LAISHA
Open Laisha

ICAR AICE-JRF/SRF Rheology & Texture of Dairy Foods: practice questions

ICAR AICE-JRF/SRF (PhD): Dairy Chemistry, Dairy Microbiology, Dairy Technology, Dairy Engineering · India · NTA for ICAR

Original practice questions written to the published syllabus · not past papers
10worked here, free
109written to this exam in this subject
11syllabus units

About ICAR AICE-JRF/SRF

ICAR AICE-JRF/SRF (PhD): Dairy Chemistry, Dairy Microbiology, Dairy Technology, Dairy Engineering is a PhD, fellowship and lectureship exam run by NTA for ICAR, for candidates in India.

Source: icar.org.in.

Checked against the exam body's published information. Formats and fees change; confirm the current edition there before you book.

Rheology & Texture of Dairy Foods in ICAR AICE-JRF/SRF

Flow and deformation of milk, cream, yoghurt, cheese, butter and ice cream, and how instruments measure texture.

Our 109 ICAR AICE-JRF/SRF questions in this subject: 31 easy, 50 medium, 28 hard, across 11 units.

10 practice questions, worked

Choose an answer, then open the working. Each explanation says why the right answer is right and why the others are not.

These 10 were written to ICAR AICE-JRF/SRF and are not shown on any other exam's page.

Question 1 · medium

In an up-and-down shear-rate loop on a stirred yoghurt, what indicates thixotropy?

  1. The down-curve lies above the up-curve
  2. The down-curve lies below the up-curve
  3. The two curves coincide exactly at every shear rate
  4. The flow curve passes through the origin
Answer and working

B. The down-curve lies below the up-curve

Structure broken on the way up gives lower stress on the way down, so the down-curve lies below and encloses a hysteresis area. A down-curve above the up-curve indicates rheopexy; coincident curves mean no time dependence; passing through the origin only shows there is no yield stress.

Question 2 · hard

For a power-law fluid with n = 0.5 in a tube viscometer, the Rabinowitsch-Mooney correction multiplies the apparent (Newtonian) wall shear rate by (3n + 1)/(4n). What is the factor?

  1. 1.25
  2. 0.80
  3. 1.00
  4. 0.625
Answer and working

A. 1.25

(3 × 0.5 + 1)/(4 × 0.5) = 2.5/2 = 1.25: the true wall shear rate is higher than 4Q/(πR³) for a shear-thinning fluid. 0.80 inverts the factor; 1.00 applies only when n = 1; 0.625 omits n in the denominator.

Question 3 · medium

A plant's QC laboratory reports yoghurt viscosity with a single-spindle rotational viscometer. What must accompany each reading for it to be meaningful?

  1. Only the temperature of the sample
  2. The yoghurt's fat and protein contents
  3. Spindle, speed, temperature, time and sample handling
  4. The cone angle and the gap at the tip
Answer and working

C. Spindle, speed, temperature, time and sample handling

A single-point spindle reading is an apparent viscosity whose value depends on spindle geometry, speed, temperature, reading time and how the sample was stirred. Temperature alone is not enough; composition does not define the test; cone angle and gap apply to cone-and-plate instruments.

Question 4 · medium

Why are creep and relaxation tests on dairy gels run at small deformation?

  1. To make the test finish in less time
  2. To stay within the linear viscoelastic region
  3. Because large stresses melt the fat phase
  4. To make the gel behave as a Newtonian fluid
Answer and working

B. To stay within the linear viscoelastic region

Inside the linear region the response is proportional to load and describes the intact material; larger deformations break bonds so results reflect damage. Small deformation does not shorten the test, does not affect fat melting, and does not turn a gel Newtonian.

Question 5 · medium

During a heating sweep, a cheese's tan δ rises from 0.3 at 20 °C to 1.2 at 70 °C. What has happened?

  1. It has become more elastic on heating
  2. It has changed from solid-like to liquid-like as it melted
  3. It has entered the shear-thickening region
  4. It has lost moisture and become brittle
Answer and working

B. It has changed from solid-like to liquid-like as it melted

tan δ above 1 means viscous response dominates, so the cheese has softened and begun to flow as fat melted and the protein network loosened. More elasticity would lower tan δ; shear-thickening is a steady-shear property; drying would stiffen, not liquefy, the cheese.

Question 6 · medium

Butter softens noticeably when worked and partly regains firmness on standing. What is this called?

  1. Work softening
  2. Rheopexy
  3. Syneresis
  4. Cold agglutination
Answer and working

A. Work softening

Working breaks bonds in the fat crystal network, and some re-form at rest: work softening. Rheopexy is thickening under shear; syneresis is whey expulsion; cold agglutination is clustering of fat globules in cold raw milk.

