LAISHA
Open Laisha

ICAR AICE-JRF/SRF Advanced Dairy Engineering: practice questions

ICAR AICE-JRF/SRF (PhD): Dairy Chemistry, Dairy Microbiology, Dairy Technology, Dairy Engineering · India · NTA for ICAR

Original practice questions written to the published syllabus · not past papers
10worked here, free
100written to this exam in this subject
10syllabus units

About ICAR AICE-JRF/SRF

ICAR AICE-JRF/SRF (PhD): Dairy Chemistry, Dairy Microbiology, Dairy Technology, Dairy Engineering is a PhD, fellowship and lectureship exam run by NTA for ICAR, for candidates in India.

Source: icar.org.in.

Checked against the exam body's published information. Formats and fees change; confirm the current edition there before you book.

Advanced Dairy Engineering in ICAR AICE-JRF/SRF

Graduate-level transport phenomena, process modelling, design and simulation for dairy processes, as examined in ICAR AICE subject 38.

Our 100 ICAR AICE-JRF/SRF questions in this subject: 2 easy, 80 medium, 18 hard, across 10 units.

10 practice questions, worked

Choose an answer, then open the working. Each explanation says why the right answer is right and why the others are not.

These 10 were written to ICAR AICE-JRF/SRF and are not shown on any other exam's page.

Question 1 · medium

The Chilton–Colburn analogy states that:

  1. Nu = 0.023 Re^0.8 Pr^0.4 for every geometry and flow regime
  2. Sh = 2 for all spheres (stagnant fluid limit)
  3. f = 64/Re in turbulent flow
  4. j_H = St Pr^(2/3) = f/2
Answer and working

D. j_H = St Pr^(2/3) = f/2

It extends Reynolds' analogy to Pr and Sc different from one, linking friction to heat and mass transfer.

Question 2 · hard

A soft sensor for milk powder moisture in a dryer is usually based on:

  1. Visual inspection of the powder colour by operators each hour
  2. Feed fat content alone
  3. Ambient noise
  4. Calibrated heat and mass balances
Answer and working

D. Calibrated heat and mass balances

Exhaust humidity, temperatures and flows estimate moisture continuously.

Question 3 · hard

A key limitation of current spray dryer CFD is:

  1. Agglomeration and collisions
  2. An inability to model air flow at all inside large chambers
  3. Ignoring gravity
  4. Requiring no validation
Answer and working

A. Agglomeration and collisions

Agglomeration, fines return and drying kinetics remain uncertain and costly to model.

Question 4 · hard

Microwave tempering of frozen dairy blocks risks runaway heating because:

  1. Ice absorbs microwaves more strongly than water
  2. Liquid water absorbs microwaves more than ice
  3. Fat freezes faster than water
  4. Microwaves cool the surface
Answer and working

B. Liquid water absorbs microwaves more than ice

Thawed regions absorb more energy and heat faster, causing hot spots.

Question 5 · medium

A major difficulty when simulating dairy plants in general chemical simulators is:

  1. A complete lack of unit operations such as heat exchangers and pumps
  2. Inability to calculate mass balances
  3. Missing dairy property data
  4. No support for water as a component
Answer and working

C. Missing dairy property data

Users define pseudo-components and property correlations from dairy literature.

Question 6 · medium

A digital twin is a model that is:

  1. Continuously updated with plant data
  2. A copy of the plant built in another country
  3. A static design drawing
  4. A spreadsheet of costs only
Answer and working

A. Continuously updated with plant data

Data reconciliation and parameter estimation keep the model aligned with the plant.

Question 7 · medium

Data reconciliation in a digital twin:

  1. Deletes all measurements that disagree with the design values
  2. Adds fictitious streams to hide errors
  3. Ignores sensor uncertainty completely
  4. Adjusts data to close balances
Answer and working

D. Adjusts data to close balances

Measurements are corrected statistically so mass and energy balances close.

Question 8 · medium

Thin-walled evaporator bodies under vacuum must be designed mainly against:

  1. Internal bursting at high pressure
  2. Creep at 500 °C
  3. Hydrogen embrittlement
  4. Buckling
Answer and working

D. Buckling

External pressure causes buckling; stiffening rings shorten the effective length.

Question 9 · hard

Why must pasteurisation flow diversion not depend on a machine-learning model?

  1. Safety functions need simple, validated logic
  2. Machine learning cannot read temperature signals from sensors
  3. Regulators ban computers in dairies
  4. Models are too slow for any purpose
Answer and working

A. Safety functions need simple, validated logic

Protective functions stay in independent systems; advanced methods optimise within them.

Question 10 · medium

In dairy product life-cycle assessments, the largest share of emissions usually comes from:

  1. Processing electricity
  2. On-farm emissions
  3. Packaging
  4. Retail lighting
Answer and working

B. On-farm emissions

Enteric methane, manure and feed dominate; powders have larger processing shares.

A study plan for Advanced Dairy Engineering in ICAR AICE-JRF/SRF

This plan follows where our questions actually fall, so the time goes where the marks are likely to be. It is our reading of the syllabus, not the exam body's weighting.

  1. First, the heavy units (40% of the 100 questions): Advanced control and machine learning in dairy plants (10, 10%); Fouling models and cleaning optimisation (10, 10%); Freezing and thawing models (10, 10%); Membrane process modelling (10, 10%).

    Read the manual chapters for these first and do every worked question you can find on them.

  2. Then the middle band: Modelling of heat treatment and lethality (10, 10%); Pressure vessel and heat exchanger design codes (10, 10%); Process simulation software (10, 10%); Spray dryer modelling and computational fluid dynamics (10, 10%).

    Aim for one sitting per unit, then mixed questions across them.

  3. Then the lighter units: Sustainability engineering: energy and water pinch analysis (10, 10%); Transport phenomena in dairy processes (10, 10%).

    Learn the definitions, classifications and standard numbers; these units are more often recalled than worked.

  4. Leave time for the hard ones: Modelling of heat treatment and lethality (3 hard of 10), Advanced control and machine learning in dairy plants (2 hard of 10), Fouling models and cleaning optimisation (2 hard of 10).

    Come back to these after a first pass, untimed, and read every explanation, including for the options you rejected.

  5. Bank the easy marks: Spray dryer modelling and computational fluid dynamics (1 easy of 10); Transport phenomena in dairy processes (1 easy of 10).

    Do these early in revision so they are fast on the day.

  6. Finish timed. Sit the subject as a timed set without notes, mark it, and send each wrong answer back to its unit above.

Last updated · How Laisha writes and checks its pages · Report a mistake

Ask Laisha about this

Opens Laisha's chat with your question ready to send. Sign in or start free.

Unlock every question — ICAR AICE-JRF/SRF Advanced Dairy Engineering

US$10 a month · one price worldwide · cancel any time

  • Every practice question in this subject, with full working
  • Timed exam papers and progress by unit
  • Ask Laisha to explain any answer — up to 1,000 questions a month
Free or Smarter
FreeSmarter
Grow guides, pest pages, articlesRead allRead all
Ask Laisha5 a dayUp to 1,000 a month
Exam practiceThe sample on each pageEvery question, timed papers
Crop calendar and pest alerts—For your own fields
Calculators and tools—All
Uploads and reports—100 a month, real files
10 days free for every new account, no card.