LAISHA
Open Laisha

ICAR AICE-JRF/SRF Extrusion & Texturisation Technology: practice questions

ICAR AICE-JRF/SRF (PhD) — Food Processing Technology, Food Safety & Quality, Processing and Food Engineering · India · ICAR through the National Testing Agency

Original practice questions written to the published syllabus · not past papers
10worked here, free
67written to this exam in this subject
11syllabus units

About ICAR AICE-JRF/SRF

ICAR AICE-JRF/SRF (PhD) — Food Processing Technology, Food Safety & Quality, Processing and Food Engineering is a PhD, fellowship and lectureship exam run by ICAR through the National Testing Agency, for candidates in India. Computer-based, multiple choice.

Source: icar.org.in.

Checked against the exam body's published information. Formats and fees change; confirm the current edition there before you book.

Extrusion & Texturisation Technology in ICAR AICE-JRF/SRF

35.a Unit 2 names extruded products, breakfast and snack foods and texturised vegetable proteins; 41 covers process technology and machinery. Expect deeper questions on screw configuration, SME, RTD, starch fragmentation, high-moisture extrusion and co-extrusion.

The extruder as a continuous cooker and shaper: single- and twin-screw extruders, the transformations of starch and protein inside them, expanded snacks, breakfast cereals, pasta, and high-moisture extrusion for meat analogues.

Our 67 ICAR AICE-JRF/SRF questions in this subject: 9 easy, 35 medium, 23 hard, across 11 units.

10 practice questions, worked

Choose an answer, then open the working. Each explanation says why the right answer is right and why the others are not.

These 10 were written to ICAR AICE-JRF/SRF and are not shown on any other exam's page.

Question 1 · hard

A screw with D = 0.08 m turns at 2 rev/s with helix angle 17.7°; the channel is 0.06 m wide and 0.006 m deep. Using Qd = ½VzWH with Vz = πDN cos θ, the drag flow is closest to

  1. 0.62 m³/h
  2. 0.31 m³/h
  3. 0.33 m³/h
  4. 8.62e-05 m³/h
Answer and working

B. 0.31 m³/h

Vz = π × 0.08 × 2 × cos 17.7° = 0.479 m/s; Qd = ½ × 0.479 × 0.06 × 0.006 = 8.62e-05 m³/s = 0.31 m³/h. Doubling omits the ½; omitting cos θ gives 0.33; the last leaves the value in m³/s.

Question 2 · medium

Grooved barrels are used in single-screw food extruders to

  1. prevent slip at the barrel wall
  2. heat the material by radiation
  3. separate fat from the melt
  4. reduce die pressure
Answer and working

A. prevent slip at the barrel wall

If material slips and turns with the screw, conveying fails; grooves grip it.

Question 3 · hard

Using a die with smaller openings on the same extruder generally

  1. lowers die pressure and raises output
  2. raises die pressure and lowers output
  3. has no effect on pressure
  4. stops the screw rotating
Answer and working

B. raises die pressure and lowers output

A more restrictive die shifts the operating point along the screw characteristic.

Question 4 · medium

Food twin-screw extruders commonly have length-to-diameter ratios of about

  1. 2–4
  2. 200–400
  3. 0.2–0.4
  4. 20–40
Answer and working

D. 20–40

L/D of roughly 20–40 allows feeding, cooking, venting and pressurising zones.

Question 5 · medium

Vitamins are usually added to extruded cereals

  1. after extrusion, by spraying or coating
  2. before extrusion, so that they survive the barrel heat
  3. only in the die
  4. never
Answer and working

A. after extrusion, by spraying or coating

Thiamin, vitamin C and folate are heat-sensitive and lost in the extruder.

Question 6 · hard

A meat analogue needs 45 N to cut perpendicular to its fibres and 15 N parallel to them. Its anisotropy index is

  1. 0.33
  2. 3.0
  3. 30
  4. 60
Answer and working

B. 3.0

45/15 = 3.0; values above 1 indicate fibrousness. 0.33 inverts; 30 subtracts; 60 adds.

