ICAR AICE-JRF/SRF (PhD): Dairy Chemistry, Dairy Microbiology, Dairy Technology, Dairy Engineering · India · NTA for ICAR
Original practice questions written to the published syllabus · not past papersICAR AICE-JRF/SRF (PhD): Dairy Chemistry, Dairy Microbiology, Dairy Technology, Dairy Engineering is a PhD, fellowship and lectureship exam run by NTA for ICAR, for candidates in India.
Source: icar.org.in.
Checked against the exam body's published information. Formats and fees change; confirm the current edition there before you book.
Process equipment and pressure vessel design: thin-shell stresses, design thickness of shells and heads, head types, supports, codes and corrosion allowance, together with equipment sizing. Expect derivation-style and numerical questions at a higher level, and comparisons of head shapes and design choices.
Planning a dairy plant from product mix to building: location, layout, equipment sizing, pressure vessels, costing and commissioning.
Our 32 ICAR AICE-JRF/SRF questions in this subject: 3 easy, 10 medium, 19 hard, across 11 units.
Choose an answer, then open the working. Each explanation says why the right answer is right and why the others are not.
These 10 were written to ICAR AICE-JRF/SRF and are not shown on any other exam's page.
Why do utility peaks in a dairy plant often coincide with cleaning periods?
D. Hot detergent and rinse water are drawn while other lines keep producing
CIP draws heated water and detergent and large rinse volumes, while other lines continue processing, so steam and water demand peak together. Production does not stop everywhere during cleaning, and hot cleaning raises steam demand.
A plant has condensation dripping from cold pipes above an open filler. Which design response addresses the cause?
D. Improve ventilation and insulate or reroute the cold pipes away from open product
Condensation forms when warm humid air meets cold surfaces; ventilation, insulation and routing cold pipes away from open product remove the source. Faster filling, more testing and drip trays do not stop drips falling onto product.
Why is hygienic zoning decided at the layout stage rather than after the building is designed?
C. It sets walls, air handling, drains and changing rooms, hard to alter later
Zones determine physical features of the building: partition walls, air handling with pressure cascades, drain routes and changing facilities. Retrofitting them in a finished building is expensive. Uniform colours follow zoning, they do not define it.
Compared with a cylinder of the same diameter and wall thickness, what is the membrane stress in a sphere under the same internal pressure?
D. Half the cylinder's hoop stress
A sphere's stress is PD/(4t) in all directions, half the cylinder's hoop stress PD/(2t). That is why hemispherical heads need about half the thickness of the shell.
Why are flat heads rarely used on vessels with significant internal pressure?
C. They bend under pressure and need very great thickness
A flat plate resists pressure by bending, so it needs much more thickness than a curved head, which resists pressure mainly by membrane tension. Flat heads are used for low pressures or small diameters and can be welded and permitted under codes.
What is a corrosion allowance in pressure vessel design?
A. Extra thickness added for metal lost in service
The required thickness from the stress formula is increased by an allowance for expected metal loss over the vessel's life; the plate ordered is the next standard size above the total. The calculated thickness from the stress formula is the starting point; the allowance is added to it.
What must a hygienic dairy pressure vessel's supports satisfy in addition to the pressure code?
B. Allow floor cleaning beneath and avoid crevices that trap soil
Legs and supports must leave space to clean the floor and must not create crevices or ledges, so hygienic design rules apply alongside the structural ones. Rusting supports and supports set into drains are unhygienic.
A pump moves 30 cubic metres per hour of a liquid of density 1,000 kg/m³ against a total head of 25 m with 65 percent efficiency. What shaft power is needed?
C. About 3.1 kW
Hydraulic power = ρgQH = 1,000 × 9.81 × (30/3,600) × 25 = 2.04 kW; shaft power = 2.04 ÷ 0.65 = 3.1 kW. 2.0 kW ignores efficiency; 4.8 kW divides twice; 1.3 kW multiplies by efficiency instead of dividing.
Why are services routed through service corridors or external pipe bridges where possible?
D. Maintenance staff can work on them without entering high-hygiene rooms
Keeping valves, unions and services outside high-hygiene rooms reduces traffic and contamination risk during maintenance. Pipe lengths and insulation needs are not reduced by this, and some pipes must enter production rooms.
Why are internal welds on dairy product pipelines inspected, for example with a borescope?
D. A poor internal weld leaves an uncleanable crevice
Lack of penetration or rough internal welds leave crevices where soil and bacteria lodge and CIP cannot reach. Inspection finds them before the line enters service.
This plan follows where our questions actually fall, so the time goes where the marks are likely to be. It is our reading of the syllabus, not the exam body's weighting.
Read the manual chapters for these first and do every worked question you can find on them.
Aim for one sitting per unit, then mixed questions across them.
Learn the definitions, classifications and standard numbers; these units are more often recalled than worked.
Come back to these after a first pass, untimed, and read every explanation, including for the options you rejected.
Do these early in revision so they are fast on the day.
Last updated · How Laisha writes and checks its pages · Report a mistake
US$10 a month · one price worldwide · cancel any time
| Free | Smarter | |
|---|---|---|
| Grow guides, pest pages, articles | Read all | Read all |
| Ask Laisha | 5 a day | Up to 1,000 a month |
| Exam practice | The sample on each page | Every question, timed papers |
| Crop calendar and pest alerts | — | For your own fields |
| Calculators and tools | — | All |
| Uploads and reports | — | 100 a month, real files |
An AI operating system for agriculture: free guides, manuals and tools written for every country.