LAISHA
Open Laisha

Indian Forest Service Examination Wood Products & Forest-Based Industries: practice questions

Indian Forest Service Examination (IFoS) — Forestry optional · India · Union Public Service Commission

Original practice questions written to the published syllabus · not past papers
10worked here, free
39written to this exam in this subject
10syllabus units

About Indian Forest Service Examination

Indian Forest Service Examination (IFoS) — Forestry optional is a government recruitment exam run by Union Public Service Commission, for candidates in India. Three stages: the Civil Services (Preliminary) Examination as a screening test; a written Main examination of six conventional papers (General English 300, General Knowledge 300, and two optional subjects of two papers each at 200 marks, 1,400 in all); and a 300-mark personality test.

Official site: upsc.gov.in.

We have not been able to confirm these details against the exam body's own specification, so fees, dates and pass marks are left out on purpose. Check the current format, eligibility, fees and dates on the official site.

Wood Products & Forest-Based Industries in Indian Forest Service Examination

Turning wood into products: sawmilling, veneer and plywood, panels and engineered wood, pulp and paper, wood energy and the chemistry of wood-based industries.

Our 39 Indian Forest Service Examination questions in this subject: 8 easy, 21 medium, 10 hard, across 10 units.

10 practice questions, worked

Choose an answer, then open the working. Each explanation says why the right answer is right and why the others are not.

These 10 were written to Indian Forest Service Examination and are not shown on any other exam's page.

Question 1 · medium

Quarter-sawn boards, compared with flat-sawn boards:

  1. Shrink more in width and cup more
  2. Have lower recovery and no figure in any species
  3. Shrink less in width and cup less
  4. Cannot be dried in kilns
Answer and working

C. Shrink less in width and cup less

Faces are radial; recovery is lower and sawing slower.

Question 2 · hard

Why is saw maintenance by a saw doctor important for recovery?

  1. It increases the diameter of the logs delivered
  2. It adds preservative to every board sawn
  3. It reduces the need for grading the output
  4. Straighter, thinner cuts
Answer and working

D. Straighter, thinner cuts

Accurate sawing needs less oversize and planing allowance.

Question 3 · medium

Phenol-formaldehyde adhesives are used for:

  1. Interior plywood only, kept dry
  2. Paper sizing
  3. Pellet binding
  4. Exterior and marine plywood
Answer and working

D. Exterior and marine plywood

PF bonds resist boiling water; UF is for interior use.

Question 4 · hard

Reconstituted panels are important for forest use mainly because they:

  1. Use thinnings, residues and recycled wood
  2. Require large, clear, high-grade logs
  3. Need durable species
  4. Use only bamboo
Answer and working

A. Use thinnings, residues and recycled wood

Small and low-grade material becomes useful panels.

Question 5 · easy

Softwood fibres are commonly about how long?

  1. 0.3 mm
  2. 3 mm
  3. 30 mm
  4. 3 cm
Answer and working

B. 3 mm

Hardwood fibres are about 1 mm.

Question 6 · easy

Oven-dry wood has a net calorific value of 19 MJ/kg. Using NCV(wet) = NCV(dry)(1 − w) − 2.44w, what is the net value at 30% wet-basis moisture?

  1. 13.3 MJ/kg
  2. 12.6 MJ/kg
  3. 19.0 MJ/kg
  4. 5.7 MJ/kg
Answer and working

B. 12.6 MJ/kg

19 × 0.7 − 2.44 × 0.3 = 13.3 − 0.73 = 12.6 MJ/kg. 13.3 ignores evaporation energy.

Question 7 · hard

The forest biorefinery concept aims to:

  1. Burning all wood for electricity generation
  2. Producing only paper from all inputs
  3. Using every wood component
  4. Avoiding any chemical processing of wood
Answer and working

C. Using every wood component

Like an oil refinery using all fractions of crude.

Question 8 · medium

In India, the code of practice for design of structural timber is:

  1. IS 303
  2. IS 401
  3. IS 710
  4. IS 883
Answer and working

D. IS 883

The National Building Code 2016 also covers timber and bamboo.

Question 9 · medium

Timber should be dried before installation in buildings mainly to:

  1. Increase its weight for stability
  2. Make it combustible
  3. Limit movement after installation
  4. Change its species
Answer and working

C. Limit movement after installation

Drying to service MC prevents shrinkage gaps and distortion.

Question 10 · medium

Which tool quantifies the environmental impacts of building materials over their life?

  1. Life-cycle assessment
  2. Bucking optimisation software
  3. Prong test
  4. Janka test
Answer and working

A. Life-cycle assessment

LCA and environmental product declarations compare materials.

A study plan for Wood Products & Forest-Based Industries in Indian Forest Service Examination

This plan follows where our questions actually fall, so the time goes where the marks are likely to be. It is our reading of the syllabus, not the exam body's weighting.

  1. First, the heavy units (44% of the 39 questions): Wood energy: fuelwood, charcoal, pellets (5, 13%); Engineered wood: glulam, LVL, cross-laminated timber (4, 10%); Particleboard, fibreboard (MDF) and oriented strand board (4, 10%); Pulp and paper: raw materials, pulping processes (4, 10%).

    Read the manual chapters for these first and do every worked question you can find on them.

  2. Then the middle band: Timber in construction and its standards (4, 10%); Veneer and plywood manufacture (4, 10%); Wood chemistry and extractives (4, 10%); Wood-based industries: raw-material supply and residues (4, 10%).

    Aim for one sitting per unit, then mixed questions across them.

  3. Then the lighter units: Chain of custody and legality in wood supply (3, 8%); Sawmilling and recovery (3, 8%).

    Learn the definitions, classifications and standard numbers; these units are more often recalled than worked.

  4. Leave time for the hard ones: Chain of custody and legality in wood supply (1 hard of 3), Sawmilling and recovery (1 hard of 3), Engineered wood: glulam, LVL, cross-laminated timber (1 hard of 4).

    Come back to these after a first pass, untimed, and read every explanation, including for the options you rejected.

  5. Bank the easy marks: Particleboard, fibreboard (MDF) and oriented strand board (2 easy of 4); Pulp and paper: raw materials, pulping processes (2 easy of 4).

    Do these early in revision so they are fast on the day.

  6. Finish timed. Sit the subject as a timed set without notes, mark it, and send each wrong answer back to its unit above.

Last updated · How Laisha writes and checks its pages · Report a mistake

Ask Laisha about this

Opens Laisha's chat with your question ready to send. Sign in or start free.

Unlock every question — Indian Forest Service Examination Wood Products & Forest-Based Industries

US$10 a month · one price worldwide · cancel any time

  • Every practice question in this subject, with full working
  • Timed exam papers and progress by unit
  • Ask Laisha to explain any answer — up to 1,000 questions a month
Free or Smarter
FreeSmarter
Grow guides, pest pages, articlesRead allRead all
Ask Laisha5 a dayUp to 1,000 a month
Exam practiceThe sample on each pageEvery question, timed papers
Crop calendar and pest alerts—For your own fields
Calculators and tools—All
Uploads and reports—100 a month, real files
10 days free for every new account, no card.