LAISHA
Open Laisha

GATE ST Statistical Quality Control & Reliability: practice questions

GATE - Statistics (ST) · India · IITs and IISc on rotation (2027: IIT Madras)

Original practice questions written to the published syllabus · not past papers
10worked here, free
40written to this exam in this subject
10syllabus units

About GATE ST

GATE - Statistics (ST) is a postgraduate admission exam run by IITs and IISc on rotation (2027: IIT Madras), for candidates in India. Computer-based, 3 hours, 100 marks (15 General Aptitude + 85 subject). MCQ, MSQ and NAT; negative marking on MCQ only; on-screen virtual calculator.

Source: gate2026.iitg.ac.in.

Checked against the exam body's published information. Formats and fees change; confirm the current edition there before you book.

Statistical Quality Control & Reliability in GATE ST

Monitoring and accepting quality: Shewhart charts for variables and attributes, CUSUM and EWMA charts, process capability, acceptance sampling plans with their OC, AOQ and ATI curves, and reliability models, applied to seed testing, food processing and input quality. The Agricultural Engineering track covers control charts briefly; this is the full subject.

Our 40 GATE ST questions in this subject: 6 easy, 28 medium, 6 hard, across 10 units.

10 practice questions, worked

Choose an answer, then open the working. Each explanation says why the right answer is right and why the others are not.

These 10 were written to GATE ST and are not shown on any other exam's page.

Question 1 · medium

A tabular CUSUM has μ₀ = 500 g, K = 1 g and H = 10 g. Observations are 501, 503, 502, 504, 503, 504. When does C⁺ first exceed H?

  1. At the 4th observation, C⁺ = 6
  2. Never in these data
  3. At the 6th observation, C⁺ = 11
  4. At the 5th observation, C⁺ = 8
Answer and working

C. At the 6th observation, C⁺ = 11

C⁺ = max(0, x − 501 + C⁺₋₁): 0, 2, 3, 6, 8, 11, so the signal comes at the 6th value.

Question 2 · medium

A centred normal process has Cp = 1. What fraction falls outside specifications?

  1. About 0.0063%
  2. Exactly 0
  3. About 5%
  4. About 0.27%
Answer and working

D. About 0.27%

Limits are at μ ± 3σ, so 2[1 − Φ(3)] = 0.0027 (2,700 ppm); 0.0063% is about Cp = 1.33.

Question 3 · medium

A filler's σ is halved from 8 g to 4 g. Keeping the same protection against under-weight packs, by about how much can the mean fill be lowered with a 3σ margin?

  1. 4 g
  2. 24 g
  3. 8 g
  4. 12 g
Answer and working

D. 12 g

The margin above the lower limit falls from 3 × 8 = 24 g to 3 × 4 = 12 g, saving 12 g of give-away per pack.

Question 4 · easy

What is the main advantage of variables sampling over attribute sampling?

  1. One plan covers all characteristics
  2. Smaller samples
  3. No distributional assumption
  4. It never rejects conforming lots
Answer and working

B. Smaller samples

Measurements carry more information than pass/fail records, so fewer items are needed.

Question 5 · medium

Where does the Six Sigma figure of 3.4 defects per million come from?

  1. A 3σ margin with no shift
  2. A 4.5σ margin with a 1.5σ shift
  3. A 6σ margin with no shift
  4. 6σ margin less a 1.5σ shift
Answer and working

D. 6σ margin less a 1.5σ shift

With a 1.5σ shift the nearest limit is 4.5σ away: 1 − Φ(4.5) ≈ 3.4e-06, i.e. 3.4 per million; without the shift the rate is about 0.002 ppm.

Question 6 · hard

Under Taguchi's loss L = k(y − T)², what is the expected loss?

  1. k[σ² + (μ − T)²]
  2. k|μ − T|
  3. kσ²
  4. k(μ − T)²
Answer and working

A. k[σ² + (μ − T)²]

E(y − T)² = Var(y) + (μ − T)², so both variability and off-target mean cost.

