LAISHA
Open Laisha

National Technical Qualification Transport Phenomena in Food Processing: Fluid Flow, Heat & Mass Transfer: practice questions

National Technical Qualification — Food Engineer (식품기사) and Food Industrial Engineer (식품산업기사) · South Korea · Human Resources Development Service of Korea (HRDK), Q-Net

Original practice questions written to the published syllabus · not past papers
10worked here, free
15written to this exam in this subject
10syllabus units

About National Technical Qualification

National Technical Qualification — Food Engineer (식품기사) and Food Industrial Engineer (식품산업기사) is a licensing and registration exam run by Human Resources Development Service of Korea (HRDK), Q-Net, for candidates in South Korea. Written examination followed by a practical examination; graded national technical qualifications.

Official site: q-net.or.kr.

We have not been able to confirm these details against the exam body's own specification, so fees, dates and pass marks are left out on purpose. Check the current format, eligibility, fees and dates on the official site.

Transport Phenomena in Food Processing: Fluid Flow, Heat & Mass Transfer in National Technical Qualification

Mass and energy balances and the three transfer processes — momentum, heat and mass — applied to foods: pumping viscous products, heating cans and pouches, and moisture and gas movement through foods and packaging films.

Our 15 National Technical Qualification questions in this subject: 1 easy, 7 medium, 7 hard, across 10 units.

10 practice questions, worked

Choose an answer, then open the working. Each explanation says why the right answer is right and why the others are not.

These 10 were written to National Technical Qualification and are not shown on any other exam's page.

Question 1 · hard

When scaling a mixing process from a 50 L pilot vessel to a 5,000 L production vessel, engineers commonly keep which quantity constant when the aim is similar turbulence intensity?

  1. Impeller tip speed only, regardless of vessel size
  2. Power input per unit volume
  3. Total motor power in kilowatts
  4. Impeller rotational speed in rpm
Answer and working

B. Power input per unit volume

Constant P/V is a common scale-up rule for turbulent mixing; constant rpm would give far higher power per volume in the large tank, and constant total power far lower.

Question 2 · hard

100 kg of carrots at 88 % moisture (wet basis) are dried to 8 % moisture (wet basis). The water removed is closest to

  1. 87.0 kg
  2. 80.0 kg
  3. 88.0 kg
  4. 81.0 kg
Answer and working

A. 87.0 kg

Solids = 12 kg; dried product = 12/0.92 = 13.04 kg; water removed = 87.0 kg. 80.0 kg subtracts percentages; 88.0 kg removes all water; 81.0 kg takes 92 % of 88 kg.

Question 3 · medium

A juice plant blends 400 kg of juice at 11 °Brix with 600 kg at 15 °Brix. The blend's °Brix is

  1. 13.4
  2. 13.0
  3. 12.6
  4. 26.0
Answer and working

A. 13.4

(400 × 11 + 600 × 15)/1,000 = (4,400 + 9,000)/1,000 = 13.4. 13.0 is the unweighted average; 12.6 swaps the masses; 26.0 adds the two Brix values.

Question 4 · medium

2,000 kg/h of milk (cp = 3.9 kJ/kg K) is heated from 10 °C to 72 °C by steam condensing at 120 °C (hfg = 2,202 kJ/kg), condensate leaving saturated. The steam needed is closest to

  1. 220 kg/h
  2. 214 kg/h
  3. 255 kg/h
  4. 56 kg/h
Answer and working

A. 220 kg/h

ṁs = 2,000 × 3.9 × 62/2,202 = 220 kg/h. 214 uses hfg at 100 °C; 255 heats from 0 °C; 56 omits cp.

Question 5 · medium

In a milk pasteuriser, raw milk at 4 °C is heated to 65 °C in the regeneration section and then to 72 °C. With equal flows, the regeneration efficiency is closest to

  1. 90 %
  2. 85 %
  3. 10 %
  4. 100 %
Answer and working

A. 90 %

(65 − 4)/(72 − 4) = 61/68 = 90 %. 85 % divides by 72 instead of 68; 10 % is the remaining heating share; 100 % would need no final heating.

Question 6 · medium

Water leaving a pipe into a tank at 1.5 m/s has an exit loss coefficient K = 1.0. The energy lost per kilogram is

  1. 1.125 J/kg
  2. 2.25 J/kg
  3. 0.75 J/kg
  4. 1.5 J/kg
Answer and working

A. 1.125 J/kg

Loss = K v²/2 = 1.0 × 2.25/2 = 1.125 J/kg. 2.25 omits the /2; 0.75 uses v/2; 1.5 uses v instead of v².

