practiceThe sample on each pageEvery question, timed papers
Crop calendar and pest alerts—For your own fields
Calculators and tools—All
Uploads and reports—100 a month, real files
10 days free for every new account, no card.