Question 7 · medium

A Weibull life has shape 2 and characteristic life 1,000 h. What is R(500 h)?

  1. 0.607
  2. 0.221
  3. 0.500
  4. 0.779
Answer and working

D. 0.779

R(t) = exp[−(t/η)^β] = exp(−0.25) = 0.779; an exponential with the same η gives e^(−0.5) = 0.607.

Question 8 · medium

The average number of defects per unit is c̄ = 9. The upper control limit of the c chart is:

  1. 18
  2. 27
  3. 12
  4. 15
Answer and working

A. 18

For Poisson counts the variance equals the mean, so UCL = c̄ + 3√c̄ = 9 + 3 × 3 = 18 and LCL = 9 − 9 = 0.

Question 9 · medium

Two independent components each with reliability 0.9 are connected in parallel. The system reliability is:

  1. 0.81
  2. 0.90
  3. 0.99
  4. 0.95
Answer and working

C. 0.99

A parallel system fails only if both fail: R = 1 − (1 − 0.9)² = 1 − 0.01 = 0.99. In series it would be 0.9 × 0.9 = 0.81.

Question 10 · hard

A component has lifetime with hazard rate h(t) = 2t (t ≥ 0). Its reliability at t = 1 is:

  1. e^{−2}
  2. e^{−1}
  3. 1 − e^{−1}
  4. e^{−1/2}
Answer and working

B. e^{−1}

R(t) = exp[−∫0^t h(u) du] = exp(−t²), so R(1) = e^{−1} ≈ 0.368. This is a Weibull lifetime with shape 2: an increasing hazard, as in wear-out.

A study plan for Statistical Quality Control & Reliability in GATE ST

This plan follows where our questions actually fall, so the time goes where the marks are likely to be. It is our reading of the syllabus, not the exam body's weighting.

  1. First, the heavy units (57% of the 40 questions): Reliability: hazard rate, series and parallel systems, life testing (7, 18%); CUSUM and EWMA charts (6, 15%); Acceptance sampling by variables (5, 13%); Control charts for variables: X-bar, R and s charts (5, 13%).

    Read the manual chapters for these first and do every worked question you can find on them.

  2. Then the middle band: Process capability indices (4, 10%); Six Sigma and design for quality (introduction) (4, 10%); Chance and assignable causes of variation (3, 8%); Control charts for attributes: p, np, c and u charts (3, 8%).

    Aim for one sitting per unit, then mixed questions across them.

  3. Then the lighter units: Acceptance sampling by attributes: single, double and sequential plans (2, 5%); OC, AOQ, AOQL, ASN and ATI curves (1, 3%).

    Learn the definitions, classifications and standard numbers; these units are more often recalled than worked.

  4. Leave time for the hard ones: Acceptance sampling by attributes: single, double and sequential plans (1 hard of 2), Reliability: hazard rate, series and parallel systems, life testing (3 hard of 7), Six Sigma and design for quality (introduction) (1 hard of 4).

    Come back to these after a first pass, untimed, and read every explanation, including for the options you rejected.

  5. Bank the easy marks: CUSUM and EWMA charts (2 easy of 6); Process capability indices (1 easy of 4).

    Do these early in revision so they are fast on the day.

  6. Finish timed. Sit the subject as a timed set without notes, mark it, and send each wrong answer back to its unit above.

Last updated · How Laisha writes and checks its pages · Report a mistake

Ask Laisha about this

Opens Laisha's chat with your question ready to send. Sign in or start free.

Unlock every question — GATE ST Statistical Quality Control & Reliability

US$10 a month · one price worldwide · cancel any time

  • Every practice question in this subject, with full working
  • Timed exam papers and progress by unit
  • Ask Laisha to explain any answer — up to 1,000 questions a month
Free or Smarter
FreeSmarter
Grow guides, pest pages, articlesRead allRead all
Ask Laisha5 a dayUp to 1,000 a month
Exam practiceThe sample on each pageEvery question, timed papers
Crop calendar and pest alerts—For your own fields
Calculators and tools—All
Uploads and reports—100 a month, real files
10 days free for every new account, no card.