Question 7 · hard

A cooling section of a juice line underperforms. The juice-side film coefficient is about 800 W/m² K and the water side about 5,000 W/m² K. The most effective way to raise the overall coefficient is to

  1. increase juice-side turbulence
  2. increase cooling-water velocity further
  3. replace stainless steel with a thinner stainless sheet
  4. raise the cooling-water temperature
Answer and working

A. increase juice-side turbulence

The smaller film coefficient controls U; improving the juice side helps most. Raising water temperature reduces the driving force.

Question 8 · medium

Milk is heated from 10 °C to 60 °C by hot water cooling from 80 °C to 40 °C in counter-current flow. The LMTD is closest to

  1. 25.0 K
  2. 24.5 K
  3. 40.0 K
  4. 24.7 K
Answer and working

D. 24.7 K

ΔT1 = 80 − 60 = 20 K, ΔT2 = 40 − 10 = 30 K; LMTD = 10/ln 1.5 = 24.7 K. 25.0 K is the arithmetic mean; 24.5 K is the geometric mean √(20 × 30); 40.0 K uses inlet-to-inlet difference.

Question 9 · hard

During a long run, a milk heater's outlet temperature falls although steam supply is unchanged. The most likely cause is

  1. a rise in the latent heat of the steam supply during the run
  2. the milk becoming less viscous as it warms
  3. the LMTD increasing as the run continues
  4. fouling deposits adding resistance and lowering U
Answer and working

D. fouling deposits adding resistance and lowering U

Protein and mineral fouling builds up resistance; plants clean on a schedule or when temperature or pressure drop limits are reached.

Question 10 · medium

Carcass weight loss during chilling can be reduced by

  1. raising air velocity and lowering the humidity throughout the whole chilling period
  2. lowering air velocity and raising humidity once the surface is cool
  3. heating the carcass surface to dry it quickly
  4. spraying the carcass with oil before chilling
Answer and working

B. lowering air velocity and raising humidity once the surface is cool

Evaporation rate rises with km (air velocity) and the vapour-concentration difference; spray chilling and humid air reduce it.

A study plan for Transport Phenomena in Food Processing: Fluid Flow, Heat & Mass Transfer in National Technical Qualification

This plan follows where our questions actually fall, so the time goes where the marks are likely to be. It is our reading of the syllabus, not the exam body's weighting.

  1. First, the heavy units (60% of the 15 questions): Energy balances and steam tables (3, 20%); Heat exchangers: plate, tubular and scraped-surface; LMTD and effectiveness (3, 20%); Material balances on mixing, concentration and drying (2, 13%); Convection: film coefficients and dimensionless numbers (1, 7%).

    Read the manual chapters for these first and do every worked question you can find on them.

  2. Then the middle band: Convective mass transfer (1, 7%); Flow in pipes: Reynolds number, friction factor and pressure drop for Newtonian fluids (1, 7%); Flow of non-Newtonian foods in pipes (1, 7%); Pumps for foods: centrifugal and positive-displacement (1, 7%).

    Aim for one sitting per unit, then mixed questions across them.

  3. Then the lighter units: Steady-state conduction through slabs, cylinders and composite walls (1, 7%); Units, dimensions and dimensional analysis (1, 7%).

    Learn the definitions, classifications and standard numbers; these units are more often recalled than worked.

  4. Leave time for the hard ones: Convection: film coefficients and dimensionless numbers (1 hard of 1), Flow of non-Newtonian foods in pipes (1 hard of 1), Units, dimensions and dimensional analysis (1 hard of 1).

    Come back to these after a first pass, untimed, and read every explanation, including for the options you rejected.

  5. Bank the easy marks: Pumps for foods: centrifugal and positive-displacement (1 easy of 1).

    Do these early in revision so they are fast on the day.

  6. Finish timed. Sit the subject as a timed set without notes, mark it, and send each wrong answer back to its unit above.

Last updated · How Laisha writes and checks its pages · Report a mistake

Ask Laisha about this

Opens Laisha's chat with your question ready to send. Sign in or start free.

Unlock every question — National Technical Qualification Transport Phenomena in Food Processing: Fluid Flow, Heat

US$10 a month · one price worldwide · cancel any time

  • Every practice question in this subject, with full working
  • Timed exam papers and progress by unit
  • Ask Laisha to explain any answer — up to 1,000 questions a month
Free or Smarter
FreeSmarter
Grow guides, pest pages, articlesRead allRead all
Ask Laisha5 a dayUp to 1,000 a month
Exam practiceThe sample on each pageEvery question, timed papers
Crop calendar and pest alerts—For your own fields
Calculators and tools—All
Uploads and reports—100 a month, real files
10 days free for every new account, no card.