Question 7 · medium

Why is high-methoxyl pectin used in acidified milk drinks?

  1. It adsorbs to casein and prevents aggregation at low pH
  2. It forms a gel with calcium at neutral pH
  3. It lowers the viscosity of the drink to that of water
  4. It raises the pH to near neutral during storage
Answer and working

A. It adsorbs to casein and prevents aggregation at low pH

At acid pH the negatively charged pectin adsorbs onto positively charged casein and keeps particles apart by steric and charge repulsion, preventing sedimentation. Calcium gelling is a low-methoxyl pectin property; pectin raises rather than lowers viscosity; it does not change pH.

Question 8 · medium

How does homogenisation of yoghurt milk change gel firmness?

  1. It reduces firmness by removing casein from the milk
  2. It has no effect because fat is outside the gel
  3. It increases firmness, as protein-coated globules join the network
  4. It reduces firmness by raising the pH at gelation
Answer and working

C. It increases firmness, as protein-coated globules join the network

Homogenised globules are coated with casein and whey protein and behave as active network particles. Casein is redistributed, not removed; fat does take part once coated; homogenisation does not change gelation pH.

Question 9 · easy

Perceived firmness of cheese on the first bite is most closely related to which instrumental measure?

  1. Compression hardness or fracture stress
  2. Kinematic viscosity of the whey
  3. Loss tangent of the cheese after melting
  4. Springiness alone
Answer and working

A. Compression hardness or fracture stress

First-bite firmness relates to the force needed to deform and fracture the sample. Whey viscosity and melt tan δ describe other states; springiness measures recovery, not firmness.

Question 10 · medium

In an oscillatory test, the stress of a purely viscous liquid is out of phase with the strain by:

  1. 90°
  2. 0°
  3. 45°
  4. 180°
Answer and working

A. 90°

Stress in a viscous liquid follows strain rate, which leads strain by 90°. 0° is a pure elastic solid; 45° is a material with equal G′ and G″; 180° does not occur in a passive material.

A study plan for Rheology & Texture of Dairy Foods in ICAR AICE-JRF/SRF

This plan follows where our questions actually fall, so the time goes where the marks are likely to be. It is our reading of the syllabus, not the exam body's weighting.

  1. First, the heavy units (39% of the 109 questions): Newtonian and non-Newtonian fluids; power-law and Herschel-Bulkley models (12, 11%); Dynamic oscillatory measurements (10, 9%); Effect of processing and stabilisers on rheology (10, 9%); Mechanical models: Maxwell, Kelvin-Voigt and Burgers (10, 9%).

    Read the manual chapters for these first and do every worked question you can find on them.

  2. Then the middle band: Rheology of cheese, butter, yoghurt and ice cream (10, 9%); Stress, strain and rheological classification (10, 9%); Texture profile analysis (10, 9%); Viscometers and rheometers (10, 9%).

    Aim for one sitting per unit, then mixed questions across them.

  3. Then the lighter units: Large deformation and fracture (9, 8%); Relating instrumental and sensory texture (9, 8%); Viscoelasticity: creep and stress relaxation (9, 8%).

    Learn the definitions, classifications and standard numbers; these units are more often recalled than worked.

  4. Leave time for the hard ones: Newtonian and non-Newtonian fluids; power-law and Herschel-Bulkley models (4 hard of 12), Large deformation and fracture (3 hard of 9), Relating instrumental and sensory texture (3 hard of 9).

    Come back to these after a first pass, untimed, and read every explanation, including for the options you rejected.

  5. Bank the easy marks: Stress, strain and rheological classification (4 easy of 10); Large deformation and fracture (3 easy of 9).

    Do these early in revision so they are fast on the day.

  6. Finish timed. Sit the subject as a timed set without notes, mark it, and send each wrong answer back to its unit above.

Last updated · How Laisha writes and checks its pages · Report a mistake

Ask Laisha about this

Opens Laisha's chat with your question ready to send. Sign in or start free.

Unlock every question — ICAR AICE-JRF/SRF Rheology & Texture of Dairy Foods

US$10 a month · one price worldwide · cancel any time

  • Every practice question in this subject, with full working
  • Timed exam papers and progress by unit
  • Ask Laisha to explain any answer — up to 1,000 questions a month
Free or Smarter
FreeSmarter
Grow guides, pest pages, articlesRead allRead all
Ask Laisha5 a dayUp to 1,000 a month
Exam practiceThe sample on each pageEvery question, timed papers
Crop calendar and pest alerts—For your own fields
Calculators and tools—All
Uploads and reports—100 a month, real files
10 days free for every new account, no card.