ICAR AIEEA-PG: Dairy Science (group 16) and Dairy Technology (group 17) · India · NTA for ICAR
Original practice questions written to the published syllabus · not past papersICAR AIEEA-PG: Dairy Science (group 16) and Dairy Technology (group 17) is a postgraduate admission exam run by NTA for ICAR, for candidates in India. Computer-based, 2 hours, 120 multiple-choice questions, +4 for a correct answer and −1 for a wrong one (2026 bulletin). One paper per major subject group.
Source: icar.org.in.
Checked against the exam body's published information. Formats and fees change; confirm the current edition there before you book.
The calculus, differential equations and statistics that dairy engineering problems, kinetics and quality control need.
Our 42 ICAR AIEEA-PG questions in this subject: 6 easy, 32 medium, 4 hard, across 9 units.
Choose an answer, then open the working. Each explanation says why the right answer is right and why the others are not.
These 10 were written to ICAR AIEEA-PG and are not shown on any other exam's page.
A pasteuriser holding tube is designed with milk in laminar flow at a mean velocity of 0.5 m/s. At what velocity must the fastest particle be assumed to travel when checking the minimum holding time?
B. 1.0 m/s
In laminar flow u_max = 2 × mean = 1.0 m/s, and the fastest particle receives the shortest holding time. 0.61 m/s corresponds to the turbulent ratio (mean ≈ 0.82 u_max); using the mean 0.5 m/s overestimates the holding time.
In thermal process calculation, the F value of a process is obtained by:
A. Integrating the lethal rate 10^((T − T_ref)/z) over the heating time
F = ∫10^((T − T_ref)/z) dt accumulates lethality minute by minute. Peak temperature × time ignores that lethality rises tenfold for each z degrees.
Vitamin C in a flavoured milk is lost by first-order kinetics with k = 0.05 per day. What is its half-life?
A. 13.9 days
t½ = ln 2/k = 0.693/0.05 = 13.9 days. 1/k = 20 days is the time constant; 2.303/k = 46.1 days is the time for a tenfold fall (the D value).
Newton's law of cooling, applied as a lumped-capacity model, is reasonable when the Biot number is:
A. Below about 0.1
Bi = hL/k_solid compares internal to surface resistance. Below about 0.1 the internal temperature is nearly uniform, so a single temperature describes the body. Large blocks of butter or cheese have high Bi and need conduction models.
A well-mixed 2,000 litre balance tank is flushed with clean water at 500 litres per minute. What fraction of an initial dissolved residue remains after 12 minutes?
A. 0.050
τ = V/q = 2000/500 = 4 min. C/C₀ = e^(−t/τ) = e^(−3) = 0.050. Plug-flow thinking (three tank volumes = empty) gives 0; e^(−4/12) inverts the ratio.
Applying one Newton–Raphson step to f(x) = x³ − 2x − 5 from x₀ = 2 gives:
C. 2.1
f(2) = 8 − 4 − 5 = −1; f′(x) = 3x² − 2, so f′(2) = 10. x₁ = 2 − (−1)/10 = 2.1. Sign slips give 1.9.
Which statement correctly interprets a 95% confidence interval of 3.42 to 3.58% for the mean fat of a silo?
A. 95% of intervals built this way, over repeated sampling, contain the true mean
The 95% describes the long-run success of the method. The interval concerns the mean, not individual samples, which spread far more widely.
A sample is drawn from the top of an unstirred milk tank. The resulting error in fat content is best described as:
C. A non-sampling bias error that more replicate samples from the top would not reduce
Cream rises in unstirred milk, so top samples are systematically high in fat. That is bias, which more samples from the same spot do not remove; only mixing does.
A calibration line is A = 0.016 + 0.196C (C in mg/L). A sample reads A = 0.50. What is its concentration?
C. 2.47 mg/L
C = (A − a)/b = (0.50 − 0.016)/0.196 = 2.47 mg/L. Ignoring the intercept gives 2.55; adding it gives 2.63.
Response surface methodology is used in dairy product development mainly to:
A. Find factor settings that optimise a curved response with interacting factors
RSM fits a model (usually quadratic) to designed experiments and locates optimum factor levels.
This plan follows where our questions actually fall, so the time goes where the marks are likely to be. It is our reading of the syllabus, not the exam body's weighting.
Read the manual chapters for these first and do every worked question you can find on them.
Aim for one sitting per unit, then mixed questions across them.
Learn the definitions, classifications and standard numbers; these units are more often recalled than worked.
Come back to these after a first pass, untimed, and read every explanation, including for the options you rejected.
Do these early in revision so they are fast on the day.
Last updated · How Laisha writes and checks its pages · Report a mistake
US$10 a month · one price worldwide · cancel any time
| Free | Smarter | |
|---|---|---|
| Grow guides, pest pages, articles | Read all | Read all |
| Ask Laisha | 5 a day | Up to 1,000 a month |
| Exam practice | The sample on each page | Every question, timed papers |
| Crop calendar and pest alerts | — | For your own fields |
| Calculators and tools | — | All |
| Uploads and reports | — | 100 a month, real files |
An AI operating system for agriculture: free guides, manuals and tools written for every country.