ICAR AICE-JRF/SRF (PhD): Dairy Chemistry, Dairy Microbiology, Dairy Technology, Dairy Engineering · India · NTA for ICAR
Original practice questions written to the published syllabus · not past papersICAR AICE-JRF/SRF (PhD): Dairy Chemistry, Dairy Microbiology, Dairy Technology, Dairy Engineering is a PhD, fellowship and lectureship exam run by NTA for ICAR, for candidates in India.
Source: icar.org.in.
Checked against the exam body's published information. Formats and fees change; confirm the current edition there before you book.
Measuring and controlling temperature, flow, pressure and level in a milk plant, from sensors to PLC and SCADA.
Our 108 ICAR AICE-JRF/SRF questions in this subject: 33 easy, 54 medium, 21 hard, across 10 units.
Choose an answer, then open the working. Each explanation says why the right answer is right and why the others are not.
These 10 were written to ICAR AICE-JRF/SRF and are not shown on any other exam's page.
A 12-bit analogue-to-digital converter digitises a 0–150 °C range. What is the approximate temperature resolution?
B. About 0.037 °C
A 12-bit converter has 2^12 = 4,096 steps: 150 ÷ 4,096 ≈ 0.037 °C. 0.59 °C is the 8-bit value (150 ÷ 256); 0.15 °C divides by 1,000; 0.012 °C divides by 12,288, which is not a converter size.
In CIP, return-line conductivity is mainly used to:
D. Detect the change between rinse water and detergent
Detergents conduct far more than water, so the return conductivity shows when full-strength detergent arrives and when rinse water replaces it. It does not measure soil films, cycle counts or velocity.
A controller's proportional band is 25%. What is its gain?
B. 4
Gain = 100 ÷ PB = 100 ÷ 25 = 4. 0.25 is PB as a fraction; 25 is PB itself; 400 multiplies instead of dividing.
Why does a proportional-only temperature controller leave an offset after a change in milk flow?
C. A non-zero error is needed to hold the valve at its new opening
With P-only control, output changes only when there is error, so a new steady load needs a steady error. P-only has no integral or derivative terms, its gain is fixed, and it responds to error, not rate.
What is the main idea of the ISA-88 batch-control standard?
D. Recipes say what to make; equipment control says how, kept separate
ISA-88 models recipes and equipment separately, so equipment phases can be reused by many recipes. Cybersecurity is IEC 62443; recorder accuracy is regulatory; screen colours are a design guideline.
What distinguishes a distributed control system (DCS) from a PLC-plus-SCADA system?
C. One integrated platform supplies controllers, I/O, stations and tools
A DCS integrates its control, I/O and operator layers in one system, traditionally for large continuous plants. It uses controllers, handles analogue signals and suits continuous processes.
A CIP detergent tank holds 2,000 L of water to be made up to 1.5% w/v sodium hydroxide using a 50% w/w caustic solution. Ignoring the volume added, how much 50% solution is needed?
D. 60 kg
NaOH needed = 2,000 L × 15 g/L = 30 kg; as 50% solution: 30 ÷ 0.5 = 60 kg. 30 kg is the pure NaOH; 15 kg halves again; 120 kg divides by 0.25.
Why is an air eliminator fitted ahead of the reception flowmeter?
A. So entrained air is not measured and paid for as milk
Air bubbles occupy volume in the meter and would be counted as milk, overpaying the supplier. The air eliminator does not cool, speed unloading or add foam.
A magnetic flowmeter records 12,000 L of milk at reception. Taking density as 1.030 kg/L, what mass is credited?
B. 12,360 kg
Mass = 12,000 × 1.030 = 12,360 kg. 11,650 kg divides by density; 12,000 kg ignores density; 12,036 kg uses 1.003.
Why must interlocks that keep CIP solution out of product lines use valve-position feedback rather than the valve command alone?
A. A stuck valve ignores its command; only feedback proves the route is closed
A command shows what the PLC asked for, not what happened; a stuck valve could let caustic reach product. Feedback switches confirm actual position. Commands are recorded, feedback does not measure flow, and screen control is not the point.
This plan follows where our questions actually fall, so the time goes where the marks are likely to be. It is our reading of the syllabus, not the exam body's weighting.
Read the manual chapters for these first and do every worked question you can find on them.
Aim for one sitting per unit, then mixed questions across them.
Learn the definitions, classifications and standard numbers; these units are more often recalled than worked.
Come back to these after a first pass, untimed, and read every explanation, including for the options you rejected.
Do these early in revision so they are fast on the day.
Last updated · How Laisha writes and checks its pages · Report a mistake
US$10 a month · one price worldwide · cancel any time
| Free | Smarter | |
|---|---|---|
| Grow guides, pest pages, articles | Read all | Read all |
| Ask Laisha | 5 a day | Up to 1,000 a month |
| Exam practice | The sample on each page | Every question, timed papers |
| Crop calendar and pest alerts | — | For your own fields |
| Calculators and tools | — | All |
| Uploads and reports | — | 100 a month, real files |
An AI operating system for agriculture: free guides, manuals and tools written for every country.