LAISHA
Open Laisha

ICAR AIEEA-PG / PGS Thermal Processing & Canning Technology: practice questions

ICAR AIEEA-PG / PGS — Code 18 Food Science Technology · India · ICAR through the National Testing Agency

Original practice questions written to the published syllabus · not past papers
10worked here, free
46written to this exam in this subject
13syllabus units

About ICAR AIEEA-PG / PGS

ICAR AIEEA-PG / PGS — Code 18 Food Science Technology is a postgraduate admission exam run by ICAR through the National Testing Agency, for candidates in India. Computer-based, multiple choice, +4/−1 marking.

Source: icar.org.in.

Checked against the exam body's published information. Formats and fees change; confirm the current edition there before you book.

Thermal Processing & Canning Technology in ICAR AIEEA-PG / PGS

Unit II names thermobacteriology, pasteurisation and sterilisation; Unit III names canning, packaging and containers. Questions are MCQs at definition and short-calculation level: 12D and F0, commercial sterility, acid classes, types of spoilage (flat sour, TA, sulphide), double-seam parts and faults, retort types and aseptic processing.

Designing and validating heat processes that make food safe and shelf-stable: microbial death kinetics, heat penetration, process calculation by the general and formula methods, retorts and aseptic systems, and the regulatory framework for low-acid canned foods. Agricultural Engineering's food-dairy-engineering introduces D, z and F; this subject teaches the full process-establishment practice.

Our 46 ICAR AIEEA-PG / PGS questions in this subject: 22 easy, 23 medium, 1 hard, across 13 units.

10 practice questions, worked

Choose an answer, then open the working. Each explanation says why the right answer is right and why the others are not.

These 10 were written to ICAR AIEEA-PG / PGS and are not shown on any other exam's page.

Question 1 · medium

Under the United States definition widely used in trade, a low-acid food is one with

  1. equilibrium pH above 4.6 and water activity above 0.95
  2. initial brine pH above 4.0 and moisture above 60 %
  3. equilibrium pH above 4.6 and water activity above 0.85
  4. equilibrium pH above 5.6 and any value of water activity
Answer and working

C. equilibrium pH above 4.6 and water activity above 0.85

21 CFR 113 defines low-acid foods as those with finished equilibrium pH greater than 4.6 and water activity greater than 0.85 (alcoholic beverages excluded). Initial brine pH is not the criterion; 0.95 and 5.6 are not the regulatory values.

Question 2 · medium

Swollen cans from one production lot yield a mixed flora of cocci, short rods and some spore-formers. The most likely cause is

  1. post-process leakage through seams
  2. underprocessing in the retort, leaving only heat-resistant survivors
  3. thermophilic spoilage from slow cooling and hot storage
  4. pre-process spoilage in which growth stopped before retorting
Answer and working

A. post-process leakage through seams

Cocci and other non-spore-formers cannot survive a retort process, so their presence points to contamination after processing, usually through faulty seams. Underprocessing typically leaves a pure culture of spore-formers; thermophilic spoilage gives thermophilic spore-formers; pre-process spoilage shows growth without viable organisms. Leakage typically happens during cooling.

Question 3 · medium

A can with both ends bulged that can be pushed in by thumb pressure but return when released is described as a

  1. flipper
  2. springer
  3. soft swell
  4. hard swell
Answer and working

C. soft swell

A soft swell has both ends bulged but yielding to pressure. A flipper looks normal until struck; a springer has one end bulged that can be pushed in, making the other bulge; a hard swell cannot be pushed in at all.

Question 4 · medium

During visual seam inspection an operator finds a seam where the cover hook and body hook are not interlocked at one point. This fault is called a

  1. cut-over
  2. deadhead
  3. false seam
  4. vee
Answer and working

C. false seam

A false seam is a section where the hooks do not interlock, a serious leak risk. A cut-over is metal fractured over the chuck; a deadhead is an incompletely rolled seam where the chuck slipped; a vee is a projection of metal at the bottom of the seam, often at the side seam.

Question 5 · easy

Venting a steam retort at the start of the cycle is essential because

  1. steam must be removed so that the cans can be heated by hot air instead
  2. venting raises the pressure so that cans heat faster than in pure steam
  3. vents remove condensate only, and air in the retort has no effect
  4. air left in the retort creates cooler zones where cans are underprocessed
Answer and working

D. air left in the retort creates cooler zones where cans are underprocessed

A steam-air mixture is cooler than pure steam at the same pressure, and air pockets insulate containers, so air must be vented. Steam is the heating medium; venting does not raise pressure; bleeders and drains handle condensate.

Question 6 · easy

Glass jars and retort pouches are usually processed in water-immersion, water-spray or steam-air retorts rather than pure saturated steam because these retorts

  1. allow an overriding air pressure independent of temperature to protect the package
  2. operate below 100 °C throughout, so that glass and plastic do not soften during the cycle
  3. need no venting and no temperature control, so they are cheaper to run
  4. heat the food by microwaves, which pass through glass and plastic easily
Answer and working

A. allow an overriding air pressure independent of temperature to protect the package

Overpressure keeps lids and seals in place against the internal pressure of the hot contents. These retorts work at sterilising temperatures above 100 °C, still need temperature control, and heat by conventional means.

