ICAR AICE-JRF/SRF (PhD) — Food Processing Technology, Food Safety & Quality, Processing and Food Engineering · India · ICAR through the National Testing Agency
Original practice questions written to the published syllabus · not past papersICAR AICE-JRF/SRF (PhD) — Food Processing Technology, Food Safety & Quality, Processing and Food Engineering is a PhD, fellowship and lectureship exam run by ICAR through the National Testing Agency, for candidates in India. Computer-based, multiple choice.
Source: icar.org.in.
Checked against the exam body's published information. Formats and fees change; confirm the current edition there before you book.
41 Units 2 and 5 cover heat and mass transfer and design of processing machinery. Expect deeper questions on non-Newtonian flow, unsteady conduction and Heisler charts, effectiveness–NTU, and the heat–mass transfer analogy.
Mass and energy balances and the three transfer processes — momentum, heat and mass — applied to foods: pumping viscous products, heating cans and pouches, and moisture and gas movement through foods and packaging films.
Our 54 ICAR AICE-JRF/SRF questions in this subject: 0 easy, 29 medium, 25 hard, across 15 units.
Choose an answer, then open the working. Each explanation says why the right answer is right and why the others are not.
These 10 were written to ICAR AICE-JRF/SRF and are not shown on any other exam's page.
Which of these is NOT dimensionally consistent as written?
A. Q = m cp / ΔT
Heat (J) = kg × J/(kg K) × K; dividing by ΔT gives J/K², inconsistent. m λ gives J; hAΔT t gives J.
In drying calculations, the component usually chosen as the 'tie' component is
D. the dry solids
Dry solids pass through unchanged, linking feed and product; water is what changes.
As the saturation pressure of steam increases, its latent heat of vaporisation
D. decreases
hfg falls with rising pressure and temperature, reaching zero at the critical point; 2,257 kJ/kg applies at 100 °C.
Orifice plates are seldom used to meter milk in hygienic process lines mainly because they
D. are hard to clean and cause permanent pressure loss
Orifices create crevices and dead zones and large permanent losses; magnetic and Coriolis meters are preferred for hygienic duty.
For the milk at Re = 29,355 in a smooth 38 mm tube (ρ = 1,030 kg/m³, v = 1.5 m/s), using Blasius f = 0.0791 Re^−0.25 (Fanning), the pressure drop over 20 m is closest to
D. 14.7 kPa
f = 0.0791 × 29,355^−0.25 = 0.00604; ΔP = 4f(L/D)(ρv²/2) = 14,742 Pa ≈ 14.7 kPa. 3.69 kPa drops the factor 4 of the Fanning form; 59 kPa treats f as Fanning but applies an extra 4; 1.33 kPa wrongly uses the laminar f = 16/Re.
Doubling the velocity of a Newtonian liquid in laminar flow through the same pipe changes the frictional pressure drop by a factor of
C. 2
Hagen–Poiseuille: ΔP ∝ v in laminar flow. In turbulent smooth-pipe flow (Blasius) ΔP ∝ v^1.75, about 3.4 times; 4 would apply to fully rough turbulent flow.
A plant switches from pumping juice to pumping a thick fruit purée through the same line. Which change is most likely to be needed?
C. Replace the centrifugal pump with a positive-displacement pump
Viscous, shear-thinning purées flow laminar with high pressure drop; centrifugal pumps lose efficiency badly, PD pumps handle them. Cooling raises viscosity; longer pipes raise pressure drop.
Insulation (k = 0.04 W/m K) on a pipe extends from r1 = 25 mm to r2 = 50 mm. With 90 °C at the inner and 30 °C at the outer surface, the heat loss per metre is closest to
B. 21.8 W/m
q/L = 2πk(T1 − T2)/ln(r2/r1) = 2π × 0.04 × 60/ln 2 = 21.8 W/m. 15.1 W/m treats the layer as a flat wall of inner area; 50 W/m uses log₁₀; 10.5 W/m multiplies by ln 2.
For the counter-current exchanger with LMTD 24.7 K, U = 1,500 W/m² K and area 10 m², the heat duty is closest to
B. 370 kW
Q = UA·LMTD = 1,500 × 10 × 24.66 = 369,946 W ≈ 370 kW. 370,000 kW forgets W→kW; 375 kW uses the arithmetic mean 25 K; 15 kW omits the LMTD.
A process engineer finds that a CIP circuit gives a cleaning velocity of only 0.6 m/s in a 50 mm line. Since about 1.5 m/s is commonly recommended for turbulent cleaning, the flow should be increased by a factor of about
B. 2.5
Velocity ∝ flow in the same pipe: 1.5/0.6 = 2.5. 0.4 inverts it; 6.3 squares the ratio.
This plan follows where our questions actually fall, so the time goes where the marks are likely to be. It is our reading of the syllabus, not the exam body's weighting.
Read the manual chapters for these first and do every worked question you can find on them.
Aim for one sitting per unit, then mixed questions across them.
Learn the definitions, classifications and standard numbers; these units are more often recalled than worked.
Come back to these after a first pass, untimed, and read every explanation, including for the options you rejected.
Last updated · How Laisha writes and checks its pages · Report a mistake
US$10 a month · one price worldwide · cancel any time
| Free | Smarter | |
|---|---|---|
| Grow guides, pest pages, articles | Read all | Read all |
| Ask Laisha | 5 a day | Up to 1,000 a month |
| Exam practice | The sample on each page | Every question, timed papers |
| Crop calendar and pest alerts | — | For your own fields |
| Calculators and tools | — | All |
| Uploads and reports | — | 100 a month, real files |
An AI operating system for agriculture: free guides, manuals and tools written for every country.