Question 7 · medium

Switching to a different supplier's pea protein changes meat-analogue texture markedly. The best response is to

  1. specify protein functionality and re-run extrusion trials
  2. ignore the change
  3. raise the price
  4. stop using a cooling die and expand the product at the die instead
Answer and working

A. specify protein functionality and re-run extrusion trials

Protein solubility and gelling vary between ingredients; specifications and trials keep texture consistent.

Question 8 · hard

Halving the radius of a circular die opening, other things equal, raises the die pressure drop by a factor of

  1. 2
  2. 4
  3. 16
  4. 8
Answer and working

C. 16

ΔP ∝ 1/R⁴; halving R multiplies ΔP by 2⁴ = 16.

Question 9 · hard

Phase separation between protein-rich and water- or polysaccharide-rich phases in high-moisture extrusion is thought to

  1. prevent any fibre formation in the cooling die
  2. contribute to the layered, fibrous structure
  3. cause expansion at the die
  4. convert protein into starch
Answer and working

B. contribute to the layered, fibrous structure

Separated phases are elongated in the cooling die, adding anisotropy.

Question 10 · easy

Dried pasta is dried to a final moisture of about

  1. 30 %, the dough moisture before drying
  2. 50 %, to keep it soft in the pack
  3. 0 %, removing every trace of water
  4. 12 %
Answer and working

D. 12 %

Drying from about 30 % to about 12 % or below gives a stable product.

A study plan for Extrusion & Texturisation Technology in ICAR AICE-JRF/SRF

This plan follows where our questions actually fall, so the time goes where the marks are likely to be. It is our reading of the syllabus, not the exam body's weighting.

  1. First, the heavy units (43% of the 67 questions): Single-screw extruders: flow and pressure (8, 12%); Die design and product shaping (7, 10%); Protein texturisation: low-moisture and high-moisture extrusion (7, 10%); Starch transformations during extrusion (7, 10%).

    Read the manual chapters for these first and do every worked question you can find on them.

  2. Then the middle band: Twin-screw extruders: configuration and screw elements (7, 10%); Pasta and cold-forming extrusion (6, 9%); Quality evaluation of extrudates: expansion ratio and bulk density (6, 9%); Specific mechanical energy and process variables (6, 9%).

    Aim for one sitting per unit, then mixed questions across them.

  3. Then the lighter units: Co-extrusion and filled products (5, 7%); Expanded snacks and ready-to-eat breakfast cereals (5, 7%); Principles of extrusion cooking (3, 4%).

    Learn the definitions, classifications and standard numbers; these units are more often recalled than worked.

  4. Leave time for the hard ones: Specific mechanical energy and process variables (4 hard of 6), Protein texturisation: low-moisture and high-moisture extrusion (4 hard of 7), Starch transformations during extrusion (4 hard of 7).

    Come back to these after a first pass, untimed, and read every explanation, including for the options you rejected.

  5. Bank the easy marks: Pasta and cold-forming extrusion (2 easy of 6); Twin-screw extruders: configuration and screw elements (2 easy of 7).

    Do these early in revision so they are fast on the day.

  6. Finish timed. Sit the subject as a timed set without notes, mark it, and send each wrong answer back to its unit above.

Last updated · How Laisha writes and checks its pages · Report a mistake

Ask Laisha about this

Opens Laisha's chat with your question ready to send. Sign in or start free.

Unlock every question — ICAR AICE-JRF/SRF Extrusion & Texturisation Technology

US$10 a month · one price worldwide · cancel any time

  • Every practice question in this subject, with full working
  • Timed exam papers and progress by unit
  • Ask Laisha to explain any answer — up to 1,000 questions a month
Free or Smarter
FreeSmarter
Grow guides, pest pages, articlesRead allRead all
Ask Laisha5 a dayUp to 1,000 a month
Exam practiceThe sample on each pageEvery question, timed papers
Crop calendar and pest alerts—For your own fields
Calculators and tools—All
Uploads and reports—100 a month, real files
10 days free for every new account, no card.