Question 7 · medium

The aluminium foil layer in a retort pouch laminate mainly provides

  1. a barrier to oxygen, light and moisture
  2. the heat seal between the two pouch walls
  3. the printing surface for labels
  4. stiffness so that the pouch stands upright
Answer and working

A. a barrier to oxygen, light and moisture

Foil gives an almost complete barrier to gases, light and moisture, which gives long shelf life. Sealing is by the polypropylene inner layer; printing is usually on or under the polyester outer layer.

Question 8 · easy

The cook value C is usually expressed with

  1. reference 121.1 °C and z = 10 °C
  2. reference 72 °C and z = 5 °C
  3. reference 0 °C and z = 18 °C
  4. reference 100 °C and z = 33 °C
Answer and working

D. reference 100 °C and z = 33 °C

The cook value uses a quality z (commonly 33 °C) at 100 °C. 121.1 °C with z = 10 °C defines F₀; the others are not standard cook-value conventions.

Question 9 · easy

A process authority, in low-acid canning regulation, is

  1. the government food inspector who must sign every batch record before the product can be released
  2. an expert person or body in thermal processing who establishes the scheduled processes
  3. the machine that controls the retort steam valve automatically
  4. the retailer who decides the shelf life printed on each can
Answer and working

B. an expert person or body in thermal processing who establishes the scheduled processes

Process authorities have the expertise and facilities to design heat penetration and distribution studies and set scheduled processes. Inspectors, controllers and retailers have other roles.

Question 10 · easy

The international Codex text that sets hygiene requirements for low-acid canned foods is the

  1. General Standard for the Labelling of Prepackaged Foods
  2. Code of Practice for the Prevention of Aflatoxin in Peanuts
  3. General Standard for Food Additives
  4. Code of Hygienic Practice for Low-Acid and Acidified Low-Acid Canned Foods
Answer and working

D. Code of Hygienic Practice for Low-Acid and Acidified Low-Acid Canned Foods

The Code of Hygienic Practice for Low-Acid and Acidified Low-Acid Canned Foods covers scheduled processes, retort operation, containers and records. The other Codex texts cover labelling, aflatoxin and additives.

A study plan for Thermal Processing & Canning Technology in ICAR AIEEA-PG / PGS

This plan follows where our questions actually fall, so the time goes where the marks are likely to be. It is our reading of the syllabus, not the exam body's weighting.

  1. First, the heavy units (61% of the 46 questions): Acid and low-acid foods; pH 4.6 and the target organism (7, 15%); Can making, double seams and seam evaluation (6, 13%); Commercial sterility and spoilage probability (5, 11%); Lethality, F0 and the 12D concept (5, 11%); Retort types: still, rotary, hydrostatic and continuous (5, 11%).

    Read the manual chapters for these first and do every worked question you can find on them.

  2. Then the middle band: Heat penetration tests and cold-spot determination (3, 7%); Pasteurisation of acid and acidified foods (3, 7%); Thermal death kinetics: D value, z value and the thermal death time curve (3, 7%); Aseptic processing and packaging (2, 4%); Quality optimisation: cook value and nutrient retention (2, 4%).

    Aim for one sitting per unit, then mixed questions across them.

  3. Then the lighter units: Regulatory control of low-acid canned foods and process authorities (2, 4%); Retort pouches and flexible containers (2, 4%); Process calculation: the general method (1, 2%).

    Learn the definitions, classifications and standard numbers; these units are more often recalled than worked.

  4. Leave time for the hard ones: Retort types: still, rotary, hydrostatic and continuous (1 hard of 5).

    Come back to these after a first pass, untimed, and read every explanation, including for the options you rejected.

  5. Bank the easy marks: Thermal death kinetics: D value, z value and the thermal death time curve (3 easy of 3); Quality optimisation: cook value and nutrient retention (2 easy of 2).

    Do these early in revision so they are fast on the day.

  6. Finish timed. Sit the subject as a timed set without notes, mark it, and send each wrong answer back to its unit above.

Last updated · How Laisha writes and checks its pages · Report a mistake

Ask Laisha about this

Opens Laisha's chat with your question ready to send. Sign in or start free.

Unlock every question — ICAR AIEEA-PG / PGS Thermal Processing & Canning Technology

US$10 a month · one price worldwide · cancel any time

  • Every practice question in this subject, with full working
  • Timed exam papers and progress by unit
  • Ask Laisha to explain any answer — up to 1,000 questions a month
Free or Smarter
FreeSmarter
Grow guides, pest pages, articlesRead allRead all
Ask Laisha5 a dayUp to 1,000 a month
Exam practiceThe sample on each pageEvery question, timed papers
Crop calendar and pest alerts—For your own fields
Calculators and tools—All
Uploads and reports—100 a month, real files
10 days free for every new account, no card.